Suttner America

Suttner ST-230 Safety Relief Valve 3,600 PSI New Design with Tamper Proof Cap. Ideal in-line regulator for multi-gun pumping units on se!f-serve car wash systems. Perfect for pressure washer/steam combination applications and carpet cleaning industry

Features:
• Newly designed - Small holes in the cap and body so a tamper proof wire can be put through them like shown in the 3rd photo
• Adjustable pressure
• Forged brass housing, stainless steel ball and valve seat
• Special seals for maximum heat and chemical resistance
• Valve member rides on elastomeric cushion, eliminating metal to metal contact, a common cause of regulator failure
• Quickly re-buildable with repair kit. Can be rebuilt without removing from the installation

Specifications:
• Pressure: 500 - 3,500 PSI
• Flow Rate: 8 GPM
• O-Ring: EPDM
• Max Temperature: 200° F
• Inlet: 1/4" FNPT
• Outlet: 1/4” FNPT
• Note: Tamper proof wire and seal are not included
• Weight: 1.10 lbs

Suttner Stainless Steel Hose Hanger, Holds 120' of 1/2" hose. This food grade hose hanger is ideal for mounting to any vertical wall

Specifications:
• Polished stainless steel
• Food Grade
• Holds 175 ft of 3/8” hose
• Holds 120 ft of 1/2” hose
• Holds 90 ft of 3/4” hose
• Dimensions: 14-1/4” x 6-5/16” x 7-3/4”
• Weight: 2.0 lbs.

Suttner ST-175 Stainless Steel 24” Foam & Rinse Lance 5,000 PSI with 1/4" F Inlet. Switch from foam to rinse by turning the valve that’s conveniently within hands reach

Features
• The change-over lance ST-175 Foam & Clean is the ideal accessory for Suttner's foam injector line. The innovative change-over technology allows to direct the full flow into either one or the other outlet pipe just by turning the hand wheel at the inlet
• In one position of the hand wheel the flow is directed thru an ST-75 foam head for foaming. After changing over the full flow is directed thru the other pipe and a regular spray nozzle for rinsing
• Appropriate nozzle sizing at chemical injector and ST-175 allows changing from foaming to rinsing right at the lance. ST -175 Foam & Clean is compatible to ST-160 / ST-160M / ST-164 / ST-166 / ST-167
• Due to ST-175's changeable air injector nozzles the lance can be driven with all pressure washers with flow rates from 1 to 6 GPM. Nozzles with integrated jet former are required

ST-175 Foam & Rinse Lance on YouTube

Specifications
• Flow Rate: 1.0 – 6.0 GPM
• Max Pressure: 5,000 PSI
• Length: 24.0”
• Max Temp: 140° F.
• Inlet: 1/4" Female NPT
• Outlet (Foam): ST-75 Foam head (Air Injector Nozzle not included)
• Outlet (Rinse): 1/4" FPT with nozzle protector (1/4” MPT high pressure nozzle not included)
• Note: Suttner ST-160, ST-160M or St-164 Chemical or Foam injector, air injector nozzle and 1/4" MPT nozzle required and are not included
• Weight: 2.70 lb

Please use Nozzle Chart to determine proper spray nozzle size

Nozzle Chart

Use Spray Nozzle Size and Foam Nozzle Chart to determine correct Air Injector Nozzle to use

Foam Nozzle Chart

Suttner M5 Nozzle Insert 1.0 mm, #0237. Nozzle inserts for sewer cleaning nozzles and nozzle driver

Specifications:
• Max Pressure: 7,250 PSI
• Hole: 1.0 mm
• Nozzle Size: # 0237
• Allen Key: 2.5 mm Hex
• Material: Hardened stainless steel

Suttner ST-3225 Ergonomic Inline Food Grade Spray Gun 31.5 GPM. Professional hp gun with progressive closing system. Stainless steel. Field of application: foam and rinsing applications in the food industry, etc. The ergonomic design of the ST-3225 helps reduce fatigue

Features
• The professional spray gun for the food industry
• Especially designed for highest requirements to hygiene and ergonomics
• The internal components are made from stainless steel and the outer body made out of plastics intended to come into contact with foodstuffs
• Suitable for a high flow of 31.5 GPM
• Progressive closing system by an integrated damper
• LTF technology: 90 % reduced holding force and 40 % reduced trigger force against usual market guns
• Very low pressure drop
• Food Grade

See ST-3225 in action on YouTube

Specifications
• Max Flow: 31.5 GPM
• Max Pressure: 870 PSI
• Max Temp: 212° F.
• Inlet: 1/2" Female Swivel
• Outlet: 1/2" Female
• Weight: 1.64 lb

Suttner ST-230 Safety Relief Valve 1,500 PSI. Ideal in-line regulator for multi-gun pumping units on se!f-serve car wash systems. Perfect for pressure washer/steam combination applications and carpet cleaning industry

Features:
• Adjustable pressure
• Forged brass housing, stainless steel ball and valve seat
• Special seals for maximum heat and chemical resistance
• Valve member rides on elastomeric cushion, eliminating metal to metal contact, a common cause of regulator failure
• Quickly re-buildable with repair kit. Can be rebuilt without removing from the installation

Specifications:
• Pressure: 145 - 1,500 PSI
• Flow Rate: 8 GPM
• O-Ring: EPDM
• Max Temperature: 200° F
• Inlet: 1/4" FNPT
• Outlet: 1/4” FNPT
• Weight: 0.84 lbs

1” Suttner #75.0 ST-49 Milling Sewer Cleaning Nozzle. With 3 Front and 9 Rear jets and rated to 3,625 PSI

Features:
• High Quality, German engineered components
• With its 3 very strong concentrated forward jets and the sharp cutting edges the milling type nozzles will tear through almost any kind of blockage
• The sharp edges cut, break and penetrate through every kind of blockage
• Made out of wear-resistant, hardened stainless steel
• Centric jet is plugged
• 3 Lateral front jets with nozzle inserts
• 9 Rear jets with nozzle inserts
• Nozzle is equipped with replaceable hardened stainless steel nozzle inserts
• Due to this feature the efficiency is considerably higher compared with those nozzles with drilled holes and the service life is several times longer

Applications:
• Penetration of completely clogged pipes
• Opening of root masses
• Opening of frozen pipelines
• Hydraulic thrust boring flushing operations

Specifications:
• Nozzle Size: # 75.0
• Material: Stainless steel
• Maximum Pressure: 3,625 PSI
• Inlet: 1” Female
• Outside Diameter (O.D.): 1.96”
• Weight: 19.20 oz

Please use Nozzle Chart to determine proper nozzle size

Nozzle Chart

3/4” Suttner #40.0 ST-49 Milling Sewer Cleaning Nozzle. With 3 Front and 6 Rear jets and rated to 3,625 PSI

Features:
• High Quality, German engineered components
• With its 3 very strong concentrated forward jets and the sharp cutting edges the milling type nozzles will tear through almost any kind of blockage
• The sharp edges cut, break and penetrate through every kind of blockage
• Made out of wear-resistant, hardened stainless steel
• Centric jet is plugged
• 3 Lateral front jets with nozzle inserts
• 6 Rear jets with nozzle inserts
• Nozzle is equipped with replaceable hardened stainless steel nozzle inserts
• Due to this feature the efficiency is considerably higher compared with those nozzles with drilled holes and the service life is several times longer

Applications:
• Penetration of completely clogged pipes
• Opening of root masses
• Opening of frozen pipelines
• Hydraulic thrust boring flushing operations

Specifications:
• Nozzle Size: # 40.0
• Material: Stainless steel
• Maximum Pressure: 3,625 PSI
• Inlet: 3/4” Female
• Outside Diameter (O.D.): 1.50”
• Weight: 12.45 oz

Please use Nozzle Chart to determine proper nozzle size

Nozzle Chart

1/2” Suttner #31.0 ST-49 Milling Sewer Cleaning Nozzle. With 3 Front and 6 Rear jets and rated to 5,076 PSI

Features:
• High Quality, German engineered components
• With its 3 very strong concentrated forward jets and the sharp cutting edges the milling type nozzles will tear through almost any kind of blockage
• The sharp edges cut, break and penetrate through every kind of blockage
• Made out of wear-resistant, hardened stainless steel
• Centric jet is plugged
• 3 Lateral front jets with nozzle inserts
• 6 Rear jets with nozzle inserts
• Nozzle is equipped with replaceable hardened stainless steel nozzle inserts
• Due to this feature the efficiency is considerably higher compared with those nozzles with drilled holes and the service life is several times longer

Applications:
• Penetration of completely clogged pipes
• Opening of root masses
• Opening of frozen pipelines
• Hydraulic thrust boring flushing operations

Specifications:
• Nozzle Size: # 31.0
• Material: Stainless steel
• Maximum Pressure: 5,076 PSI
• Inlet: 1/2” Female
• Outside Diameter (O.D.): 1.23”
• Weight: 5.7 oz

Please use Nozzle Chart to determine proper nozzle size

Nozzle Chart

1/2” Suttner #20.0 ST-49 Milling Sewer Cleaning Nozzle. With 3 Front and 6 Rear jets and rated to 5,076 PSI

Features:
• High Quality, German engineered components
• With its 3 very strong concentrated forward jets and the sharp cutting edges the milling type nozzles will tear through almost any kind of blockage
• The sharp edges cut, break and penetrate through every kind of blockage
• Made out of wear-resistant, hardened stainless steel
• Centric jet is plugged
• 3 Lateral front jets with nozzle inserts
• 6 Rear jets with nozzle inserts
• Nozzle is equipped with replaceable hardened stainless steel nozzle inserts
• Due to this feature the efficiency is considerably higher compared with those nozzles with drilled holes and the service life is several times longer

Applications:
• Penetration of completely clogged pipes
• Opening of root masses
• Opening of frozen pipelines
• Hydraulic thrust boring flushing operations

Specifications:
• Nozzle Size: # 20.0
• Material: Stainless steel
• Maximum Pressure: 5,076 PSI
• Inlet: 1/2” Female
• Outside Diameter (O.D.): 1.23”
• Weight: 5.7 oz

Please use Nozzle Chart to determine proper nozzle size

Nozzle Chart

1/2” Suttner #12.0 ST-49 Milling Sewer Cleaning Nozzle. With 3 Front and 6 Rear jets and rated to 5,076 PSI

Features:
• High Quality, German engineered components
• With its 3 very strong concentrated forward jets and the sharp cutting edges the milling type nozzles will tear through almost any kind of blockage
• The sharp edges cut, break and penetrate through every kind of blockage
• Made out of wear-resistant, hardened stainless steel
• Centric jet is plugged
• 3 Lateral front jets with nozzle inserts
• 6 Rear jets with nozzle inserts
• Nozzle is equipped with replaceable hardened stainless steel nozzle inserts
• Due to this feature the efficiency is considerably higher compared with those nozzles with drilled holes and the service life is several times longer

Applications:
• Penetration of completely clogged pipes
• Opening of root masses
• Opening of frozen pipelines
• Hydraulic thrust boring flushing operations

Specifications:
• Nozzle Size: # 12.0
• Material: Stainless steel
• Maximum Pressure: 5,076 PSI
• Inlet: 1/2” Female
• Outside Diameter (O.D.): 1.23”
• Weight: 5.7 oz

Please use Nozzle Chart to determine proper nozzle size

Nozzle Chart

3/8” Suttner #20.0 ST-49 Milling Sewer Cleaning Nozzle. With 3 Front and 6 Rear jets and rated to 5,076 PSI

Features:
• High Quality, German engineered components
• With its 3 very strong concentrated forward jets and the sharp cutting edges the milling type nozzles will tear through almost any kind of blockage
• The sharp edges cut, break and penetrate through every kind of blockage
• Made out of wear-resistant, hardened stainless steel
• Centric jet is plugged
• 3 Lateral front jets with nozzle inserts
• 6 Rear jets with nozzle inserts
• Nozzle is equipped with replaceable hardened stainless steel nozzle inserts
• Due to this feature the efficiency is considerably higher compared with those nozzles with drilled holes and the service life is several times longer

Applications:
• Penetration of completely clogged pipes
• Opening of root masses
• Opening of frozen pipelines
• Hydraulic thrust boring flushing operations

Specifications:
• Nozzle Size: # 20.0
• Material: Stainless steel
• Maximum Pressure: 5,076 PSI
• Inlet: 3/8” Female
• Outside Diameter (O.D.): 1.11”
• Weight: 4.0 oz

Please use Nozzle Chart to determine proper nozzle size

Nozzle Chart

3/8” Suttner #12.0 ST-49 Milling Sewer Cleaning Nozzle. With 3 Front and 6 Rear jets and rated to 5,076 PSI

Features:
• High Quality, German engineered components
• With its 3 very strong concentrated forward jets and the sharp cutting edges the milling type nozzles will tear through almost any kind of blockage
• The sharp edges cut, break and penetrate through every kind of blockage
• Made out of wear-resistant, hardened stainless steel
• Centric jet is plugged
• 3 Lateral front jets with nozzle inserts
• 6 Rear jets with nozzle inserts
• Nozzle is equipped with replaceable hardened stainless steel nozzle inserts
• Due to this feature the efficiency is considerably higher compared with those nozzles with drilled holes and the service life is several times longer

Applications:
• Penetration of completely clogged pipes
• Opening of root masses
• Opening of frozen pipelines
• Hydraulic thrust boring flushing operations

Specifications:
• Nozzle Size: # 12.0
• Material: Stainless steel
• Maximum Pressure: 5,076 PSI
• Inlet: 3/8” Female
• Outside Diameter (O.D.): 1.11”
• Weight: 4.0 oz

Please use Nozzle Chart to determine proper nozzle size

Nozzle Chart

3/8” Suttner #10.0 ST-49 Milling Sewer Cleaning Nozzle. With 3 Front and 6 Rear jets and rated to 5,076 PSI

Features:
• High Quality, German engineered components
• With its 3 very strong concentrated forward jets and the sharp cutting edges the milling type nozzles will tear through almost any kind of blockage
• The sharp edges cut, break and penetrate through every kind of blockage
• Made out of wear-resistant, hardened stainless steel
• Centric jet is plugged
• 3 Lateral front jets with nozzle inserts
• 6 Rear jets with nozzle inserts
• Nozzle is equipped with replaceable hardened stainless steel nozzle inserts
• Due to this feature the efficiency is considerably higher compared with those nozzles with drilled holes and the service life is several times longer

Applications:
• Penetration of completely clogged pipes
• Opening of root masses
• Opening of frozen pipelines
• Hydraulic thrust boring flushing operations

Specifications:
• Nozzle Size: # 10.0
• Material: Stainless steel
• Maximum Pressure: 5,076 PSI
• Inlet: 3/8” Female
• Outside Diameter (O.D.): 1.11”
• Weight: 4.0 oz

Please use Nozzle Chart to determine proper nozzle size

Nozzle Chart

3/8” Suttner #8.0 ST-49 Milling Sewer Cleaning Nozzle. With 3 Front and 6 Rear jets and rated to 5,076 PSI

Features:
• High Quality, German engineered components
• With its 3 very strong concentrated forward jets and the sharp cutting edges the milling type nozzles will tear through almost any kind of blockage
• The sharp edges cut, break and penetrate through every kind of blockage
• Made out of wear-resistant, hardened stainless steel
• Centric jet is plugged
• 3 Lateral front jets with nozzle inserts
• 6 Rear jets with nozzle inserts
• Nozzle is equipped with replaceable hardened stainless steel nozzle inserts
• Due to this feature the efficiency is considerably higher compared with those nozzles with drilled holes and the service life is several times longer

Applications:
• Penetration of completely clogged pipes
• Opening of root masses
• Opening of frozen pipelines
• Hydraulic thrust boring flushing operations

Specifications:
• Nozzle Size: # 8.0
• Material: Stainless steel
• Maximum Pressure: 5,076 PSI
• Inlet: 3/8” Female
• Outside Diameter (O.D.): 1.11”
• Weight: 4.0 oz

Please use Nozzle Chart to determine proper nozzle size

Nozzle Chart

3/8” Suttner #7.0 ST-49 Milling Sewer Cleaning Nozzle. With 3 Front and 6 Rear jets and rated to 5,076 PSI

Features:
• High Quality, German engineered components
• With its 3 very strong concentrated forward jets and the sharp cutting edges the milling type nozzles will tear through almost any kind of blockage
• The sharp edges cut, break and penetrate through every kind of blockage
• Made out of wear-resistant, hardened stainless steel
• Centric jet is plugged
• 3 Lateral front jets with nozzle inserts
• 6 Rear jets with nozzle inserts
• Nozzle is equipped with replaceable hardened stainless steel nozzle inserts
• Due to this feature the efficiency is considerably higher compared with those nozzles with drilled holes and the service life is several times longer

Applications:
• Penetration of completely clogged pipes
• Opening of root masses
• Opening of frozen pipelines
• Hydraulic thrust boring flushing operations

Specifications:
• Nozzle Size: # 7.0
• Material: Stainless steel
• Maximum Pressure: 5,076 PSI
• Inlet: 3/8” Female
• Outside Diameter (O.D.): 1.11”
• Weight: 4.0 oz

Please use Nozzle Chart to determine proper nozzle size

Nozzle Chart

1/4” Suttner #12.0 ST-49 Milling Sewer Cleaning Nozzle. With 3 Front and 4 Rear jets and rated to 5,076 PSI

Features:
• High Quality, German engineered components
• With its 3 very strong concentrated forward jets and the sharp cutting edges the milling type nozzles will tear through almost any kind of blockage
• The sharp edges cut, break and penetrate through every kind of blockage
• Made out of wear-resistant, hardened stainless steel
• Centric jet is plugged
• 3 Lateral front jets 0.5 mm drilled
• 4 Rear jets with nozzle inserts
• Nozzle is equipped with replaceable hardened stainless steel centric front and rear jets
• Due to this feature the efficiency is considerably higher compared with those nozzles with drilled holes and the service life is several times longer

Applications:
• Penetration of completely clogged pipes
• Opening of root masses
• Opening of frozen pipelines
• Hydraulic thrust boring flushing operations

Specifications:
• Nozzle Size: # 12.0
• Material: Stainless steel
• Maximum Pressure: 5,076 PSI
• Inlet: 1/4” Female
• Outside Diameter (O.D.): .95”
• Weight: 2.8 oz

Please use Nozzle Chart to determine proper nozzle size

Nozzle Chart

1/4” Suttner #10.0 ST-49 Milling Sewer Cleaning Nozzle. With 3 Front and 4 Rear jets and rated to 5,076 PSI

Features:
• High Quality, German engineered components
• With its 3 very strong concentrated forward jets and the sharp cutting edges the milling type nozzles will tear through almost any kind of blockage
• The sharp edges cut, break and penetrate through every kind of blockage
• Made out of wear-resistant, hardened stainless steel
• Centric jet is plugged
• 3 Lateral front jets 0.5 mm drilled
• 4 Rear jets with nozzle inserts
• Nozzle is equipped with replaceable hardened stainless steel centric front and rear jets
• Due to this feature the efficiency is considerably higher compared with those nozzles with drilled holes and the service life is several times longer

Applications:
• Penetration of completely clogged pipes
• Opening of root masses
• Opening of frozen pipelines
• Hydraulic thrust boring flushing operations

Specifications:
• Nozzle Size: # 10.0
• Material: Stainless steel
• Maximum Pressure: 5,076 PSI
• Inlet: 1/4” Female
• Outside Diameter (O.D.): .95”
• Weight: 2.8 oz

Please use Nozzle Chart to determine proper nozzle size

Nozzle Chart

1/4” Suttner #8.0 ST-49 Milling Sewer Cleaning Nozzle. With 3 Front and 4 Rear jets and rated to 5,076 PSI

Features:
• High Quality, German engineered components
• With its 3 very strong concentrated forward jets and the sharp cutting edges the milling type nozzles will tear through almost any kind of blockage
• The sharp edges cut, break and penetrate through every kind of blockage
• Made out of wear-resistant, hardened stainless steel
• Centric jet is plugged
• 3 Lateral front jets 0.5 mm drilled
• 4 Rear jets with nozzle inserts
• Nozzle is equipped with replaceable hardened stainless steel centric front and rear jets
• Due to this feature the efficiency is considerably higher compared with those nozzles with drilled holes and the service life is several times longer

Applications:
• Penetration of completely clogged pipes
• Opening of root masses
• Opening of frozen pipelines
• Hydraulic thrust boring flushing operations

Specifications:
• Nozzle Size: # 8.0
• Material: Stainless steel
• Maximum Pressure: 5,076 PSI
• Inlet: 1/4” Female
• Outside Diameter (O.D.): .95”
• Weight: 2.8 oz

Please use Nozzle Chart to determine proper nozzle size

Nozzle Chart