General Pump

General EZ2555S 2500 PSI, 5.5 GPM Solid Shaft Pump for belt drive, flex coupling or gear reduction

Features:
• Solid ceramic plunger design
• Flex coupling and bell housing available for direct drive
• Forged brass manifold with 4:1 hydrostatic rating
• Die-cast, anodized aluminum, oil-bath crankcase
• Premium roller bearing
• Unitized stainless steel inlet and discharge valves
• Available in “L” left-handed versions

WARNING: High Pressure Systems require a primary pressure regulating device (i.e. regulator, unloader) and a secondary pressure relief device (i.e. pop-off valve, relief valve). Failure to install such relief devices properly could result in personal injury or damage to pump or property. GP and PRI Industries do not assume any liability or responsibility for the operation of the user’s high pressure system.

Specifications Sheet

Specifications:
• Triplex Plunger Pump
• Max. Volume: 5.5 GPM
• Max. Discharge Pressure: 2,500 PSI
• Max. Pump Speed: 3,400 RPM
• Shaft Diameter: 24MM Solid
• Max. Horsepower Requirements: 9.4 EBHP
• Max. Fluid Temp.: 165 degrees F.
• Inlet Ports (2): 1/2-14 BSPP-F
• Discharge Ports (2): 3/8-19 BSPP-F
• Drive Side: Standard right>
• Crankcase Oil Capacity: 14.0 oz
• Note: Item for sale is PUMP ONLY as shown in picture and does not include unloader which is required for proper operation
• Weight: 18.0 lb.

General Pump 100687 Clutch w/Mounting Plate 47, 66 and 59(ES) Series, 12V, Dual Groove. Mobile Clutch for 24mm Solid Shaft Pump

Features:
• Solid forged rotor. A one-piece solid forged rotor means no chance of internal parts separation. They have an even wall thickness around the coil which gives optimum flux distribution, maximizing torque.
• Different coil voltages available. 12 volt is the most common; 24 volt clutches are also available.
• High temperature, longer-life grease. Our special long-life grease has shown a significant improvement in life over other standard high temp greases.
• E-coating. Where possible, all parts in the clutch are e-coated to give maximum corrosion protection.
• High-temperature epoxy coil. To help prevent failure from vibration and outside contaminants, all coils are sealed in the coil shell with a high-temperature epoxy coating.
• Forged machined pulley. All GP models use a heavy-duty machined pulley. A stronger pulley resists damage

Data Sheet

Specifications:
• Pulley Size & Type: 7" - A Groove, 24mm Shaft
• Width: 2.25"
• Torque After Burnishing: 75 - 95 lbs.
• Power Requirement: 12V 47 Watts
• Weight: 8.0 lbs

General Pump 100688 Clutch w/Mounting Plate 44, 50, 63 and 58 (ES) Series, 12V, Dual Groove. Mobile Clutch for 24mm Solid Shaft Pump

Features:
• Solid forged rotor. A one-piece solid forged rotor means no chance of internal parts separation. They have an even wall thickness around the coil which gives optimum flux distribution, maximizing torque.
• Different coil voltages available. 12 volt is the most common; 24 volt clutches are also available.
• High temperature, longer-life grease. Our special long-life grease has shown a significant improvement in life over other standard high temp greases.
• E-coating. Where possible, all parts in the clutch are e-coated to give maximum corrosion protection.
• High-temperature epoxy coil. To help prevent failure from vibration and outside contaminants, all coils are sealed in the coil shell with a high-temperature epoxy coating.
• Forged machined pulley. All GP models use a heavy-duty machined pulley. A stronger pulley resists damage

Data Sheet

Specifications:
• Pulley Size & Type: 7" - A Groove, 24mm Shaft
• Width: 2.25"
• Torque After Burnishing: 75 - 95 lbs.
• Power Requirement: 12V 47 Watts
• Weight: 8.0 lbs

General Pump 100719 Clutch w/Mounting Plate 47, 66 and 59(ES) Series, 12V, Single Groove. Mobile Clutch for 24mm Solid Shaft Pump

Features:
• Solid forged rotor. A one-piece solid forged rotor means no chance of internal parts separation. They have an even wall thickness around the coil which gives optimum flux distribution, maximizing torque.
• Different coil voltages available. 12 volt is the most common; 24 volt clutches are also available.
• High temperature, longer-life grease. Our special long-life grease has shown a significant improvement in life over other standard high temp greases.
• E-coating. Where possible, all parts in the clutch are e-coated to give maximum corrosion protection.
• High-temperature epoxy coil. To help prevent failure from vibration and outside contaminants, all coils are sealed in the coil shell with a high-temperature epoxy coating.
• Forged machined pulley. All GP models use a heavy-duty machined pulley. A stronger pulley resists damage

Data Sheet

Specifications:
• Pulley Size & Type: 7" - A Groove, 24mm Shaft
• Width: 2.25"
• Torque After Burnishing: 75 - 95 lbs.
• Power Requirement: 12V 47 Watts
• Weight: 8.0 lbs

General Pump 100720 Clutch w/Mounting Plate 44, 50, 63 and 58 (ES) Series, 12V, Single Groove. Mobile Clutch for 24mm Solid Shaft Pump

Features:
• Solid forged rotor. A one-piece solid forged rotor means no chance of internal parts separation. They have an even wall thickness around the coil which gives optimum flux distribution, maximizing torque.
• Different coil voltages available. 12 volt is the most common; 24 volt clutches are also available.
• High temperature, longer-life grease. Our special long-life grease has shown a significant improvement in life over other standard high temp greases.
• E-coating. Where possible, all parts in the clutch are e-coated to give maximum corrosion protection.
• High-temperature epoxy coil. To help prevent failure from vibration and outside contaminants, all coils are sealed in the coil shell with a high-temperature epoxy coating.
• Forged machined pulley. All GP models use a heavy-duty machined pulley. A stronger pulley resists damage

Data Sheet

Specifications:
• Pulley Size & Type: 7" - A Groove, 24mm Shaft
• Width: 2.25"
• Torque After Burnishing: 75 - 95 lbs.
• Power Requirement: 12V 47 Watts
• Weight: 8.0 lbs

General Pump 100719 Clutch w/Mounting Plate 47, 66 and 59(ES) Series, 24V, Dual Groove. Mobile Clutch for 24mm Solid Shaft Pump

Features:
• Solid forged rotor. A one-piece solid forged rotor means no chance of internal parts separation. They have an even wall thickness around the coil which gives optimum flux distribution, maximizing torque.
• Different coil voltages available. 12 volt is the most common; 24 volt clutches are also available.
• High temperature, longer-life grease. Our special long-life grease has shown a significant improvement in life over other standard high temp greases.
• E-coating. Where possible, all parts in the clutch are e-coated to give maximum corrosion protection.
• High-temperature epoxy coil. To help prevent failure from vibration and outside contaminants, all coils are sealed in the coil shell with a high-temperature epoxy coating.
• Forged machined pulley. All GP models use a heavy-duty machined pulley. A stronger pulley resists damage

Data Sheet

Specifications:
• Pulley Size & Type: 7" - A Groove, 24mm Shaft
• Width: 2.25"
• Torque After Burnishing: 75 - 95 lbs.
• Power Requirement: 24V 45.6 Watts
• Weight: 8.0 lbs

General Pump 100720 Clutch w/Mounting Plate 44, 50, 63 and 58 (ES) Series, 24V, Dual Groove. Mobile Clutch for 24mm Solid Shaft Pump

Features:
• Solid forged rotor. A one-piece solid forged rotor means no chance of internal parts separation. They have an even wall thickness around the coil which gives optimum flux distribution, maximizing torque.
• Different coil voltages available. 12 volt is the most common; 24 volt clutches are also available.
• High temperature, longer-life grease. Our special long-life grease has shown a significant improvement in life over other standard high temp greases.
• E-coating. Where possible, all parts in the clutch are e-coated to give maximum corrosion protection.
• High-temperature epoxy coil. To help prevent failure from vibration and outside contaminants, all coils are sealed in the coil shell with a high-temperature epoxy coating.
• Forged machined pulley. All GP models use a heavy-duty machined pulley. A stronger pulley resists damage

Data Sheet

Specifications:
• Pulley Size & Type: 7" - A Groove, 24mm Shaft
• Width: 2.25"
• Torque After Burnishing: 75 - 95 lbs.
• Power Requirement: 24V 45.6 Watts
• Weight: 8.0 lbs

General Pump Full Slide Hammer

Data Sheet

Specificatons:
• Used for General Pump Clutch Assemblies 100687, 100688, 100717, 100718, 100719, 100720
• Weight: 11.0 lbs

• Triplex Plunger Pump
• Direct Drive with Electric Flange NEMA 184C
• Max. Volume: 5.5 GPM
• Max. Discharge Pressure: 2,500 PSI
• Max. Pump Speed: 1750 RPM
• Shaft Diameter: 1 1/8” Hollow
• Max. Horsepower Requirements: 9.4 EBHP
• Max. Fluid Temp.: 165º degrees F.
• Inlet Ports (2): 1/2" BSP
• Discharge Ports (2): 3/8" BSP
• Drive Side: Standard right
• Forged brass head & valve covers
• Solid ceramic plungers
• Weight: 18.5 lb.

General Pump Clutch Centering Tool

Data Sheet

Specificatons:
• Used for General Pump Clutch Assemblies 100687, 100688, 100717, 100718, 100719, 100720
• 1/2"-13 Threaded Hole
• Use with 100163 Slide-hammer or bolt.
• Weight: lbs

General Pump Hose For Hammerhead DCFS 18 Surface Cleaners DCFSCP18 & DCFSCP18GZ

General Pump 2100463 Hose Guide Kit For DHRA50300

FEATURES
• Protects hose when pulled out or at an angle
• Durable powder coated steel construction
• Corrosion resistant stainless steel hardware
• 4-way enclosed pinch-proof stainless steel guides
• Use in tight locations where sharp edges may damage hos
• Durable powder coated

Instruction Manual

SPECIFICATIONS
• Works with DHRA50300 A Frame Hose Reels
• Color: Gray
• Hose Reel Not Included
• Weight 7.85 lbs

General Pump 2100503 Hose Guide Kit For DHRA50450

FEATURES
• Protects hose when pulled out or at an angle
• Durable powder coated steel construction
• Corrosion resistant stainless steel hardware
• 4-way enclosed pinch-proof stainless steel guides
• Use in tight locations where sharp edges may damage hos
• Durable powder coated

Instruction Manual

SPECIFICATIONS
• Works with DHRA50450 A Frame Hose Reels
• Color: Gray
• Hose Reel Not Included
• Weight 8.95 lbs

General Pump 2702000 Hose For Hammerhead Surface Cleaners DCFSCP20, DCFSCP20GZ, DCFSCS22Z & DCFSCP24GZ

General Pump 2100462 Hose Guide Kit For DHRA50150

FEATURES
• Protects hose when pulled out or at an angle
• Durable powder coated steel construction
• Corrosion resistant stainless steel hardware
• 4-way enclosed pinch-proof stainless steel guides
• Use in tight locations where sharp edges may damage hos
• Durable powder coated

Instruction Manual

SPECIFICATIONS
• Works with DHRA50150 A Frame Hose Reels
• Color: Gray
• Hose Reel Not Included
• Weight 7.15 lbs

General ZK1 Flow Unloader 3,600PSI, 3/8" BSP-F Inlet & 1/2" BSP-M

• Max. Pressure: 3,600 PSI
• Max. Volume: 2.3 - 10.8 GPM
• Adjustable pressure
• Brass body
• Max. Fluid Temp.: 165°
• Inlet: 3/8" BSP-F
• Outlet: 1/2" BSP-M
• Bypass: 1/2" BSP-M
• Gauge Port: 1/4" BSP-F
• Weight: 2.3 lbs.

4,200 PSI 4.0 GPM General EP1313G8U/IF Direct Drive Pump with built-in unloader and injector

Features:
• Features built-in unloader (U) or unloader and fixed injector (UIF)
• New Forged brass manifold, increases working pressure to 4,200 PSI
• New plunger guide bushing (patent pending)
• Solid ceramic plungers with dual guide system
• New dual diameter plunger guide
• New optimized outlet valves
• New dual lip oil seal
• 1” Hollow shaft, flanged for direct couple to gas engines (SAE J609B)

Data Sheet

Specifications:
• General EP1313G8UIF Pump with SAE J609 Gas Flange
• Max. Volume: 4.0 GPM
• Max. Discharge Pressure: 4,200 PSI
• Max. Pump Speed: 3,400 RPM
• Shaft Diameter: 1” Hollow
• Max. Horsepower Requirements: 14.5 GHP
• Max. Fluid Temp.: 165º F
• Oil Capacity: 15 oz.
• Inlet Port Thread: 1/2"-14 BSP-F
• Discharge Port Thread: 3/8"-19 BSP-M
• Dimensions: 11.2"x9.6"x7.6"
• Replaces TX1510G8UIA
• Weight: 15.9 lb

General HF25A 4,050 PSI 19.6 GPM Triplex Plunger Pump. A “New Generation” Pump

Features:
• A “New Generation” Pump
• Triplex Plunger Pump, available in 4 flows
• Patent-pending, symmetrical power end design featuring top and bottom mounting holes allowing for easy left to right shaft conversion
• Low-high pressure packing design with integrated cooling system
• • High volumetric efficiency suction/delivery valves featuring new spherical design of sealing areas
• Splash lubrication
• SAE-C hydraulic drive bell housing and flexible couplers available
• Available with external gear box (direct drive only)
• Optional pulsing capability using F10744201 lifting valve (not included)

Specifications Sheet

Materials:
• High resistance light alloy die cast crankcase
• 420 Stainless steel manifold, nickel treated
• Taper roller bearings
• Special anti-friction, forged, light alloy connecting rods
• Forged alloy steel crankshaft, hardened, tempered and nitrited
• Cast iron piston guide, nickel treated
• Solid ceramic plungers
• Stainless steel valves

Specifications:
• Maximum Inlet Pressure:. 45 PSI
• Maximum Fluid Temperature:. *140° F
• Inlet Port Thread:. 1” NPT-F
• Discharge Port Thread:. 3/4” NPT-F
• Shaft Diameter:. 1.575”/40 mm
• Stroke:. 1.969”/50 mm
• Pump Dimensions: . 20” x 14.5” x 9.4”
• Crankcase Oil Capacity:. 128.5 oz. (3.8 liters, use GP Series 220 Oil
• Ship via truck
• Weight: 132 lbs./60 kg

GP 2103245 Lock Pin Repair Kit for DHRA Hose Reels

Kit Includes:
• 2540085 Bracket, Lock x 1
• 2540086 Pin, Lock x 1
• 2720025 Spring, Lock Pin x 1
• 2200013 Washer, M8, SS x 1
• 2202033 Pin, Cotter, 2x20 x 1

GP 2103139 Brake Repair Kit for DHRA Hose Reels

Kit Includes:
• 2660268 Brake x 1
• 2200103 Bolt, M8 x 1
• 2660405 Knob, Brake x 1
• 2200013 Washer, M8, SS x 1