General Pump

1,500 PSI 2.11 GPM General TT9061EBFUI Direct Couple to Electric Motors (NEMA 56C) with Built In Unloader and Downstrean injector

Features:
• Forged brass manifold with exclusive lifetime warranty
• Die-cast annodized aluminum, oil-bath crankcase
• Solid ceramic plungers with continuously lubricated packings
• The original Interpump unitized, stainless steel, K01 inlet and outlet valves
• Ideal for all general cleaning, RO and misting applications
• Comes standard with NEMA 56C electric motor mounting flange
• Also available in “L” left-handed versions

Specifications Sheet

Specifications:
• Maximum Volume: 2.11 GPM
• Maximum Discharge Pressure: 1,500 PSI
• Maximum Pump Speed: 3,400 RPM
• Maximum Inlet Pressure: 125 PSI
• Oil Capacity: 11.2 oz.
• Maximum Fluid Temperature: 165°F
• Inlet Port Thread: 3/8-19 BSPP-F
• Discharge Port Thread: 1/4-19 BSPP-F
• Shaft Diameter 5/8 in. / 16 mm
• Horespower: 2.2 EBHP
• Weight 12.0 lbs.

General EP1813S17 Triplex EP Series 1,750 RPM Solid Shaft Plunger Pump.

Features:
• Triplex plunger pump
• New Forged brass manifold
• New plunger guide bushing (patent pending)
• Solid ceramic plungers with dual guide system
• New dual diameter plunger guide
• New optimized outlet valves
• New dual lip oil seal

Specifications Sheet

WARNING: High Pressure Systems require a primary pressure regulating device (i.e. regulator, unloader) and a secondary pressure relief device (i.e. pop-off valve, relief valve). Failure to install such relief devices properly could result in personal injury or damage to pump or property. GP and PRI Industries do not assume any liability or responsibility for the operation of the user’s high pressure system.

Specifications:
• Solid Shaft for Belt or Gear Drive
• Max. Volume: 4.2 GPM
• Max. Discharge Pressure: 2,900 PSI
• Horsepower: 8.3 HP
• Max. Pump Speed: 1,750 RPM
• Maximum Inlet Pressure: 125 PSI
• Oil Capacity: 15 oz
• Max. Fluid Temp.: 165 degrees F.
• Inlet Port Thread: 1/2”-14 BSP-F
• Discharge Port Thread: 3/8”-19 BSP-F
• Shaft Diameter: .945 in./24 mm
• Dimensions – Nominal: 9.5” x 8.38” x 5.1”
• Replaces TX1813S17
• Note: Item for sale is PUMP ONLY as shown in picture and does not include unloader which is required for proper operation
• Weight: 15.4 lb.

General EP1513S17 Triplex EP Series 1,750 RPM Solid Shaft Plunger Pump.

Features:
• Triplex plunger pump
• New Forged brass manifold
• New plunger guide bushing (patent pending)
• Solid ceramic plungers with dual guide system
• New dual diameter plunger guide
• New optimized outlet valves
• New dual lip oil seal

Specifications Sheet

WARNING: High Pressure Systems require a primary pressure regulating device (i.e. regulator, unloader) and a secondary pressure relief device (i.e. pop-off valve, relief valve). Failure to install such relief devices properly could result in personal injury or damage to pump or property. GP and PRI Industries do not assume any liability or responsibility for the operation of the user’s high pressure system.

Specifications:
• Solid Shaft for Belt or Gear Drive
• Max. Volume: 3.2 GPM
• Max. Discharge Pressure: 3,045 PSI
• Horsepower: 6.5 EBHP
• Max. Pump Speed: 1,750 RPM
• Maximum Inlet Pressure: 125 PSI
• Oil Capacity: 15 oz
• Max. Fluid Temp.: 165 degrees F.
• Inlet Port Thread: 1/2”-14 BSP-F
• Discharge Port Thread: 3/8”-19 BSP-F
• Shaft Diameter: .945 in./24 mm
• Dimensions – Nominal: 9.5” x 8.38” x 5.1”
• Replaces TX1513S17
• Note: Item for sale is PUMP ONLY as shown in picture and does not include unloader which is required for proper operation
• Weight: 15.4 lb.

General EP1512S17 Triplex EP Series 1,750 RPM Solid Shaft Plunger Pump.

Features:
• Triplex plunger pump
• New Forged brass manifold
• New plunger guide bushing (patent pending)
• Solid ceramic plungers with dual guide system
• New dual diameter plunger guide
• New optimized outlet valves
• New dual lip oil seal

Specifications Sheet

WARNING: High Pressure Systems require a primary pressure regulating device (i.e. regulator, unloader) and a secondary pressure relief device (i.e. pop-off valve, relief valve). Failure to install such relief devices properly could result in personal injury or damage to pump or property. GP and PRI Industries do not assume any liability or responsibility for the operation of the user’s high pressure system.

Specifications:
• Solid Shaft for Belt or Gear Drive
• Max. Volume: 2.9 GPM
• Max. Discharge Pressure: 3,045 PSI
• Horsepower: 6.0 EBHP
• Max. Pump Speed: 1,750 RPM
• Maximum Inlet Pressure: 125 PSI
• Oil Capacity: 15 oz
• Max. Fluid Temp.: 165 degrees F.
• Inlet Port Thread: 1/2”-14 BSP-F
• Discharge Port Thread: 3/8”-19 BSP-F
• Shaft Diameter: .945 in./24 mm
• Dimensions – Nominal: 9.5” x 8.38” x 5.1”
• Note: Item for sale is PUMP ONLY as shown in picture and does not include unloader which is required for proper operation
• Weight: 15.4 lb.

2,610 PSI 3.2 GPM General PMRET1507G6 Direct Drive Pump Made Ready W/ PULSAR4KHPEZ EZ Start Unloader. Pump is ready to use right out of the box

PUMP:
• General ET1507G6 Pump with SAE J609A Gas Flange
• Direct Drive with Gas Flange 5.0-7.0 HP SAE
• Max. Volume: 3.2 GPM
• Max. Discharge Pressure: 2,610 PSI
• Max. Pump Speed: 3,400 RPM
• Shaft Diameter: 3/4” Hollow
• Max. Horsepower Requirements: 7.6 GHP
• Max. Fluid Temp.: 165º F
• Nickel-plated cast manifold manufactured like heavy-duty pump line
• Solid ceramic plungers

COMPONENTS:
• General ET1507G6 Triplex Plunger Pump
• PULSAR4KHPEZ EZ Start Unloader 4,050 PSI, 10 GPM
• Thermal relief valve
• 3/8” Hose Barb and Clamp Keeps Hose Secure and Sealed
• 3/4” Garden Hose Inlet Fitting with 1/4” Side Port
• 3/8” QC brass socket Installed and 3/8” QC Plug Included
• Mounting bolts
• Note: Pumps are not tested prior to shipping and unloader will need to be adjusted
• Weight: 14.90 lb

• Triplex Plunger Pump
• Direct Drive with Electric Flange NEMA 56C
• Max. Volume: 2.11 GPM
• Max. Discharge Pressure: 1,500 PSI
• Max. Pump Speed: 3400 RPM
• Shaft Diameter: 5/8” Hollow
• Max. Horsepower Requirements: 2.2 BHP
• Max. Fluid Temp.: 165º degrees F.
• Inlet Ports (2): 3/8" BSP
• Discharge Ports (2): 1/4" BSP
• Drive Side: Standard left
• Forged brass head & valve covers
• Solid ceramic plungers
• Weight: 11.5 lb.

• Triplex Plunger Pump
• Direct Drive with Electric Flange NEMA 56C
• Max. Volume: 2.10 GPM
• Max. Discharge Pressure: 2,000 PSI
• Max. Pump Speed: 3400 RPM
• Shaft Diameter: 5/8” Hollow
• Max. Horsepower Requirements: 3.0 BHP
• Max. Fluid Temp.: 165º degrees F.
• Inlet Ports (2): 3/8" BSP
• Discharge Ports (2): 1/4" BSP
• Drive Side: Standard right
• Forged brass head & valve covers
• Solid ceramic plungers
• Weight: 11.5 lb.

• Triplex Plunger Pump
• Direct Drive with Gas Flange 3.0-6.5 HP SAE
• Max. Volume: 2.80 GPM
• Max. Discharge Pressure: 2,000 PSI
• Max. Pump Speed: 3400 RPM
• Shaft Diameter: 3/4” Hollow
• Max. Horsepower Requirements: 5.0 GHP
• Max. Fluid Temp.: 165 degrees F.
• Inlet Ports (2): 3/8" BSP
• Discharge Ports (2): 1/4" BSP
• Drive Side: Standard right
• Forged brass head
• Solid ceramic plungers
• Weight: 11.4 lb.

• Triplex Plunger Pump
• Direct Drive with Electric Flange NEMA 56C
• Max. Volume: 2.80 GPM
• Max. Discharge Pressure: 2,000 PSI
• Max. Pump Speed: 3400 RPM
• Shaft Diameter: 5/8” Hollow
• Max. Horsepower Requirements: 4.0 BHP
• Max. Fluid Temp.: 165º degrees F.
• Inlet Ports (2): 3/8" BSP
• Discharge Ports (2): 1/4" BSP
• Drive Side: Standard right
• Forged brass head & valve covers
• Solid ceramic plungers
• Weight: 11.5 lb.

• Triplex Plunger Pump
• Direct Drive with Gas Flange 3.0-6.5 HP SAE
• Max. Volume: 3.50 GPM
• Max. Discharge Pressure: 2,000 PSI
• Max. Pump Speed: 3400 RPM
• Shaft Diameter: 3/4” Hollow
• Max. Horsepower Requirements: 6.5 GHP
• Max. Fluid Temp.: 165 degrees F.
• Inlet Ports (2): 3/8" BSP
• Discharge Ports (2): 1/4" BSP
• Drive Side: Standard right
• Forged brass head
• Solid ceramic plungers
• Weight: 11.4 lb.

• Triplex Plunger Pump
• Direct Drive with Electric Flange NEMA 56C
• Max. Volume: 3.50 GPM
• Max. Discharge Pressure: 2,000 PSI
• Max. Pump Speed: 3400 RPM
• Shaft Diameter: 5/8” Hollow
• Max. Horsepower Requirements: 5.0 BHP
• Max. Fluid Temp.: 165º degrees F.
• Inlet Ports (2): 3/8" BSP
• Discharge Ports (2): 1/4" BSP
• Drive Side: Standard right
• Forged brass head & valve covers
• Solid ceramic plungers
• Weight: 11.5 lb.

• Triplex Plunger Pump
• Solid Shaft for Belt or Gear Drive
• Max. Volume: 2.11 GPM
• Max. Discharge Pressure: 1,500 PSI
• Max. Pump Speed: 2800 RPM
• Shaft Diameter: 24mm Solid
• Max. Horsepower Requirements: 2.0 BHP
• Max. Fluid Temp.: 165 degrees F.
• Inlet Ports (2): 3/8" BSP
• Discharge Ports (2): 1/4" BSP
• Drive Side: Standard right
• Forged brass head & valve covers
• Solid ceramic plungers
• Weight: 11.2 lb.

• Triplex Plunger Pump
• Direct Drive with Electric Flange NEMA 56C
• Max. Volume: 2.80 GPM
• Max. Discharge Pressure: 1,500 PSI
• Max. Pump Speed: 3400 RPM
• Shaft Diameter: 5/8” Hollow
• Max. Horsepower Requirements: 3.0 BHP
• Max. Fluid Temp.: 165º degrees F.
• Inlet Ports (2): 3/8" BSP
• Discharge Ports (2): 1/4" BSP
• Drive Side: Standard right
• Forged brass head & valve covers
• Solid ceramic plungers
• Weight: 11.5 lb.

• Triplex Plunger Pump
• Direct Drive with Gas Flange 3.0-6.5 HP SAE
• Max. Volume: 2.80 GPM
• Max. Discharge Pressure: 1,500 PSI
• Max. Pump Speed: 3400 RPM
• Shaft Diameter: 3/4” Hollow
• Max. Horsepower Requirements: 4.0 GHP
• Max. Fluid Temp.: 165 degrees F.
• Inlet Ports (2): 3/8" BSP
• Discharge Ports (2): 1/4" BSP
• Drive Side: Standard right
• Forged brass head
• Solid ceramic plungers
• Weight: 11.4 lb.

• Triplex Plunger Pump
• Solid Shaft for Belt or Gear Drive
• Max. Volume: 3.0 GPM
• Max. Discharge Pressure: 1,500 PSI
• Max. Pump Speed: 1750 RPM
• Shaft Diameter: 24mm Solid
• Max. Horsepower Requirements: 3.0 BHP
• Max. Fluid Temp.: 165 degrees F.
• Inlet Ports (2): 3/8" BSP
• Discharge Ports (2): 1/4" BSP
• Drive Side: Standard right
• Forged brass head & valve covers
• Solid ceramic plungers
• Weight: 11.2 lb.

General Pump YGR1000P Gear Reducer for 2.2 to 1, 1″ Shafted Engines, Up to 24 HP, J609A Flange, 47, 47SS and 66 Series pumps

Features:
• Compact and lightweight
• Hardened steel helical gears for quiet operation
• Oil bath lubrication
• Dual bearing design for extended life
• J609a Flange mounts to most gasoline engines

Specifications:
• Horse Power: 18 - 24
• Drive Ratio: 2.176:1
• Maximum Pump Speed: 1,450 RPM
• Oil Capacity: 10 Oz
• Oil Grade: SAE90 Gear Lube
• Input (motor) Shaft Ø": 1”
• Output (pump) Shaft Ø": 24 mm
• Motor Flange (SAE): J609A
• Pump Flange: Fits 47, 47SS and 66 Series General Pump
• Weight: 5.8 lb.

General Pump DCFSCP18GZ 18" Hammerhead Professional Flat Surface Cleaner. The gun has a revolutionary compensating design to reduce fatigue. The cleaner glides easily across the surface uniformly cleaning pool decks, sidewalks, garage floors and more

FEATURES
• Compensating gun feature
• Full 18” cleaning path
• Heavy-duty anodized aluminum components
• Rugged ABS cover
• Swivel has grease zerk fitting for bearing lubrication
• Two Stainless Steel bearings for better performance
• Stainless Steel inlet filter for water filtration
• Supplied with 2-nozzle rotating arm
• Note: Caster Kit Not Included (Optional Caster Kit: P/N 2100200 available)

SPECIFICATIONS
• Max Flow: 8 GPM
• Operating Pressure: 1,000 – 4,000 PSI
• Max. Temp.: 180° F
• Nozzles: 925020M (2)
• Trigger Gun Inlet: 3/8" NPT-F
• Dimensions-Retracted 70”x18.3”x18.3”
• Shipping Weight 19 lbs

General Pump 100687 Clutch w/Mounting Plate 47, 66 and 59(ES) Series, 12V, Dual Groove. Mobile Clutch for 24mm Solid Shaft Pump

Features:
• Solid forged rotor. A one-piece solid forged rotor means no chance of internal parts separation. They have an even wall thickness around the coil which gives optimum flux distribution, maximizing torque.
• Different coil voltages available. 12 volt is the most common; 24 volt clutches are also available.
• High temperature, longer-life grease. Our special long-life grease has shown a significant improvement in life over other standard high temp greases.
• E-coating. Where possible, all parts in the clutch are e-coated to give maximum corrosion protection.
• High-temperature epoxy coil. To help prevent failure from vibration and outside contaminants, all coils are sealed in the coil shell with a high-temperature epoxy coating.
• Forged machined pulley. All GP models use a heavy-duty machined pulley. A stronger pulley resists damage

Data Sheet

Specifications:
• Pulley Size & Type: 7" - A Groove, 24mm Shaft
• Width: 2.25"
• Torque After Burnishing: 75 - 95 lbs.
• Power Requirement: 12V 47 Watts
• Weight: 8.0 lbs

General Pump 100688 Clutch w/Mounting Plate 44, 50, 63 and 58 (ES) Series, 12V, Dual Groove. Mobile Clutch for 24mm Solid Shaft Pump

Features:
• Solid forged rotor. A one-piece solid forged rotor means no chance of internal parts separation. They have an even wall thickness around the coil which gives optimum flux distribution, maximizing torque.
• Different coil voltages available. 12 volt is the most common; 24 volt clutches are also available.
• High temperature, longer-life grease. Our special long-life grease has shown a significant improvement in life over other standard high temp greases.
• E-coating. Where possible, all parts in the clutch are e-coated to give maximum corrosion protection.
• High-temperature epoxy coil. To help prevent failure from vibration and outside contaminants, all coils are sealed in the coil shell with a high-temperature epoxy coating.
• Forged machined pulley. All GP models use a heavy-duty machined pulley. A stronger pulley resists damage

Data Sheet

Specifications:
• Pulley Size & Type: 7" - A Groove, 24mm Shaft
• Width: 2.25"
• Torque After Burnishing: 75 - 95 lbs.
• Power Requirement: 12V 47 Watts
• Weight: 8.0 lbs

General Pump 100719 Clutch w/Mounting Plate 47, 66 and 59(ES) Series, 12V, Single Groove. Mobile Clutch for 24mm Solid Shaft Pump

Features:
• Solid forged rotor. A one-piece solid forged rotor means no chance of internal parts separation. They have an even wall thickness around the coil which gives optimum flux distribution, maximizing torque.
• Different coil voltages available. 12 volt is the most common; 24 volt clutches are also available.
• High temperature, longer-life grease. Our special long-life grease has shown a significant improvement in life over other standard high temp greases.
• E-coating. Where possible, all parts in the clutch are e-coated to give maximum corrosion protection.
• High-temperature epoxy coil. To help prevent failure from vibration and outside contaminants, all coils are sealed in the coil shell with a high-temperature epoxy coating.
• Forged machined pulley. All GP models use a heavy-duty machined pulley. A stronger pulley resists damage

Data Sheet

Specifications:
• Pulley Size & Type: 7" - A Groove, 24mm Shaft
• Width: 2.25"
• Torque After Burnishing: 75 - 95 lbs.
• Power Requirement: 12V 47 Watts
• Weight: 8.0 lbs