Fairview USA Inc.

Fairview GAS-FLO™ CP-2020 1/4” OD x 20” Short Nose POL x Short Nose POL Copper Propane Gas Pigtail. Fairview's Short POL To Short POL Copper pigtails are ideal for use with Propane Gas

Applications:
• Propane gas copper pigtails and hogtails provide a flexible connection between the container valve and the regulator
• Solder connections Copper tube for PIGTAILS is 1/4" O.D. by .049 WALL
• Usage depends on application and requirements
• With soldered ends and a wide selection of connections and lengths

TECHNICAL DATA SHEET

INSTALLATION DATA SHEET

Specifications:
• Tube OD: 1/4”
• Approx. Length: 20”
• Tube Material: Copper
• End: Short Nose P.O.L
• End: Short Nose P.O.L
• TO BE INSTALLED BY LICENSED GAS FITTERS ONLY
• Weight: 0.50 lbs

Fairview GAS-FLO® GR-630B Single Stage Hi-Pressure RV Camper LP / Propane Gas Regulator 1/4 FPT 500,000 BTU/HR. This Fairview's GAS-FLO® High Pressure LP Regulator has outlet setting 30 PSIG

Applications:
• Ideally suited for applications where pounds instead of inches of w.c. are required
• Factory pre-set 30 PSIG
• Used on Gas Grills, Smokers and Fish Cookers
• UL Listed

TECHNICAL DATA SHEET

Specifications:
• Inlet: 1/4 FPT
• Outlet: 1/4 FPT
• Outlet Pressure (Set Point): 30 PSIG
• Inlet Pressure: 100 PSIG
• Capacity At 10% Droop from set point BTU/Hr: 500,000
• TO BE INSTALLED BY LICENSED GAS FITTERS ONLY
• Weight: 0.45 lbs

Fairview GAS-FLO™ 2003-T Excess Flow Tailpiece Assembly with O-Ring POL x 1/4 MPT. Fairview's Excess Flow Tailpiece Assembly is ideal for LP-Gas applications

Specifications:
• POL: Excess Flow with O-ring
• Thread: 1/4 MPT
• O.A.L: 2-3/8”
• Material: Brass
• TO BE INSTALLED BY LICENSED GAS FITTERS ONLY
• Weight: 3.7 oz

Fairview GAS-FLO™ CP-2012 1/4” OD x 12” Short Nose POL x Short Nose POL Copper Propane Gas Pigtail. Fairview's Short POL To Short POL Copper pigtails are ideal for use with Propane Gas

Applications:
• Propane gas copper pigtails and hogtails provide a flexible connection between the container valve and the regulator
• Solder connections Copper tube for PIGTAILS is 1/4" O.D. by .049 WALL
• Usage depends on application and requirements
• With soldered ends and a wide selection of connections and lengths

TECHNICAL DATA SHEET

INSTALLATION DATA SHEET

Specifications:
• Tube OD: 1/4”
• Approx. Length: 12”
• Tube Material: Copper
• End: Short Nose P.O.L
• End: Short Nose P.O.L
• TO BE INSTALLED BY LICENSED GAS FITTERS ONLY
• Weight: 0.40 lbs

Fairview GAS-FLO™ 1/4” ID x 72” AOL Type 1 Thermoplastic Propane Hose Assembly with 3/8” 45° SAE Female Swivel Flare x 3/8” 45° SAE Female Swivel Flare Fittings. Fairview's Type 1 Thermoplastic F.SAE Assemblies are CSA Certified to 350 PSI WP -40°F To 140°F

Applications:
• Used To Conduct Natural Gas In A Gaseous State And Propane In Either A Liquid Or Gaseous State Up To 350 P.S.I
• UL/CSA Approved Type 1 Propane/Nat Gas Assy (Type 1 Assy)

TECHNICAL DATA SHEET

Specifications:
• Hose ID: 1/4”
• Assembly Overall Length: 72” (Tolerance ±1% of length measured to the nearest 1/8 of an inch)
• Temperature: -40°F to +140°F
• Color: Black
• Max Pressure: 350 PSI
• End: 3/8” Brass 45° SAE Female Swivel Flare
• End: 3/8” Brass 45° SAE Female Swivel Flare
• TO BE INSTALLED BY LICENSED GAS FITTERS ONLY
• Weight: 0.65 lbs

Fairview GAS-FLO™ 1/4” ID x 36” AOL Type 1 Thermoplastic Propane Hose Assembly with 3/8” 45° SAE Female Swivel Flare x 3/8” 45° SAE Female Swivel Flare Fittings. Fairview's Type 1 Thermoplastic F.SAE Assemblies are CSA Certified to 350 PSI WP -40°F To 140°F

Applications:
• Used To Conduct Natural Gas In A Gaseous State And Propane In Either A Liquid Or Gaseous State Up To 350 P.S.I
• UL/CSA Approved Type 1 Propane/Nat Gas Assy (Type 1 Assy)

TECHNICAL DATA SHEET

Specifications:
• Hose ID: 1/4”
• Assembly Overall Length: 36” (Tolerance ± 1/4 of an inch)
• Temperature: -40°F to +140°F
• Color: Black
• Max Pressure: 350 PSI
• End: 3/8” Brass 45° SAE Female Swivel Flare
• End: 3/8” Brass 45° SAE Female Swivel Flare
• TO BE INSTALLED BY LICENSED GAS FITTERS ONLY
• Weight: 0.40 lbs

Fairview QD-GMC6-6F GAS-FLO™ 3/8” Coupler x 3/8” FPT LPG/Nat. Gas Quick Disconnect. Fairview's CSA LPG/Nat. Gas Couplers are CSA Certified up to 60 PSI WP

Features:
• C.S.A. GAS INTERCHANGE QUICK DISCONNECTS (QD-GMC)
• CSA certified to Z21.41/CSA6.9 for Natural Gas and LP-Gas – air mixtures
• All QD-GMC Quick Disconnects Rated To 60 P.S.I.
• QD-GMC Sizes 1/4, 3/8, 1/2 & 3/4 Quick Disconnects Are Rated To A Temperature -40°F

TECHNICAL DATA SHEET

INSTALLATION INSTRUCTIONS

Specifications:
• Coupler (Body Size): 3/8
• Female Pipe Thread: 3/8
• Quick Disconnect BTU Capacity: 85,000
• Material: Brass
• Weight: 3.3 oz

Fairview 725SW-12E 3/4 Hose ID x 3/4 Male Pipe Brass Working Swivel Grip-Tite Fitting. Grip-Tite Push-On style brass hose barbs are recommended for general purpose air, fuel, lube, Oil Lines, water and other low pressure applications. CA360 brass

Specifications:
• Working Pressure: 300 PSI
• Working Temperature: -40°F to +220°F, -40°C to +104°C
• When used with Grip-Tite or similar push-on hose, no clamps are needed
• Weight: 0.24 lbs

Fairview GAS-FLO™ BV2103-E 3/4" FPT Forged Brass Ball Valve 600 WOG, 150 WSP. Fairview's Forged Brass Ball Valves are full port and CSA, CGA & UL certified

TECHNICAL DATA SHEET

INSTALLATION DATA SHEET

Features:
• Brass valves for use in W.O.G. = Water, Oil and Gas; W.S.P. = Working Steam Pressure applications
• Two piece Body
• Full Port
• Blowout-Proof Stem
• PTFE Seats
• CSA - ANSI Z21.15/CGA 9.1, ASME B16.44, CGA CR 91-00
• CAN/CGA 3.16, ASME B16.33 & ASME B16.38
• UL 842 (MHKZ): Manual valves-250 psi

Specifications:
• W.O.G: 600
• W.S.P: 150
• Pipe Size: 3/4” FPT
• Connection Type: Female to Female
• Materials: Brass C3700, Chrome & Nickel Plated Steel, PTFE
• Weight: 0.66 lbs

Fairview PC1469SW-8C 1/2 Tube OD x 3/8 MPT Brass D.O.T. Push-To-Connect 90° Male Swivel Elbow Air Brake Fitting. Fairview's 90° Male Pipe Swivel Elbows Feature A Labor Saving Full Flow Design That Requires No Tools

Applications:
• Air brake systems. Used with copper tubing for rigid plumbing along frame and air tank
• Use with J844D Nylon Air Brake Tube
• D.O.T. RECOGNIZED FOR ALL AIR BRAKE APPLICATIONS EXCEPT THOSE FOR USE BETWEEN FRAME AND AXLE OR BETWEEN TOWED AND TOWING VEHICLES

TECHNICAL DATA SHEET

INSTALLATION DATA SHEET

Specifications:
• Fitting Type: Push-To-Connect
• Fitting Style: 90° Male Swivel Elbow
• Tube OD: 1/2"
• Pipe Thread: 3/8" MPT
• Material: Brass
• Working Temperature: -40°F (-40°C) to 225°F (107°C)
• Weight 0.17 lbs

Accutek® S1001-D Steel Female Tee 1/2 Female Pipe x 1/2 Female Pipe x 1/2 Female Pipe Hydraulic Fitting. Fairview's SAE steel pipe fittings create a stress-generated seal.

Specifications:
• Applications - Water, Oil, Air
• Working Pressure: 3,000 PSI
• Burst Pressure: 12,000 PSI
• Working Temperature: -65°F (-54°C) to 250°F (120°C)
• Pipe threads must be sealed using approved thread sealant
• Weight: 0.44 lbs

Accutek® S1016-E Steel 90° Street Elbow 3/4 Male Pipe x 3/4 Female Pipe Hydraulic Fitting. Fairview's SAE steel pipe fittings create a stress-generated seal.

Specifications:
• Applications - Water, Oil, Air
• Working Pressure: 2,500 PSI
• Burst Pressure: 10,000 PSI
• Working Temperature: -65°F (-54°C) to 250°F (120°C)
• Pipe threads must be sealed using approved thread sealant
• Weight: 0.75 lbs

Fairview PC1469SW-8B 1/2 Tube OD x 1/4 MPT Brass D.O.T. Push-To-Connect 90° Male Swivel Elbow Air Brake Fitting. Fairview's 90° Male Pipe Swivel Elbows Feature A Labor Saving Full Flow Design That Requires No Tools

Applications:
• Air brake systems. Used with copper tubing for rigid plumbing along frame and air tank
• Use with J844D Nylon Air Brake Tube
• D.O.T. RECOGNIZED FOR ALL AIR BRAKE APPLICATIONS EXCEPT THOSE FOR USE BETWEEN FRAME AND AXLE OR BETWEEN TOWED AND TOWING VEHICLES

TECHNICAL DATA SHEET

INSTALLATION DATA SHEET

Specifications:
• Fitting Type: Push-To-Connect
• Fitting Style: 90° Male Swivel Elbow
• Tube OD: 1/2"
• Pipe Thread: 1/4" MPT
• Material: Brass
• Working Temperature: -40°F (-40°C) to 225°F (107°C)
• Weight 0.16 lbs

Accutek® QD-ISOAC6-6F 3/8 Coupler x 3/8 Female Pipe ISO Series A 7241-1 Steel 4,600 PSI Quick Disconnect. Fairview's ISO A Interchange Couplers Interchange with Aeroquip 5600, Parker 6600, Safeway S56 and Faster ANV Series

Features:
• Industry interchangeability with other manufacturer's ISO "A" couplers and nipples
• High Strength Steel Construction
• Nitrile NBR seals with PTFE back-up ring
• Proven ball lock mechanism
• 4 : 1 safety factor (Min. Burst = WP. X 4)
• Hydraulic applications where connection and disconnection is required either for maintenance or operation
• For use on truck & trailer, snow plows, agricultural, dump, construction equipment

Specifications:
• Working Pressure: 4,600 PSI
• Body Size: 3/8
• Female Pipe: 3/8
• Body Material: Steel
• Temperature Range: -40F to 250F
• Approx. Weight: 0.33 lbs

Fairview 44R-106 (1) 5/8 Tube OD x (2) 5/8 Tube OD x (3) 3/8 Tube OD Brass Union Reducing Tee. Fairview's Forged Brass Union Reducing Tee SAE 45° Flare Fittings are ideal for use with LP-Gas, Natural Gas, Refrigeration, Gasoline and more

TECHNICAL DATA SHEET

INSTALLATION DATA SHEET

Specifications:
• Used with Copper, aluminum, and Welded Steel Hydraulic Tube that can be flared
• Working Pressure: 650 PSI
• Material: Forged brass
• Working Temperature: -65°F (-54°C) to 250°F (120°C)
• Weight: 0.30 lbs

Accutek® QD-ISOBC6-6F 3/8 Coupler x 3/8 Female Pipe ISO Series B 7241-1 Steel 4,350 PSI Quick Disconnect. Fairview's ISO B Interchange Couplers Interchange with Aeroquip FD45, Foster FHK, Parker 60, Safeway BS10 and Faster HNV Series

Features:
• High flow characteristics and pressure ratings superior to Parker 60 series
• Industry interchangeability with other manufacturer's ISO "B" couplers and nipples
• Poppet style double shut-off.
• Nitrile NBR seals with PTFE back-up ring
• Proven ball lock mechanism
• 4 : 1 safety factor (Min. Burst = WP. X 4)
• Ideal for use with hydraulic and other fluids in both stationary and mobile industrial applications

Specifications:
• Working Pressure: 4,350 PSI
• Body Size: 3/8
• Female Pipe: 3/8
• Body Material: Steel
• Approx. Weight: 0.48 lbs

Accutek® S1099-ED Steel 90° Elbow 3/4 Male Pipe x 1/2 Male Pipe Hydraulic Fitting. Fairview's SAE steel pipe fittings create a stress-generated seal.

Specifications:
• Applications - Water, Oil, Air
• Working Pressure: 2,500 PSI
• Burst Pressure: 10,000 PSI
• Working Temperature: -65°F (-54°C) to 250°F (120°C)
• Pipe threads must be sealed using approved thread sealant
• Weight: 0.47 lbs

Fairview PC1474SW-8B 1/2 Tube OD x 1/4 MPT Brass D.O.T. Push-To-Connect 45° Male Swivel Elbow Air Brake Fitting. Fairview's 45° Male Pipe Swivel Elbows Feature A Labor Saving Full Flow Design That Requires No Tools

Applications:
• Air brake systems. Used with copper tubing for rigid plumbing along frame and air tank
• Use with J844D Nylon Air Brake Tube
• D.O.T. RECOGNIZED FOR ALL AIR BRAKE APPLICATIONS EXCEPT THOSE FOR USE BETWEEN FRAME AND AXLE OR BETWEEN TOWED AND TOWING VEHICLES

TECHNICAL DATA SHEET

INSTALLATION DATA SHEET

Specifications:
• Fitting Type: Push-To-Connect
• Fitting Style: 45° Male Swivel Elbow
• Tube OD: 1/2"
• Pipe Thread: 1/4" MPT
• Material: Brass
• Working Temperature: -40°F (-40°C) to 225°F (107°C)
• Weight 0.14 lbs

Fairview GAS-FLO™ 850-B Brass Precision LP Gas Needle Valve 1/4 FPT x 1/4 MPT. Fairview's Female To Male Pipe instrumentation valves are CSA certified for use with LP-Gas up to 350 PSI

Applications:
• These instrumentation valves have knurled brass hand wheels
• For use with air, LP gases (such as torch applications) and liquids
• Each valve is pressure tested at the factory
• The valve body's machined from brass bar stock
• The stem is stainless steel with a fine thread for controlling flow
• O-ring packing assures leak proof trouble free service

TECHNICAL DATA SHEET

INSTALLATION DATA SHEET

Specifications:
• C.S.A. CERTIFIED: LP GAS To 350 P.S.I.
• Inlet : 1/4” FPT
• Outlet : 1/4” MPT
• Temperature: -40°F to +180°F (-40°C to +82°C)
• Weight: 4.4 oz

Fairview GAS-FLO™ 853-L Brass Precision LP Gas Welding Standard Needle Valve 1/4 MPT x 9/16-18 LH. Fairview's Welding Standard instrumentation valves are CSA certified for use with LP-Gas up to 350 PSI

Applications:
• These instrumentation valves have knurled brass hand wheels
• For use with air, LP gases (such as torch applications) and liquids
• Each valve is pressure tested at the factory
• The valve body's machined from brass bar stock
• The stem is stainless steel with a fine thread for controlling flow
• O-ring packing assures leak proof trouble free service

TECHNICAL DATA SHEET

INSTALLATION DATA SHEET

Specifications:
• C.S.A. CERTIFIED: LP GAS To 350 P.S.I.
• Inlet : 1/4” MPT
• Outlet : 9/16-18 LH Welding Standard
• Temperature: -40°F to +180°F (-40°C to +82°C)
• Weight: 4.5 oz