General Pump

General Pump 2100203 Swivel Repair Kit (Minor) for Duct Cleaner & Hammerhead Surface Cleaners

Specifications:
• Repair Kit For 2103220, 2103226 & 2103293 Swivels
• Weighs 0.95 lbs

General Pump 2100472 Low Pressure In-line Water Filter 1/2” NTP-F x 1/2” NTP-M with 1/4" Bypass Ports

Features
• Low-pressure in-line filter
• Rigid construction
• Stainless Steel mesh filter
• Die cast aluminum (anodized) housing and plastic cap
• No tools required for cleaning
• Ports for bypass hose and gauge

Specifications
• Max Volume: 8.0 GPM
• Maximum Pressure: 145 PSI
• Temperature: 176° F
• Filter: 50 Mesh
• Inlet: 1/2” NTP-F
• Outlet: 1/2” NPT-M
• Bypass Ports: 1/4” F
• Materials: Aluminum, Brass, Plastic, Buna-N
• Weight: 0.30 Lbs

General Pump PTP™ Series Pressure Washer Thermal Relief Valve with 3/8" Male Inlet. Protects the pump from damaging heat build-up while it is in bypass mode. The thermal relief valve, sensing a rise in temperature, opens and discharges a small amount of heated fluid. This allows cooler water to enter the system and cool the pump. When the gun is discharged the cooler water will cause the valve to close immediately.

Specifications:
• Compact Design - Shorter overall length
• Trip Temperature: 190º F.
• Brass body
• Inlet thread size: 3/8" MPT
• 1/4” Brass hose barb
• Mounts easily in the pump manifold,inlet water supply or bypass loop plumbing
• Weight: 1.5 oz

Specifications:
• Compact Design - Shorter overall length
• Trip Temperature: 190º F.
• Brass body
• Inlet thread size: 1/2" MPT
• 1/4” Brass hose barb
• Mounts easily in the pump manifold,inlet water supply or bypass loop plumbing
• Weight: 1.5 oz

General Pump 100323 5,000 PSI Easy Start Valve 3/8” NPT-M Inlet & 1/4” Hose Barb. Eases system start-up. Especially useful for engine-driven pressure washers

Features:
• Fits any brand pump
• Max working pressure of 5,000 PSI
• Designed and made in the USA
• Long-life construction
• Improved seal design limits leaks

Specifications:
• Maximum Pressure: 5,000 PSI
• Max Volume: 8 GPM
• Maximum Temperature: 195° F
• Inlet: 3/8" NPT-M
• Outlet: 1/4” Hose Barb
• Materials: Brass, Stainless Steel, Thermoplastic
• Weight: 0.25 lbs

General Pump 2560001 Multi-Nozzle Holder (Accepts 1/4" MPT Nozzles)

Features
• This handy tool allows you to very quickly switch between four different nozzles on one spray gun wand.
• It accepts any 1/4" NPT-M thread spray nozzles and turns each one into a quick-connect tip.
• Works great for changing between foam and water, reaching multiple height levels, or altering the intensity of the spray without having to carry around several individual nozzles!
• Note: Nozzles not included.

Specifications

Specifications
• Dimensions: 0.70” H x 3.30” L
• Replaces JROD #6540
• Weight: 0.25 lb

General Pump #1.8mm Adjustable Chemical Injector, High Draw, Chemical Draw Up To 20% with 3/8" NPT-M. This 0 - 20% adjustable flow chemical injector is connected to the downstream side of the pressure pump and is activated when using a low pressure soap nozzle. Choose size based on flow rate of your pressure washer

Features
• Up tp a 20% injection draw rate
• Made in the USA
• A cost effective solution to your chemical application needs

Injector Specifications:
• Size: # 1.8 mm (2.0 to 3.0 GPM)
• Max Operating Pressure: 4,500 PSI
• Max Temperature: 195° F
• Inlet: 3/8” NPT-M
• Outlet: 3/8” NPT-M
• Chemical Port: 1/4” Hose Barb
• Materials: Brass, Stainless Steel, Viton
• Note: If between sizes, choose the smaller injector size
• Weight: 0.30 lbs

General Pump #2.1mm Adjustable Chemical Injector, High Draw, Chemical Draw Up To 20% with 3/8" NPT-M. This 0 - 20% adjustable flow chemical injector is connected to the downstream side of the pressure pump and is activated when using a low pressure soap nozzle. Choose size based on flow rate of your pressure washer

Features
• Up tp a 20% injection draw rate
• Made in the USA
• A cost effective solution to your chemical application needs

Injector Specifications:
• Size: # 2.1 mm (3.0 to 5.0 GPM)
• Max Operating Pressure: 4,500 PSI
• Max Temperature: 195° F
• Inlet: 3/8” NPT-M
• Outlet: 3/8” NPT-M
• Chemical Port: 1/4” Hose Barb
• Materials: Brass, Stainless Steel, Viton
• Note: If between sizes, choose the smaller injector size
• Weight: 0.30 lbs

General Pump 100534 6,000 PSI Safety Relief Valve 3/8” MPT-N. This safety relief valve is a manually adjustable pressure-operated device which, according to its setting releases the excess of water when the pressure inside the pump/system exceeds the adjusted value, thus reducing the pressure. The normal working conditions can be restored by turning off and then restarting the system

Features:
• High pressure safety valve: 2,500 – 6,000 PSI relief pressure
• One model fits all pressures - no springs to change
• Less “whistling” and chatter than competing brands
• Highly accurate over full range of pressures
• Fits any brand of pump
• Designed and made in the USA

Specifications:
• Adjustable Range: 2,500 - 6,000 PSI
• Max Volume: 6 GPM
• Discharge: End
• Max Temperature: 32 - 150° F
• Inlet: 3/8" NPT-M
• Dimensions: 2.6” x .875” Hex
• Weight: 0.325 lbs

General Pump #2.3mm Adjustable Chemical Injector, High Draw, Chemical Draw Up To 20% with 3/8" NPT-M. This 0 - 20% adjustable flow chemical injector is connected to the downstream side of the pressure pump and is activated when using a low pressure soap nozzle. Choose size based on flow rate of your pressure washer

Features
• Up tp a 20% injection draw rate
• Made in the USA
• A cost effective solution to your chemical application needs

Injector Specifications:
• Size: # 2.3 mm (5.0 to 8.0 GPM)
• Max Operating Pressure: 4,500 PSI
• Max Temperature: 195° F
• Inlet: 3/8” NPT-M
• Outlet: 3/8” NPT-M
• Chemical Port: 1/4” Hose Barb
• Materials: Brass, Stainless Steel, Viton
• Note: If between sizes, choose the smaller injector size
• Weight: 0.30 lbs

General Pump 100 Pack of Replacement 1/4" EPDM Quick Disconnect Coupler O-Ringe. EPDM is one of the most versatile and durable rubbers available, providing outstanding heat, weather, and ozone resistancee

Specifications
• Fits all standard 1/4" quick disconnect couplers
• Material: EPDM
• Max. Temperature: 250° F
• Color: Black
• Quantity: 100
• Weight: 1 oz

General Pump 100 Pack of Replacement 3/8" EPDM Quick Disconnect Coupler O-Ringe. EPDM is one of the most versatile and durable rubbers available, providing outstanding heat, weather, and ozone resistancee

Specifications
• Fits all standard 3/8" quick disconnect couplers
• Material: EPDM
• Max. Temperature: 250° F
• Color: Black
• Quantity: 100
• Weight: 1 oz

General 47200274 Pump Rail / Foot 2-5/8", 47, 66 Series, Tall

Turbine, PA UR25 & UR32
PA # 25.1631.22

General Pump New & Improved DuraView Inlet Water Filter 1/2" MPT X 3/4 FGH with 1/4" Bypass Ports. For general purpose pressure wash use

Features
• NEW FEATURE: over-molded easy grip nut!
• Strongest see-through filter on the market
• Loadbearing brass spine
• Integrated garden hose connector
• Flow through design
• Clear plastic cover

Specifications
• Maximum Temperature: 180° F
• Max Volume: 8.0 GPM
• Maximum Operating Pressure: 150 PSI
• Minimum Operating Pressure: 15 PSI
• Materials: Brass, Stainless Steel, Buna-N
• Inlet: Female garden hose (FGH)
• Outlet: 1/2” NPT-M
• Bypass Ports: 1/4” NPT-F Bypass Port
• Dimensions: 1.125” x 3.75”
• Weight: 1.50 Lbs

General Pump DuraView Inlet Water Filter 1/2" MPT X 3/4 FGH. For general purpose pressure wash use

Features
• Strongest see-through filter on the market
• Loadbearing brass spine
• Integrated garden hose connector
• Flow through design
• Clear plastic cover

Specifications
• Maximum Temperature: 180° F
• Max Volume: 8.0 GPM
• Maximum Operating Pressure: 150 PSI
• Minimum Operating Pressure: 15 PSI
• Materials: Brass, Stainless Steel, Buna-N
• Inlet: Female garden hose (FGH)
• Outlet: 1/2” NPT-M
• Bypass Ports: None
• BE # 85.300.054
• Dimensions: 1.125” x 3.75”
• Weight: 1.50 Lbs

General Pump DuraView Inlet Water Filter 3/8" MPT X 3/4 FGH. For general purpose pressure wash use

Features
• Strongest see-through filter on the market
• Loadbearing brass spine
• Integrated garden hose connector
• Flow through design
• Clear plastic cover

Specifications
• Maximum Temperature: 180° F
• Max Volume: 8.0 GPM
• Maximum Operating Pressure: 150 PSI
• Minimum Operating Pressure: 15 PSI
• Materials: Brass, Stainless Steel, Buna-N
• Inlet: Female garden hose (FGH)
• Outlet: 3/8” NPT-M
• Bypass Ports: None
• Dimensions: 1.125” x 3.75”
• Weight: 1.50 Lbs

General Pump New & Improved DuraView Inlet Water Filter 3/8" MPT X 3/4 FGH with 1/4" Bypass Ports. For general purpose pressure wash use

Features
• NEW FEATURE: over-molded easy grip nut!
• Strongest see-through filter on the market
• Loadbearing brass spine
• Integrated garden hose connector
• Flow through design
• Clear plastic cover

Specifications
• Maximum Temperature: 180° F
• Max Volume: 8.0 GPM
• Maximum Operating Pressure: 150 PSI
• Minimum Operating Pressure: 15 PSI
• Materials: Brass, Stainless Steel, Buna-N
• Inlet: Female garden hose (FGH)
• Outlet: 3/8” NPT-M
• Bypass Ports: 1/4” NPT-F Bypass Port
• Dimensions: 1.125” x 3.75”
• Weight: 1.50 Lbs