General Pump

General Pump 100687 Clutch w/Mounting Plate 47, 66 and 59(ES) Series, 12V, Dual Groove. Mobile Clutch for 24mm Solid Shaft Pump

Features:
• Solid forged rotor. A one-piece solid forged rotor means no chance of internal parts separation. They have an even wall thickness around the coil which gives optimum flux distribution, maximizing torque.
• Different coil voltages available. 12 volt is the most common; 24 volt clutches are also available.
• High temperature, longer-life grease. Our special long-life grease has shown a significant improvement in life over other standard high temp greases.
• E-coating. Where possible, all parts in the clutch are e-coated to give maximum corrosion protection.
• High-temperature epoxy coil. To help prevent failure from vibration and outside contaminants, all coils are sealed in the coil shell with a high-temperature epoxy coating.
• Forged machined pulley. All GP models use a heavy-duty machined pulley. A stronger pulley resists damage

Data Sheet

Specifications:
• Pulley Size & Type: 7" - A Groove, 24mm Shaft
• Width: 2.25"
• Torque After Burnishing: 75 - 95 lbs.
• Power Requirement: 12V 47 Watts
• Weight: 8.0 lbs

General Pump 100688 Clutch w/Mounting Plate 44, 50, 63 and 58 (ES) Series, 12V, Dual Groove. Mobile Clutch for 24mm Solid Shaft Pump

Features:
• Solid forged rotor. A one-piece solid forged rotor means no chance of internal parts separation. They have an even wall thickness around the coil which gives optimum flux distribution, maximizing torque.
• Different coil voltages available. 12 volt is the most common; 24 volt clutches are also available.
• High temperature, longer-life grease. Our special long-life grease has shown a significant improvement in life over other standard high temp greases.
• E-coating. Where possible, all parts in the clutch are e-coated to give maximum corrosion protection.
• High-temperature epoxy coil. To help prevent failure from vibration and outside contaminants, all coils are sealed in the coil shell with a high-temperature epoxy coating.
• Forged machined pulley. All GP models use a heavy-duty machined pulley. A stronger pulley resists damage

Data Sheet

Specifications:
• Pulley Size & Type: 7" - A Groove, 24mm Shaft
• Width: 2.25"
• Torque After Burnishing: 75 - 95 lbs.
• Power Requirement: 12V 47 Watts
• Weight: 8.0 lbs

General Pump 100719 Clutch w/Mounting Plate 47, 66 and 59(ES) Series, 12V, Single Groove. Mobile Clutch for 24mm Solid Shaft Pump

Features:
• Solid forged rotor. A one-piece solid forged rotor means no chance of internal parts separation. They have an even wall thickness around the coil which gives optimum flux distribution, maximizing torque.
• Different coil voltages available. 12 volt is the most common; 24 volt clutches are also available.
• High temperature, longer-life grease. Our special long-life grease has shown a significant improvement in life over other standard high temp greases.
• E-coating. Where possible, all parts in the clutch are e-coated to give maximum corrosion protection.
• High-temperature epoxy coil. To help prevent failure from vibration and outside contaminants, all coils are sealed in the coil shell with a high-temperature epoxy coating.
• Forged machined pulley. All GP models use a heavy-duty machined pulley. A stronger pulley resists damage

Data Sheet

Specifications:
• Pulley Size & Type: 7" - A Groove, 24mm Shaft
• Width: 2.25"
• Torque After Burnishing: 75 - 95 lbs.
• Power Requirement: 12V 47 Watts
• Weight: 8.0 lbs

General Pump 100720 Clutch w/Mounting Plate 44, 50, 63 and 58 (ES) Series, 12V, Single Groove. Mobile Clutch for 24mm Solid Shaft Pump

Features:
• Solid forged rotor. A one-piece solid forged rotor means no chance of internal parts separation. They have an even wall thickness around the coil which gives optimum flux distribution, maximizing torque.
• Different coil voltages available. 12 volt is the most common; 24 volt clutches are also available.
• High temperature, longer-life grease. Our special long-life grease has shown a significant improvement in life over other standard high temp greases.
• E-coating. Where possible, all parts in the clutch are e-coated to give maximum corrosion protection.
• High-temperature epoxy coil. To help prevent failure from vibration and outside contaminants, all coils are sealed in the coil shell with a high-temperature epoxy coating.
• Forged machined pulley. All GP models use a heavy-duty machined pulley. A stronger pulley resists damage

Data Sheet

Specifications:
• Pulley Size & Type: 7" - A Groove, 24mm Shaft
• Width: 2.25"
• Torque After Burnishing: 75 - 95 lbs.
• Power Requirement: 12V 47 Watts
• Weight: 8.0 lbs

General Pump 100719 Clutch w/Mounting Plate 47, 66 and 59(ES) Series, 24V, Dual Groove. Mobile Clutch for 24mm Solid Shaft Pump

Features:
• Solid forged rotor. A one-piece solid forged rotor means no chance of internal parts separation. They have an even wall thickness around the coil which gives optimum flux distribution, maximizing torque.
• Different coil voltages available. 12 volt is the most common; 24 volt clutches are also available.
• High temperature, longer-life grease. Our special long-life grease has shown a significant improvement in life over other standard high temp greases.
• E-coating. Where possible, all parts in the clutch are e-coated to give maximum corrosion protection.
• High-temperature epoxy coil. To help prevent failure from vibration and outside contaminants, all coils are sealed in the coil shell with a high-temperature epoxy coating.
• Forged machined pulley. All GP models use a heavy-duty machined pulley. A stronger pulley resists damage

Data Sheet

Specifications:
• Pulley Size & Type: 7" - A Groove, 24mm Shaft
• Width: 2.25"
• Torque After Burnishing: 75 - 95 lbs.
• Power Requirement: 24V 45.6 Watts
• Weight: 8.0 lbs

General Pump 100720 Clutch w/Mounting Plate 44, 50, 63 and 58 (ES) Series, 24V, Dual Groove. Mobile Clutch for 24mm Solid Shaft Pump

Features:
• Solid forged rotor. A one-piece solid forged rotor means no chance of internal parts separation. They have an even wall thickness around the coil which gives optimum flux distribution, maximizing torque.
• Different coil voltages available. 12 volt is the most common; 24 volt clutches are also available.
• High temperature, longer-life grease. Our special long-life grease has shown a significant improvement in life over other standard high temp greases.
• E-coating. Where possible, all parts in the clutch are e-coated to give maximum corrosion protection.
• High-temperature epoxy coil. To help prevent failure from vibration and outside contaminants, all coils are sealed in the coil shell with a high-temperature epoxy coating.
• Forged machined pulley. All GP models use a heavy-duty machined pulley. A stronger pulley resists damage

Data Sheet

Specifications:
• Pulley Size & Type: 7" - A Groove, 24mm Shaft
• Width: 2.25"
• Torque After Burnishing: 75 - 95 lbs.
• Power Requirement: 24V 45.6 Watts
• Weight: 8.0 lbs

General Pump Full Slide Hammer

Data Sheet

Specificatons:
• Used for General Pump Clutch Assemblies 100687, 100688, 100717, 100718, 100719, 100720
• Use with 520297m clutch centering tool
• Weight: 11.0 lbs

• Triplex Plunger Pump
• Direct Drive with Electric Flange NEMA 184C
• Max. Volume: 5.5 GPM
• Max. Discharge Pressure: 2,500 PSI
• Max. Pump Speed: 1750 RPM
• Shaft Diameter: 1 1/8” Hollow
• Max. Horsepower Requirements: 9.4 EBHP
• Max. Fluid Temp.: 165º degrees F.
• Inlet Ports (2): 1/2" BSP
• Discharge Ports (2): 3/8" BSP
• Drive Side: Standard right
• Forged brass head & valve covers
• Solid ceramic plungers
• Weight: 18.5 lb.

General Pump Clutch Centering Tool

Data Sheet

Specificatons:
• Used for General Pump Clutch Assemblies 100687, 100688, 100717, 100718, 100719, 100720
• 1/2"-13 Threaded Hole
• Use with 100163 Slide-hammer or bolt.
• Weight: lbs

General Pump Hose For Hammerhead DCFS 18 Surface Cleaners DCFSCP18 & DCFSCP18GZ

General Pump 2100463 Hose Guide Kit For DHRA50300

FEATURES
• Protects hose when pulled out or at an angle
• Durable powder coated steel construction
• Corrosion resistant stainless steel hardware
• 4-way enclosed pinch-proof stainless steel guides
• Use in tight locations where sharp edges may damage hos
• Durable powder coated

Instruction Manual

SPECIFICATIONS
• Works with DHRA50300 A Frame Hose Reels
• Color: Gray
• Hose Reel Not Included
• Weight 7.85 lbs

General Pump 2100503 Hose Guide Kit For DHRA50450

FEATURES
• Protects hose when pulled out or at an angle
• Durable powder coated steel construction
• Corrosion resistant stainless steel hardware
• 4-way enclosed pinch-proof stainless steel guides
• Use in tight locations where sharp edges may damage hos
• Durable powder coated

Instruction Manual

SPECIFICATIONS
• Works with DHRA50450 A Frame Hose Reels
• Color: Gray
• Hose Reel Not Included
• Weight 8.95 lbs

General Pump 2702000 Hose For Hammerhead Surface Cleaners DCFSCP20, DCFSCP20GZ, DCFSCS22Z & DCFSCP24GZ

General Pump 2100462 Hose Guide Kit For DHRA50150

FEATURES
• Protects hose when pulled out or at an angle
• Durable powder coated steel construction
• Corrosion resistant stainless steel hardware
• 4-way enclosed pinch-proof stainless steel guides
• Use in tight locations where sharp edges may damage hos
• Durable powder coated

Instruction Manual

SPECIFICATIONS
• Works with DHRA50150 A Frame Hose Reels
• Color: Gray
• Hose Reel Not Included
• Weight 7.15 lbs

General ZK1 Flow Unloader 3,600PSI, 3/8" BSP-F Inlet & 1/2" BSP-M

• Max. Pressure: 3,600 PSI
• Max. Volume: 2.3 - 10.8 GPM
• Adjustable pressure
• Brass body
• Max. Fluid Temp.: 165°
• Inlet: 3/8" BSP-F
• Outlet: 1/2" BSP-M
• Bypass: 1/2" BSP-M
• Gauge Port: 1/4" BSP-F
• Weight: 2.3 lbs.

4,200 PSI 4.0 GPM General EP1313G8U/IF Direct Drive Pump with built-in unloader and injector

Features:
• Features built-in unloader (U) or unloader and fixed injector (UIF)
• New Forged brass manifold, increases working pressure to 4,200 PSI
• New plunger guide bushing (patent pending)
• Solid ceramic plungers with dual guide system
• New dual diameter plunger guide
• New optimized outlet valves
• New dual lip oil seal
• 1” Hollow shaft, flanged for direct couple to gas engines (SAE J609B)

Data Sheet

Specifications:
• General EP1313G8UIF Pump with SAE J609 Gas Flange
• Max. Volume: 4.0 GPM
• Max. Discharge Pressure: 4,200 PSI
• Max. Pump Speed: 3,400 RPM
• Shaft Diameter: 1” Hollow
• Max. Horsepower Requirements: 14.5 GHP
• Max. Fluid Temp.: 165º F
• Oil Capacity: 15 oz.
• Inlet Port Thread: 1/2"-14 BSP-F
• Discharge Port Thread: 3/8"-19 BSP-M
• Dimensions: 11.2"x9.6"x7.6"
• Replaces TX1510G8UIA
• Weight: 15.9 lb

General HF25A 4,050 PSI 19.6 GPM Triplex Plunger Pump. A “New Generation” Pump

Features:
• A “New Generation” Pump
• Triplex Plunger Pump, available in 4 flows
• Patent-pending, symmetrical power end design featuring top and bottom mounting holes allowing for easy left to right shaft conversion
• Low-high pressure packing design with integrated cooling system
• • High volumetric efficiency suction/delivery valves featuring new spherical design of sealing areas
• Splash lubrication
• SAE-C hydraulic drive bell housing and flexible couplers available
• Available with external gear box (direct drive only)
• Optional pulsing capability using F10744201 lifting valve (not included)

Specifications Sheet

Materials:
• High resistance light alloy die cast crankcase
• 420 Stainless steel manifold, nickel treated
• Taper roller bearings
• Special anti-friction, forged, light alloy connecting rods
• Forged alloy steel crankshaft, hardened, tempered and nitrited
• Cast iron piston guide, nickel treated
• Solid ceramic plungers
• Stainless steel valves

Specifications:
• Maximum Inlet Pressure:. 45 PSI
• Maximum Fluid Temperature:. *140° F
• Inlet Port Thread:. 1” NPT-F
• Discharge Port Thread:. 3/4” NPT-F
• Shaft Diameter:. 1.575”/40 mm
• Stroke:. 1.969”/50 mm
• Pump Dimensions: . 20” x 14.5” x 9.4”
• Crankcase Oil Capacity:. 128.5 oz. (3.8 liters, use GP Series 220 Oil
• Ship via truck
• Weight: 132 lbs./60 kg

GP 2103245 Lock Pin Repair Kit for DHRA Hose Reels

Kit Includes:
• 2540085 Bracket, Lock x 1
• 2540086 Pin, Lock x 1
• 2720025 Spring, Lock Pin x 1
• 2200013 Washer, M8, SS x 1
• 2202033 Pin, Cotter, 2x20 x 1

GP 2103139 Brake Repair Kit for DHRA Hose Reels

Kit Includes:
• 2660268 Brake x 1
• 2200103 Bolt, M8 x 1
• 2660405 Knob, Brake x 1
• 2200013 Washer, M8, SS x 1

GP Hose Reel Swivel 5,000 PSI Forged Brass DHR (New Style)

Compatible with DHR50100, DHR50150 & DHRHC50100 hose reels