General Pump

General Pump YGR1000P Gear Reducer for 2.2 to 1, 1″ Shafted Engines, Up to 24 HP, J609A Flange, 47, 47SS and 66 Series pumps

Features:
• Compact and lightweight
• Hardened steel helical gears for quiet operation
• Oil bath lubrication
• Dual bearing design for extended life
• J609a Flange mounts to most gasoline engines

Specifications:
• Horse Power: 18 - 24
• Drive Ratio: 2.176:1
• Maximum Pump Speed: 1,450 RPM
• Oil Capacity: 10 Oz
• Oil Grade: SAE90 Gear Lube
• Input (motor) Shaft Ø": 1”
• Output (pump) Shaft Ø": 24 mm
• Motor Flange (SAE): J609A
• Pump Flange: Fits 47, 47SS and 66 Series General Pump
• Weight: 5.8 lb.

1/4” General Pump # 5.5 “Flusher” Type Sewer Nozzle 0 Front 3 Rear 5,000 PSI.

Features
• “Flusher” nozzles expel loose debris as hose travels through pipe
• 3 Rear (25°) facing nozzles advance hose through pipe
• High pressure nozzles are sized to match the flow and pressure specifications of the equipment
• Heat-treated Stainless Steel nozzles are wear and corrosion resistant
• Great for pipe, sewer and drain cleaning
• Compact design allows for maneuverability and cornering within pipes
• Works best on 2" to 4" Pipes

Specifications
• Nozzle Size: # 5.5
• Material: Stainless steel
• Maximum Pressure: 5,000 PSI
• Inlet: 1/4" NPT-F
• Outside Diameter (O.D.): .63”
• Weight: .05 lb

Please use Nozzle Chart to determine proper nozzle size

Nozzle Chart

1/4” General Pump # 5.0 “Flusher” Type Sewer Nozzle 0 Front 3 Rear 5,000 PSI.

Features
• “Flusher” nozzles expel loose debris as hose travels through pipe
• 3 Rear (25°) facing nozzles advance hose through pipe
• High pressure nozzles are sized to match the flow and pressure specifications of the equipment
• Heat-treated Stainless Steel nozzles are wear and corrosion resistant
• Great for pipe, sewer and drain cleaning
• Compact design allows for maneuverability and cornering within pipes
• Works best on 2" to 4" Pipes

Specifications
• Nozzle Size: # 5.0
• Material: Stainless steel
• Maximum Pressure: 5,000 PSI
• Inlet: 1/4" NPT-F
• Outside Diameter (O.D.): .63”
• Weight: .05 lb

Please use Nozzle Chart to determine proper nozzle size

Nozzle Chart

1/4” General Pump # 4.5 “Flusher” Type Sewer Nozzle 0 Front 3 Rear 5,000 PSI.

Features
• “Flusher” nozzles expel loose debris as hose travels through pipe
• 3 Rear (25°) facing nozzles advance hose through pipe
• High pressure nozzles are sized to match the flow and pressure specifications of the equipment
• Heat-treated Stainless Steel nozzles are wear and corrosion resistant
• Great for pipe, sewer and drain cleaning
• Compact design allows for maneuverability and cornering within pipes
• Works best on 2" to 4" Pipes

Specifications
• Nozzle Size: # 4.5
• Material: Stainless steel
• Maximum Pressure: 5,000 PSI
• Inlet: 1/4" NPT-F
• Outside Diameter (O.D.): .63”
• Weight: .05 lb

Please use Nozzle Chart to determine proper nozzle size

Nozzle Chart

1/4” General Pump # 4.0 “Flusher” Type Sewer Nozzle 0 Front 3 Rear 5,000 PSI.

Features
• “Flusher” nozzles expel loose debris as hose travels through pipe
• 3 Rear (25°) facing nozzles advance hose through pipe
• High pressure nozzles are sized to match the flow and pressure specifications of the equipment
• Heat-treated Stainless Steel nozzles are wear and corrosion resistant
• Great for pipe, sewer and drain cleaning
• Compact design allows for maneuverability and cornering within pipes
• Works best on 2" to 4" Pipes

Specifications
• Nozzle Size: # 4.0
• Material: Stainless steel
• Maximum Pressure: 5,000 PSI
• Inlet: 1/4" NPT-F
• Outside Diameter (O.D.): .63”
• Weight: .05 lb

Please use Nozzle Chart to determine proper nozzle size

Nozzle Chart

1/4” General Pump # 3.0 “Flusher” Type Sewer Nozzle 0 Front 3 Rear 5,000 PSI.

Features
• “Flusher” nozzles expel loose debris as hose travels through pipe
• 3 Rear (25°) facing nozzles advance hose through pipe
• High pressure nozzles are sized to match the flow and pressure specifications of the equipment
• Heat-treated Stainless Steel nozzles are wear and corrosion resistant
• Great for pipe, sewer and drain cleaning
• Compact design allows for maneuverability and cornering within pipes
• Works best on 2" to 4" Pipes

Specifications
• Nozzle Size: # 3.0
• Material: Stainless steel
• Maximum Pressure: 5,000 PSI
• Inlet: 1/4" NPT-F
• Outside Diameter (O.D.): .63”
• Weight: .05 lb

Please use Nozzle Chart to determine proper nozzle size

Nozzle Chart

General Pump ZFWWU Flange For NEMA-C Electric Motors 56C Frame (TT/TP Series 51 Pumps)

Specifications:
• Material: Heavy-duty cast aluminum
• Pump Series: TT/TP 51 Series
• Motor Frame: NEMA-C Electric 56C
• Motor Rating: 3-1/2 to 8 HP
• Weight: lb.

General Pump 100323 5,000 PSI Easy Start Valve 3/8” NPT-M Inlet & 1/4” Hose Barb. Eases system start-up. Especially useful for engine-driven pressure washers

Features:
• Fits any brand pump
• Max working pressure of 5,000 PSI
• Designed and made in the USA
• Long-life construction
• Improved seal design limits leaks

Specifications:
• Maximum Pressure: 5,000 PSI
• Max Volume: 8 GPM
• Maximum Temperature: 195° F
• Inlet: 3/8" NPT-M
• Outlet: 1/4” Hose Barb
• Materials: Brass, Stainless Steel, Thermoplastic
• Weight: 0.25 lbs

General Pump 100544 5,000 PSI Easy Start Valve 3/8” NPT-M Inlet & 1/8” NPT-F Outlet. Eases system start-up. Especially useful for engine-driven pressure washers

Features:
• Fits any brand pump
• Max working pressure of 5,000 PSI
• Designed and made in the USA
• Long-life construction
• Improved seal design limits leaks

Specifications:
• Maximum Pressure: 5,000 PSI
• Max Volume: 8 GPM
• Maximum Temperature: 195° F
• Inlet: 3/8" NPT-M
• Outlet: 1/8” NPT-F
• Materials: Brass, Stainless Steel, Thermoplastic
• Weight: 0.25 lbs

General DCG5010HE Compensating Spray Gun for Hydro Excavation.

Features:
• Specifically designed for use in hydro excavation!
• Exclusive patented GP design
• Unique design compensates for changes in pressure
• Trigger designed for low fatigue
• Allows for continued use without tiring hand
• All flow passages designed for minimum pressure drop - maximum flow
• Fluorocarbon seals for maximum high temperature performance
• Large comfortable hand grip to accommodate work gloves
• Additional venting for excellent high temperature performance
• Durable glass-filled housing and trigger in Zytel (high tech nylon)

Specifications:
• Max Pressure: 5,000 PSI
• Max Flow: 10.5 GPM
• Max Temp: 320° F.
• Inlet: 3/8" Female NPT
• Outlet: 1/4" Female NPT
• Weight: 1.4 lbs

General Pump 100719 Clutch w/Mounting Plate 47, 66 and 59(ES) Series, 24V, Dual Groove. Mobile Clutch for 24mm Solid Shaft Pump

Features:
• Solid forged rotor. A one-piece solid forged rotor means no chance of internal parts separation. They have an even wall thickness around the coil which gives optimum flux distribution, maximizing torque.
• Different coil voltages available. 12 volt is the most common; 24 volt clutches are also available.
• High temperature, longer-life grease. Our special long-life grease has shown a significant improvement in life over other standard high temp greases.
• E-coating. Where possible, all parts in the clutch are e-coated to give maximum corrosion protection.
• High-temperature epoxy coil. To help prevent failure from vibration and outside contaminants, all coils are sealed in the coil shell with a high-temperature epoxy coating.
• Forged machined pulley. All GP models use a heavy-duty machined pulley. A stronger pulley resists damage

Data Sheet

Specifications:
• Pulley Size & Type: 7" - A Groove, 24mm Shaft
• Width: 2.25"
• Torque After Burnishing: 75 - 95 lbs.
• Power Requirement: 24V 45.6 Watts
• Weight: 8.0 lbs

General Pump 100719 Clutch w/Mounting Plate 47, 66 and 59(ES) Series, 12V, Single Groove. Mobile Clutch for 24mm Solid Shaft Pump

Features:
• Solid forged rotor. A one-piece solid forged rotor means no chance of internal parts separation. They have an even wall thickness around the coil which gives optimum flux distribution, maximizing torque.
• Different coil voltages available. 12 volt is the most common; 24 volt clutches are also available.
• High temperature, longer-life grease. Our special long-life grease has shown a significant improvement in life over other standard high temp greases.
• E-coating. Where possible, all parts in the clutch are e-coated to give maximum corrosion protection.
• High-temperature epoxy coil. To help prevent failure from vibration and outside contaminants, all coils are sealed in the coil shell with a high-temperature epoxy coating.
• Forged machined pulley. All GP models use a heavy-duty machined pulley. A stronger pulley resists damage

Data Sheet

Specifications:
• Pulley Size & Type: 7" - A Groove, 24mm Shaft
• Width: 2.25"
• Torque After Burnishing: 75 - 95 lbs.
• Power Requirement: 12V 47 Watts
• Weight: 8.0 lbs

General Pump 100687 Clutch w/Mounting Plate 47, 66 and 59(ES) Series, 12V, Dual Groove. Mobile Clutch for 24mm Solid Shaft Pump

Features:
• Solid forged rotor. A one-piece solid forged rotor means no chance of internal parts separation. They have an even wall thickness around the coil which gives optimum flux distribution, maximizing torque.
• Different coil voltages available. 12 volt is the most common; 24 volt clutches are also available.
• High temperature, longer-life grease. Our special long-life grease has shown a significant improvement in life over other standard high temp greases.
• E-coating. Where possible, all parts in the clutch are e-coated to give maximum corrosion protection.
• High-temperature epoxy coil. To help prevent failure from vibration and outside contaminants, all coils are sealed in the coil shell with a high-temperature epoxy coating.
• Forged machined pulley. All GP models use a heavy-duty machined pulley. A stronger pulley resists damage

Data Sheet

Specifications:
• Pulley Size & Type: 7" - A Groove, 24mm Shaft
• Width: 2.25"
• Torque After Burnishing: 75 - 95 lbs.
• Power Requirement: 12V 47 Watts
• Weight: 8.0 lbs

General Pump 100720 Clutch w/Mounting Plate 44, 50, 63 and 58 (ES) Series, 24V, Dual Groove. Mobile Clutch for 24mm Solid Shaft Pump

Features:
• Solid forged rotor. A one-piece solid forged rotor means no chance of internal parts separation. They have an even wall thickness around the coil which gives optimum flux distribution, maximizing torque.
• Different coil voltages available. 12 volt is the most common; 24 volt clutches are also available.
• High temperature, longer-life grease. Our special long-life grease has shown a significant improvement in life over other standard high temp greases.
• E-coating. Where possible, all parts in the clutch are e-coated to give maximum corrosion protection.
• High-temperature epoxy coil. To help prevent failure from vibration and outside contaminants, all coils are sealed in the coil shell with a high-temperature epoxy coating.
• Forged machined pulley. All GP models use a heavy-duty machined pulley. A stronger pulley resists damage

Data Sheet

Specifications:
• Pulley Size & Type: 7" - A Groove, 24mm Shaft
• Width: 2.25"
• Torque After Burnishing: 75 - 95 lbs.
• Power Requirement: 24V 45.6 Watts
• Weight: 8.0 lbs

General Pump 100720 Clutch w/Mounting Plate 44, 50, 63 and 58 (ES) Series, 12V, Single Groove. Mobile Clutch for 24mm Solid Shaft Pump

Features:
• Solid forged rotor. A one-piece solid forged rotor means no chance of internal parts separation. They have an even wall thickness around the coil which gives optimum flux distribution, maximizing torque.
• Different coil voltages available. 12 volt is the most common; 24 volt clutches are also available.
• High temperature, longer-life grease. Our special long-life grease has shown a significant improvement in life over other standard high temp greases.
• E-coating. Where possible, all parts in the clutch are e-coated to give maximum corrosion protection.
• High-temperature epoxy coil. To help prevent failure from vibration and outside contaminants, all coils are sealed in the coil shell with a high-temperature epoxy coating.
• Forged machined pulley. All GP models use a heavy-duty machined pulley. A stronger pulley resists damage

Data Sheet

Specifications:
• Pulley Size & Type: 7" - A Groove, 24mm Shaft
• Width: 2.25"
• Torque After Burnishing: 75 - 95 lbs.
• Power Requirement: 12V 47 Watts
• Weight: 8.0 lbs

General Pump 100688 Clutch w/Mounting Plate 44, 50, 63 and 58 (ES) Series, 12V, Dual Groove. Mobile Clutch for 24mm Solid Shaft Pump

Features:
• Solid forged rotor. A one-piece solid forged rotor means no chance of internal parts separation. They have an even wall thickness around the coil which gives optimum flux distribution, maximizing torque.
• Different coil voltages available. 12 volt is the most common; 24 volt clutches are also available.
• High temperature, longer-life grease. Our special long-life grease has shown a significant improvement in life over other standard high temp greases.
• E-coating. Where possible, all parts in the clutch are e-coated to give maximum corrosion protection.
• High-temperature epoxy coil. To help prevent failure from vibration and outside contaminants, all coils are sealed in the coil shell with a high-temperature epoxy coating.
• Forged machined pulley. All GP models use a heavy-duty machined pulley. A stronger pulley resists damage

Data Sheet

Specifications:
• Pulley Size & Type: 7" - A Groove, 24mm Shaft
• Width: 2.25"
• Torque After Burnishing: 75 - 95 lbs.
• Power Requirement: 12V 47 Watts
• Weight: 8.0 lbs

GP 2103139 Brake Repair Kit for DHRA Hose Reels

Kit Includes:
• 2660268 Brake x 1
• 2200103 Bolt, M8 x 1
• 2660405 Knob, Brake x 1
• 2200013 Washer, M8, SS x 1

General Pump 65° #40.0 Q-Style Brass Soap (Black) Nozzle. General Pump offers a complete range of chemical nozzles. These nozzles have been designed and manufactured with the same exacting standards as the high pressure tips

Features
• Made in the USA
• Brass body
• Large color coded tip protector on Q-type nozzles permits rapid identification

Specifications
• Tip Angle: 65°
• Nozzle Size: 40.0
• Color Code: Black
• Style: Q
• Connection: 1/4” QC Plug
• Weight: 0.05 oz

General Pump 65° #40.0 S-Style Brass Soap Nozzle. General Pump offers a complete range of chemical nozzles. These nozzles have been designed and manufactured with the same exacting standards as the high pressure tips

Features
• Made in the USA
• Low Pressure Spray Nozzle
• Brass construction

Specifications
• Tip Angle: 65°
• Nozzle Size: 40.0
• Style: S
• Connection: 1/8” NPT-M
• Weight: 0.05 oz

General Pump 65° #40.0 M-Style Brass Soap Nozzle. General Pump offers a complete range of chemical nozzles. These nozzles have been designed and manufactured with the same exacting standards as the high pressure tips

Features
• Made in the USA
• Low Pressure Spray Nozzle
• Brass construction

Specifications
• Tip Angle: 65°
• Nozzle Size: 40.0
• Style: M
• Connection: 1/4” NPT-M
• Weight: 0.05 oz