General Pump

General Pump ZGRS1000 Gear Reducer for 2.2 to 1, 1″ Shafted Engines, Up to 25 HP, J609A Flange, 47 and 66 Series pumps

Features:
• Eliminates need for belts and pulleys. Saves time and money
• Compact design for easier enclosure. Reduced size of mounting base
• Oversized bearing system is self-aligning. Reduces load on motor bearings and pump bearings
• Self-contained lubrication system Uses 90W gear lube for quiet, long life operation. Protects pump from failure due to gearbox oil loss. Protects gearbox from failure due to oil loss in pump
• Large, helical cut, hardened steel gears for quiet, long life operation
• Large capacity crankcase
• Reversible mounting for right or left hand drive gas engines. Includes reversible dipstick and oil level sight glass
• Model ZGRS1000 for a 1” keyed shaft

Specifications:
• Maximum BHP (Engine HP): 25
• Maximum Engine RPM: 3,600
• Reduction Ratio: 1:2.2
• Maximum Pump Speed: 1,450 RPM
• Oil Capacity (SP Industrial Pump Oil Series 220): 9.47 Oz
• Fits Engine Shaft Diameter: 1”
• Fits General Pump Models: 47 Series (1450 RPM Versions) 66 Series (1450 RPM Versions)
• Weight: 9.26 lb.

General Pump YGR1000P Gear Reducer for 2.2 to 1, 1″ Shafted Engines, Up to 24 HP, J609A Flange, 47, 47SS and 66 Series pumps

Features:
• Compact and lightweight
• Hardened steel helical gears for quiet operation
• Oil bath lubrication
• Dual bearing design for extended life
• J609a Flange mounts to most gasoline engines

Specifications:
• Horse Power: 18 - 24
• Drive Ratio: 2.176:1
• Maximum Pump Speed: 1,450 RPM
• Oil Capacity: 10 Oz
• Oil Grade: SAE90 Gear Lube
• Input (motor) Shaft Ø": 1”
• Output (pump) Shaft Ø": 24 mm
• Motor Flange (SAE): J609A
• Pump Flange: Fits 47, 47SS and 66 Series General Pump
• Weight: 5.8 lb.

1/4” General Pump # 5.5 “Flusher” Type Sewer Nozzle 0 Front 3 Rear 5,000 PSI.

Features
• “Flusher” nozzles expel loose debris as hose travels through pipe
• 3 Rear (25°) facing nozzles advance hose through pipe
• High pressure nozzles are sized to match the flow and pressure specifications of the equipment
• Heat-treated Stainless Steel nozzles are wear and corrosion resistant
• Great for pipe, sewer and drain cleaning
• Compact design allows for maneuverability and cornering within pipes
• Works best on 2" to 4" Pipes

Specifications
• Nozzle Size: # 5.5
• Material: Stainless steel
• Maximum Pressure: 5,000 PSI
• Inlet: 1/4" NPT-F
• Outside Diameter (O.D.): .63”
• Weight: .05 lb

Please use Nozzle Chart to determine proper nozzle size

Nozzle Chart

1/4” General Pump # 5.0 “Flusher” Type Sewer Nozzle 0 Front 3 Rear 5,000 PSI.

Features
• “Flusher” nozzles expel loose debris as hose travels through pipe
• 3 Rear (25°) facing nozzles advance hose through pipe
• High pressure nozzles are sized to match the flow and pressure specifications of the equipment
• Heat-treated Stainless Steel nozzles are wear and corrosion resistant
• Great for pipe, sewer and drain cleaning
• Compact design allows for maneuverability and cornering within pipes
• Works best on 2" to 4" Pipes

Specifications
• Nozzle Size: # 5.0
• Material: Stainless steel
• Maximum Pressure: 5,000 PSI
• Inlet: 1/4" NPT-F
• Outside Diameter (O.D.): .63”
• Weight: .05 lb

Please use Nozzle Chart to determine proper nozzle size

Nozzle Chart

1/4” General Pump # 4.5 “Flusher” Type Sewer Nozzle 0 Front 3 Rear 5,000 PSI.

Features
• “Flusher” nozzles expel loose debris as hose travels through pipe
• 3 Rear (25°) facing nozzles advance hose through pipe
• High pressure nozzles are sized to match the flow and pressure specifications of the equipment
• Heat-treated Stainless Steel nozzles are wear and corrosion resistant
• Great for pipe, sewer and drain cleaning
• Compact design allows for maneuverability and cornering within pipes
• Works best on 2" to 4" Pipes

Specifications
• Nozzle Size: # 4.5
• Material: Stainless steel
• Maximum Pressure: 5,000 PSI
• Inlet: 1/4" NPT-F
• Outside Diameter (O.D.): .63”
• Weight: .05 lb

Please use Nozzle Chart to determine proper nozzle size

Nozzle Chart

1/4” General Pump # 4.0 “Flusher” Type Sewer Nozzle 0 Front 3 Rear 5,000 PSI.

Features
• “Flusher” nozzles expel loose debris as hose travels through pipe
• 3 Rear (25°) facing nozzles advance hose through pipe
• High pressure nozzles are sized to match the flow and pressure specifications of the equipment
• Heat-treated Stainless Steel nozzles are wear and corrosion resistant
• Great for pipe, sewer and drain cleaning
• Compact design allows for maneuverability and cornering within pipes
• Works best on 2" to 4" Pipes

Specifications
• Nozzle Size: # 4.0
• Material: Stainless steel
• Maximum Pressure: 5,000 PSI
• Inlet: 1/4" NPT-F
• Outside Diameter (O.D.): .63”
• Weight: .05 lb

Please use Nozzle Chart to determine proper nozzle size

Nozzle Chart

1/4” General Pump # 3.0 “Flusher” Type Sewer Nozzle 0 Front 3 Rear 5,000 PSI.

Features
• “Flusher” nozzles expel loose debris as hose travels through pipe
• 3 Rear (25°) facing nozzles advance hose through pipe
• High pressure nozzles are sized to match the flow and pressure specifications of the equipment
• Heat-treated Stainless Steel nozzles are wear and corrosion resistant
• Great for pipe, sewer and drain cleaning
• Compact design allows for maneuverability and cornering within pipes
• Works best on 2" to 4" Pipes

Specifications
• Nozzle Size: # 3.0
• Material: Stainless steel
• Maximum Pressure: 5,000 PSI
• Inlet: 1/4" NPT-F
• Outside Diameter (O.D.): .63”
• Weight: .05 lb

Please use Nozzle Chart to determine proper nozzle size

Nozzle Chart

General Pump ZFWWU Flange For NEMA-C Electric Motors 56C Frame (TT/TP Series 51 Pumps)

Specifications:
• Material: Heavy-duty cast aluminum
• Pump Series: TT/TP 51 Series
• Motor Frame: NEMA-C Electric 56C
• Motor Rating: 3-1/2 to 8 HP
• Weight: lb.

General Pump 100323 5,000 PSI Easy Start Valve 3/8” NPT-M Inlet & 1/4” Hose Barb. Eases system start-up. Especially useful for engine-driven pressure washers

Features:
• Fits any brand pump
• Max working pressure of 5,000 PSI
• Designed and made in the USA
• Long-life construction
• Improved seal design limits leaks

Specifications:
• Maximum Pressure: 5,000 PSI
• Max Volume: 8 GPM
• Maximum Temperature: 195° F
• Inlet: 3/8" NPT-M
• Outlet: 1/4” Hose Barb
• Materials: Brass, Stainless Steel, Thermoplastic
• Weight: 0.25 lbs

General Pump 100544 5,000 PSI Easy Start Valve 3/8” NPT-M Inlet & 1/8” NPT-F Outlet. Eases system start-up. Especially useful for engine-driven pressure washers

Features:
• Fits any brand pump
• Max working pressure of 5,000 PSI
• Designed and made in the USA
• Long-life construction
• Improved seal design limits leaks

Specifications:
• Maximum Pressure: 5,000 PSI
• Max Volume: 8 GPM
• Maximum Temperature: 195° F
• Inlet: 3/8" NPT-M
• Outlet: 1/8” NPT-F
• Materials: Brass, Stainless Steel, Thermoplastic
• Weight: 0.25 lbs

General DCG5010HE Compensating Spray Gun for Hydro Excavation.

Features:
• Specifically designed for use in hydro excavation!
• Exclusive patented GP design
• Unique design compensates for changes in pressure
• Trigger designed for low fatigue
• Allows for continued use without tiring hand
• All flow passages designed for minimum pressure drop - maximum flow
• Fluorocarbon seals for maximum high temperature performance
• Large comfortable hand grip to accommodate work gloves
• Additional venting for excellent high temperature performance
• Durable glass-filled housing and trigger in Zytel (high tech nylon)

Specifications:
• Max Pressure: 5,000 PSI
• Max Flow: 10.5 GPM
• Max Temp: 320° F.
• Inlet: 3/8" Female NPT
• Outlet: 1/4" Female NPT
• Weight: 1.4 lbs

General Pump 100719 Clutch w/Mounting Plate 47, 66 and 59(ES) Series, 24V, Dual Groove. Mobile Clutch for 24mm Solid Shaft Pump

Features:
• Solid forged rotor. A one-piece solid forged rotor means no chance of internal parts separation. They have an even wall thickness around the coil which gives optimum flux distribution, maximizing torque.
• Different coil voltages available. 12 volt is the most common; 24 volt clutches are also available.
• High temperature, longer-life grease. Our special long-life grease has shown a significant improvement in life over other standard high temp greases.
• E-coating. Where possible, all parts in the clutch are e-coated to give maximum corrosion protection.
• High-temperature epoxy coil. To help prevent failure from vibration and outside contaminants, all coils are sealed in the coil shell with a high-temperature epoxy coating.
• Forged machined pulley. All GP models use a heavy-duty machined pulley. A stronger pulley resists damage

Data Sheet

Specifications:
• Pulley Size & Type: 7" - A Groove, 24mm Shaft
• Width: 2.25"
• Torque After Burnishing: 75 - 95 lbs.
• Power Requirement: 24V 45.6 Watts
• Weight: 8.0 lbs

General Pump 100719 Clutch w/Mounting Plate 47, 66 and 59(ES) Series, 12V, Single Groove. Mobile Clutch for 24mm Solid Shaft Pump

Features:
• Solid forged rotor. A one-piece solid forged rotor means no chance of internal parts separation. They have an even wall thickness around the coil which gives optimum flux distribution, maximizing torque.
• Different coil voltages available. 12 volt is the most common; 24 volt clutches are also available.
• High temperature, longer-life grease. Our special long-life grease has shown a significant improvement in life over other standard high temp greases.
• E-coating. Where possible, all parts in the clutch are e-coated to give maximum corrosion protection.
• High-temperature epoxy coil. To help prevent failure from vibration and outside contaminants, all coils are sealed in the coil shell with a high-temperature epoxy coating.
• Forged machined pulley. All GP models use a heavy-duty machined pulley. A stronger pulley resists damage

Data Sheet

Specifications:
• Pulley Size & Type: 7" - A Groove, 24mm Shaft
• Width: 2.25"
• Torque After Burnishing: 75 - 95 lbs.
• Power Requirement: 12V 47 Watts
• Weight: 8.0 lbs

General Pump 100687 Clutch w/Mounting Plate 47, 66 and 59(ES) Series, 12V, Dual Groove. Mobile Clutch for 24mm Solid Shaft Pump

Features:
• Solid forged rotor. A one-piece solid forged rotor means no chance of internal parts separation. They have an even wall thickness around the coil which gives optimum flux distribution, maximizing torque.
• Different coil voltages available. 12 volt is the most common; 24 volt clutches are also available.
• High temperature, longer-life grease. Our special long-life grease has shown a significant improvement in life over other standard high temp greases.
• E-coating. Where possible, all parts in the clutch are e-coated to give maximum corrosion protection.
• High-temperature epoxy coil. To help prevent failure from vibration and outside contaminants, all coils are sealed in the coil shell with a high-temperature epoxy coating.
• Forged machined pulley. All GP models use a heavy-duty machined pulley. A stronger pulley resists damage

Data Sheet

Specifications:
• Pulley Size & Type: 7" - A Groove, 24mm Shaft
• Width: 2.25"
• Torque After Burnishing: 75 - 95 lbs.
• Power Requirement: 12V 47 Watts
• Weight: 8.0 lbs

General Pump 100720 Clutch w/Mounting Plate 44, 50, 63 and 58 (ES) Series, 24V, Dual Groove. Mobile Clutch for 24mm Solid Shaft Pump

Features:
• Solid forged rotor. A one-piece solid forged rotor means no chance of internal parts separation. They have an even wall thickness around the coil which gives optimum flux distribution, maximizing torque.
• Different coil voltages available. 12 volt is the most common; 24 volt clutches are also available.
• High temperature, longer-life grease. Our special long-life grease has shown a significant improvement in life over other standard high temp greases.
• E-coating. Where possible, all parts in the clutch are e-coated to give maximum corrosion protection.
• High-temperature epoxy coil. To help prevent failure from vibration and outside contaminants, all coils are sealed in the coil shell with a high-temperature epoxy coating.
• Forged machined pulley. All GP models use a heavy-duty machined pulley. A stronger pulley resists damage

Data Sheet

Specifications:
• Pulley Size & Type: 7" - A Groove, 24mm Shaft
• Width: 2.25"
• Torque After Burnishing: 75 - 95 lbs.
• Power Requirement: 24V 45.6 Watts
• Weight: 8.0 lbs

General Pump 100720 Clutch w/Mounting Plate 44, 50, 63 and 58 (ES) Series, 12V, Single Groove. Mobile Clutch for 24mm Solid Shaft Pump

Features:
• Solid forged rotor. A one-piece solid forged rotor means no chance of internal parts separation. They have an even wall thickness around the coil which gives optimum flux distribution, maximizing torque.
• Different coil voltages available. 12 volt is the most common; 24 volt clutches are also available.
• High temperature, longer-life grease. Our special long-life grease has shown a significant improvement in life over other standard high temp greases.
• E-coating. Where possible, all parts in the clutch are e-coated to give maximum corrosion protection.
• High-temperature epoxy coil. To help prevent failure from vibration and outside contaminants, all coils are sealed in the coil shell with a high-temperature epoxy coating.
• Forged machined pulley. All GP models use a heavy-duty machined pulley. A stronger pulley resists damage

Data Sheet

Specifications:
• Pulley Size & Type: 7" - A Groove, 24mm Shaft
• Width: 2.25"
• Torque After Burnishing: 75 - 95 lbs.
• Power Requirement: 12V 47 Watts
• Weight: 8.0 lbs

General Pump 100688 Clutch w/Mounting Plate 44, 50, 63 and 58 (ES) Series, 12V, Dual Groove. Mobile Clutch for 24mm Solid Shaft Pump

Features:
• Solid forged rotor. A one-piece solid forged rotor means no chance of internal parts separation. They have an even wall thickness around the coil which gives optimum flux distribution, maximizing torque.
• Different coil voltages available. 12 volt is the most common; 24 volt clutches are also available.
• High temperature, longer-life grease. Our special long-life grease has shown a significant improvement in life over other standard high temp greases.
• E-coating. Where possible, all parts in the clutch are e-coated to give maximum corrosion protection.
• High-temperature epoxy coil. To help prevent failure from vibration and outside contaminants, all coils are sealed in the coil shell with a high-temperature epoxy coating.
• Forged machined pulley. All GP models use a heavy-duty machined pulley. A stronger pulley resists damage

Data Sheet

Specifications:
• Pulley Size & Type: 7" - A Groove, 24mm Shaft
• Width: 2.25"
• Torque After Burnishing: 75 - 95 lbs.
• Power Requirement: 12V 47 Watts
• Weight: 8.0 lbs

GP 2103139 Brake Repair Kit for DHRA Hose Reels

Kit Includes:
• 2660268 Brake x 1
• 2200103 Bolt, M8 x 1
• 2660405 Knob, Brake x 1
• 2200013 Washer, M8, SS x 1

General Pump 65° #40.0 Q-Style Brass Soap (Black) Nozzle. General Pump offers a complete range of chemical nozzles. These nozzles have been designed and manufactured with the same exacting standards as the high pressure tips

Features
• Made in the USA
• Brass body
• Large color coded tip protector on Q-type nozzles permits rapid identification

Specifications
• Tip Angle: 65°
• Nozzle Size: 40.0
• Color Code: Black
• Style: Q
• Connection: 1/4” QC Plug
• Weight: 0.05 oz

General Pump 65° #40.0 S-Style Brass Soap Nozzle. General Pump offers a complete range of chemical nozzles. These nozzles have been designed and manufactured with the same exacting standards as the high pressure tips

Features
• Made in the USA
• Low Pressure Spray Nozzle
• Brass construction

Specifications
• Tip Angle: 65°
• Nozzle Size: 40.0
• Style: S
• Connection: 1/8” NPT-M
• Weight: 0.05 oz