General Pump

General Pump ZH1520 Trapped Pressure Unloader Valve 2,465 PSI 52.8 GPM 1” NPT-F

Features
• Suitable for Industrial use
• Provisions for Panel Mounting
• Suitable for Industrial use
• Single bypass port
• Extremely reliable
• Easy maintenance

Specifications Sheet

Specifications
• Max Volume: 52.8 GPM
• Min Volume: 5.28 GPM
• Maximum Operating Pressure: 2,465 PSI
• Maximum Temperature: 185° F
• Inlet Port: 1" NPT-F
• Outlet Port: 1" NPT-F
• Bypass Port: 1" NPT-F
• Dimensions: 8.27” x 5.07” x 1.81”
• VRP175, VRP 175
• Weight: 4.4 Lbs

General ET1505E34 2,610 PSI 2.1 GPM Direct Drive Pump flanged to direct couple on electric NEMA 56 C motors

Features:
• “HR” anti-corrosion surface treatment on manifold
• New generation seal package
• Dust protection chamber
• Solid ceramic plungers
• Oversized plunger guide
• Optimized inlet and outlet valves
• Oversized crankcase Hollow shaft, flanged for direct couple to electric motors (NEMA56C)

Specifications:
• Max. Volume: 2.1 GPM
• Max. Discharge Pressure: 2,610 PSI
• Max. Horsepower Requirements: 3.7 EBHP
• Max. Pump Speed: 3,400 RPM
• Max. Fluid Temp.: 165º F
• Oil Capacity: 8.5 oz
• Inlet Port Thread: 1/2"-14 BSP-F
• Discharge Port Thread: 3/8"-19 BSP-F
• Shaft Diameter: 5/8” Hollow
• Dimensions – Nominal: 7.3" x 7.4" x 5.5"
• Weight: 11.0 lb

General ET1506E34 2,610 PSI 2.9 GPM Direct Drive Pump flanged to direct couple on electric NEMA 56 C motors

Features:
• “HR” anti-corrosion surface treatment on manifold
• New generation seal package
• Dust protection chamber
• Solid ceramic plungers
• Oversized plunger guide
• Optimized inlet and outlet valves
• Oversized crankcase Hollow shaft, flanged for direct couple to electric motors (NEMA56C)

Specifications:
• Max. Volume: 2.9 GPM
• Max. Discharge Pressure: 2,610 PSI
• Max. Horsepower Requirements: 5.2 EBHP
• Max. Pump Speed: 3,400 RPM
• Max. Fluid Temp.: 165º F
• Oil Capacity: 8.5 oz
• Inlet Port Thread: 1/2"-14 BSP-F
• Discharge Port Thread: 3/8"-19 BSP-F
• Shaft Diameter: 5/8” Hollow
• Dimensions – Nominal: 7.3" x 7.4" x 5.5"
• Weight: 11.0 lb

General ET1506E34 2,610 PSI 2.9 GPM (Left Handed) Direct Drive Pump flanged to direct couple on electric NEMA 56 C motors

Features:
• “HR” anti-corrosion surface treatment on manifold
• New generation seal package
• Dust protection chamber
• Solid ceramic plungers
• Oversized plunger guide
• Optimized inlet and outlet valves
• Oversized crankcase Hollow shaft, flanged for direct couple to electric motors (NEMA56C)

Specifications:
• Max. Volume: 2.9 GPM
• Max. Discharge Pressure: 2,610 PSI
• Max. Horsepower Requirements: 5.2 EBHP
• Max. Pump Speed: 3,400 RPM
• Max. Fluid Temp.: 165º F
• Oil Capacity: 8.5 oz
• Inlet Port Thread: 1/2"-14 BSP-F
• Discharge Port Thread: 3/8"-19 BSP-F
• Shaft Diameter: 5/8” Hollow
• Dimensions – Nominal: 7.3" x 7.4" x 5.5"
• Weight: 11.0 lb

2,610 PSI 2.9 GPM General PMRET1506G6 Direct Drive Pump Made Ready W/ PULSAR4KHPEZ EZ Start Unloader. Pump is ready to use right out of the box

PUMP:
• General ET1506G6 Pump with SAE J609A Gas Flange
• Direct Drive with Gas Flange 5.0-7.0 HP SAE
• Max. Volume: 2.9 GPM
• Max. Discharge Pressure: 2,610 PSI
• Max. Pump Speed: 3,400 RPM
• Shaft Diameter: 3/4” Hollow
• Max. Horsepower Requirements: 6.9 GHP
• Max. Fluid Temp.: 165º F
• New “HR” anti-corrosion surface treatment on manifold
• Solid ceramic plungers

COMPONENTS:
• General ET1506G6 Triplex Plunger Pump
• PULSAR4KHPEZ EZ Start Unloader 4,050 PSI, 10 GPM
• Thermal relief valve
• 3/8” Hose Barb and Clamp Keeps Hose Secure and Sealed
• 3/4” Garden Hose Inlet Fitting with 1/4” Side Port
• 3/8” QC brass socket and 3/8” QC Plug Included
• Mounting bolts
• Note: Pumps are not tested prior to shipping and unloader will need to be adjusted
• Weight: 14.90 lb

General Pump 2103410 Electric Hose Reel Motor Kit. Fits DHRA Hose Reels

FEATURES
• Allows for effortless rewinding of hose
• Free spin allows for easy pulling out of hose
• Durable powder coated finish
• Stainless steel hardware
• Long lasting hardened gears

SPECIFICATIONS
• Works with DHRA50150, DHRA50300 & DHRA50450 A Frame Hose Reels
• Voltage 12V DC
• Hose Reel Not Included
• Weight 21 lbs

General EZ4040G 4000PSI, 4.0GPM Pump is designed to direct drive on gasoline engines ranging from 9 -13 HP

Features:
• Standard SAE J609 gasoline mounting flange for up to 13 hp engines
• Forged brass manifold with an exclusive lifetime warranty and 3:1 hydrostatic rating
• Die-cast, anodized aluminum oil-bath crankcase
• Innovative one-piece plunger design to eliminate water entering crankcase
• Premium roller bearing
• 5% reduction in crankcase load compared to standard 3,000 PSI, 15 mm pumps
• Unitized stainless steel inlet and discharge valves

Specifications:
• Triplex Plunger Pump
• Direct Drive with Gas Flange 9.0-13.0 HP SAE
• Max. Volume: 4.0 GPM
• Max. Discharge Pressure: 4,000 PSI
• Max. Pump Speed: 3,400 RPM
• Shaft Diameter: 1” Hollow
• Max. Horsepower Requirements: 14.54 GHP
• Max. Fluid Temp.: 165 degrees F.
• Inlet Ports (2): 1/2-14 BSPP-F
• Discharge Ports (2): 3/8-19 BSPP-F
• Drive Side: Standard right
• Note: Item for sale is PUMP ONLY as shown in picture and does not include unloader which is required for proper operation
• Weight: 20.0 lb.

1,500 PSI 2.11 GPM General TT9051EBF Direct Couple to Electric Motors (NEMA 56C)

Features:
• Forged brass manifold with exclusive lifetime warranty
• Die-cast annodized aluminum, oil-bath crankcase
• Solid ceramic plungers with continuously lubricated packings
• The original Interpump unitized, stainless steel, K01 inlet and outlet valves
• Ideal for all general cleaning, RO and misting applications
• Comes standard with NEMA 56C electric motor mounting flange
• Also available in “L” left-handed versions

Specifications Sheet

Specifications:
• Maximum Volume: 2.11 GPM
• Maximum Discharge Pressure: 1,500 PSI
• Maximum Pump Speed: 1,750 RPM
• Maximum Inlet Pressure: 125 PSI
• Oil Capacity: 11.2 oz.
• Maximum Fluid Temperature: 165°F
• Inlet Port Thread: 3/8-19 BSPP-F
• Discharge Port Thread: 1/4-19 BSPP-F
• Shaft Diameter 5/8 in. / 16 mm
• Horespower: 2.2 EBHP
• Weight 12.0 lbs.

1,500 PSI 2.11 GPM General TT9061EBF Direct Couple to Electric Motors (NEMA 56C)

Features:
• Forged brass manifold with exclusive lifetime warranty
• Die-cast annodized aluminum, oil-bath crankcase
• Solid ceramic plungers with continuously lubricated packings
• The original Interpump unitized, stainless steel, K01 inlet and outlet valves
• Ideal for all general cleaning, RO and misting applications
• Comes standard with NEMA 56C electric motor mounting flange
• Also available in “L” left-handed versions

Specifications Sheet

Specifications:
• Maximum Volume: 2.11 GPM
• Maximum Discharge Pressure: 1,500 PSI
• Maximum Pump Speed: 3,400 RPM
• Maximum Inlet Pressure: 125 PSI
• Oil Capacity: 11.2 oz.
• Maximum Fluid Temperature: 165°F
• Inlet Port Thread: 3/8-19 BSPP-F
• Discharge Port Thread: 1/4-19 BSPP-F
• Shaft Diameter 5/8 in. / 16 mm
• Horespower: 2.2 EBHP
• Weight 12.0 lbs.

General Pump 100687 Clutch w/Mounting Plate 47, 66 and 59(ES) Series, 12V, Dual Groove. Mobile Clutch for 24mm Solid Shaft Pump

Features:
• Solid forged rotor. A one-piece solid forged rotor means no chance of internal parts separation. They have an even wall thickness around the coil which gives optimum flux distribution, maximizing torque.
• Different coil voltages available. 12 volt is the most common; 24 volt clutches are also available.
• High temperature, longer-life grease. Our special long-life grease has shown a significant improvement in life over other standard high temp greases.
• E-coating. Where possible, all parts in the clutch are e-coated to give maximum corrosion protection.
• High-temperature epoxy coil. To help prevent failure from vibration and outside contaminants, all coils are sealed in the coil shell with a high-temperature epoxy coating.
• Forged machined pulley. All GP models use a heavy-duty machined pulley. A stronger pulley resists damage

Data Sheet

Specifications:
• Pulley Size & Type: 7" - A Groove, 24mm Shaft
• Width: 2.25"
• Torque After Burnishing: 75 - 95 lbs.
• Power Requirement: 12V 47 Watts
• Weight: 8.0 lbs

General Pump 100688 Clutch w/Mounting Plate 44, 50, 63 and 58 (ES) Series, 12V, Dual Groove. Mobile Clutch for 24mm Solid Shaft Pump

Features:
• Solid forged rotor. A one-piece solid forged rotor means no chance of internal parts separation. They have an even wall thickness around the coil which gives optimum flux distribution, maximizing torque.
• Different coil voltages available. 12 volt is the most common; 24 volt clutches are also available.
• High temperature, longer-life grease. Our special long-life grease has shown a significant improvement in life over other standard high temp greases.
• E-coating. Where possible, all parts in the clutch are e-coated to give maximum corrosion protection.
• High-temperature epoxy coil. To help prevent failure from vibration and outside contaminants, all coils are sealed in the coil shell with a high-temperature epoxy coating.
• Forged machined pulley. All GP models use a heavy-duty machined pulley. A stronger pulley resists damage

Data Sheet

Specifications:
• Pulley Size & Type: 7" - A Groove, 24mm Shaft
• Width: 2.25"
• Torque After Burnishing: 75 - 95 lbs.
• Power Requirement: 12V 47 Watts
• Weight: 8.0 lbs

General Pump 100719 Clutch w/Mounting Plate 47, 66 and 59(ES) Series, 12V, Single Groove. Mobile Clutch for 24mm Solid Shaft Pump

Features:
• Solid forged rotor. A one-piece solid forged rotor means no chance of internal parts separation. They have an even wall thickness around the coil which gives optimum flux distribution, maximizing torque.
• Different coil voltages available. 12 volt is the most common; 24 volt clutches are also available.
• High temperature, longer-life grease. Our special long-life grease has shown a significant improvement in life over other standard high temp greases.
• E-coating. Where possible, all parts in the clutch are e-coated to give maximum corrosion protection.
• High-temperature epoxy coil. To help prevent failure from vibration and outside contaminants, all coils are sealed in the coil shell with a high-temperature epoxy coating.
• Forged machined pulley. All GP models use a heavy-duty machined pulley. A stronger pulley resists damage

Data Sheet

Specifications:
• Pulley Size & Type: 7" - A Groove, 24mm Shaft
• Width: 2.25"
• Torque After Burnishing: 75 - 95 lbs.
• Power Requirement: 12V 47 Watts
• Weight: 8.0 lbs

General Pump 100720 Clutch w/Mounting Plate 44, 50, 63 and 58 (ES) Series, 12V, Single Groove. Mobile Clutch for 24mm Solid Shaft Pump

Features:
• Solid forged rotor. A one-piece solid forged rotor means no chance of internal parts separation. They have an even wall thickness around the coil which gives optimum flux distribution, maximizing torque.
• Different coil voltages available. 12 volt is the most common; 24 volt clutches are also available.
• High temperature, longer-life grease. Our special long-life grease has shown a significant improvement in life over other standard high temp greases.
• E-coating. Where possible, all parts in the clutch are e-coated to give maximum corrosion protection.
• High-temperature epoxy coil. To help prevent failure from vibration and outside contaminants, all coils are sealed in the coil shell with a high-temperature epoxy coating.
• Forged machined pulley. All GP models use a heavy-duty machined pulley. A stronger pulley resists damage

Data Sheet

Specifications:
• Pulley Size & Type: 7" - A Groove, 24mm Shaft
• Width: 2.25"
• Torque After Burnishing: 75 - 95 lbs.
• Power Requirement: 12V 47 Watts
• Weight: 8.0 lbs

General Pump 100719 Clutch w/Mounting Plate 47, 66 and 59(ES) Series, 24V, Dual Groove. Mobile Clutch for 24mm Solid Shaft Pump

Features:
• Solid forged rotor. A one-piece solid forged rotor means no chance of internal parts separation. They have an even wall thickness around the coil which gives optimum flux distribution, maximizing torque.
• Different coil voltages available. 12 volt is the most common; 24 volt clutches are also available.
• High temperature, longer-life grease. Our special long-life grease has shown a significant improvement in life over other standard high temp greases.
• E-coating. Where possible, all parts in the clutch are e-coated to give maximum corrosion protection.
• High-temperature epoxy coil. To help prevent failure from vibration and outside contaminants, all coils are sealed in the coil shell with a high-temperature epoxy coating.
• Forged machined pulley. All GP models use a heavy-duty machined pulley. A stronger pulley resists damage

Data Sheet

Specifications:
• Pulley Size & Type: 7" - A Groove, 24mm Shaft
• Width: 2.25"
• Torque After Burnishing: 75 - 95 lbs.
• Power Requirement: 24V 45.6 Watts
• Weight: 8.0 lbs

General Pump 100720 Clutch w/Mounting Plate 44, 50, 63 and 58 (ES) Series, 24V, Dual Groove. Mobile Clutch for 24mm Solid Shaft Pump

Features:
• Solid forged rotor. A one-piece solid forged rotor means no chance of internal parts separation. They have an even wall thickness around the coil which gives optimum flux distribution, maximizing torque.
• Different coil voltages available. 12 volt is the most common; 24 volt clutches are also available.
• High temperature, longer-life grease. Our special long-life grease has shown a significant improvement in life over other standard high temp greases.
• E-coating. Where possible, all parts in the clutch are e-coated to give maximum corrosion protection.
• High-temperature epoxy coil. To help prevent failure from vibration and outside contaminants, all coils are sealed in the coil shell with a high-temperature epoxy coating.
• Forged machined pulley. All GP models use a heavy-duty machined pulley. A stronger pulley resists damage

Data Sheet

Specifications:
• Pulley Size & Type: 7" - A Groove, 24mm Shaft
• Width: 2.25"
• Torque After Burnishing: 75 - 95 lbs.
• Power Requirement: 24V 45.6 Watts
• Weight: 8.0 lbs

General Pump DCFSCP18GZ 18" Hammerhead Professional Flat Surface Cleaner. The gun has a revolutionary compensating design to reduce fatigue. The cleaner glides easily across the surface uniformly cleaning pool decks, sidewalks, garage floors and more

FEATURES
• Compensating gun feature
• Full 18” cleaning path
• Heavy-duty anodized aluminum components
• Rugged ABS cover
• Swivel has grease zerk fitting for bearing lubrication
• Two Stainless Steel bearings for better performance
• Stainless Steel inlet filter for water filtration
• Supplied with 2-nozzle rotating arm
• Note: Caster Kit Not Included (Optional Caster Kit: P/N 2100200 available)

SPECIFICATIONS
• Max Flow: 8 GPM
• Operating Pressure: 1,000 – 4,000 PSI
• Max. Temp.: 180° F
• Nozzles: 925020M (2)
• Trigger Gun Inlet: 3/8" NPT-F
• Dimensions-Retracted 70”x18.3”x18.3”
• Shipping Weight 19 lbs

General Pump YGR1000P Gear Reducer for 2.2 to 1, 1″ Shafted Engines, Up to 24 HP, J609A Flange, 47, 47SS and 66 Series pumps

Features:
• Compact and lightweight
• Hardened steel helical gears for quiet operation
• Oil bath lubrication
• Dual bearing design for extended life
• J609a Flange mounts to most gasoline engines

Specifications:
• Horse Power: 18 - 24
• Drive Ratio: 2.176:1
• Maximum Pump Speed: 1,450 RPM
• Oil Capacity: 10 Oz
• Oil Grade: SAE90 Gear Lube
• Input (motor) Shaft Ø": 1”
• Output (pump) Shaft Ø": 24 mm
• Motor Flange (SAE): J609A
• Pump Flange: Fits 47, 47SS and 66 Series General Pump
• Weight: 5.8 lb.