General Pump

General Pump New & Improved DuraView Inlet Water Filter 1/2" MPT X 3/4 FGH with 1/4" Bypass Ports. For general purpose pressure wash use

Features
• NEW FEATURE: over-molded easy grip nut!
• Strongest see-through filter on the market
• Loadbearing brass spine
• Integrated garden hose connector
• Flow through design
• Clear plastic cover

Specifications
• Maximum Temperature: 180° F
• Max Volume: 8.0 GPM
• Maximum Operating Pressure: 150 PSI
• Minimum Operating Pressure: 15 PSI
• Materials: Brass, Stainless Steel, Buna-N
• Inlet: Female garden hose (FGH)
• Outlet: 1/2” NPT-M
• Bypass Ports: 1/4” NPT-F Bypass Port
• Dimensions: 1.125” x 3.75”
• Weight: 1.50 Lbs

General Pump DuraView Inlet Water Filter 1/2" MPT X 3/4 FGH. For general purpose pressure wash use

Features
• Strongest see-through filter on the market
• Loadbearing brass spine
• Integrated garden hose connector
• Flow through design
• Clear plastic cover

Specifications
• Maximum Temperature: 180° F
• Max Volume: 8.0 GPM
• Maximum Operating Pressure: 150 PSI
• Minimum Operating Pressure: 15 PSI
• Materials: Brass, Stainless Steel, Buna-N
• Inlet: Female garden hose (FGH)
• Outlet: 1/2” NPT-M
• Bypass Ports: None
• BE # 85.300.054
• Dimensions: 1.125” x 3.75”
• Weight: 1.50 Lbs

General YVB9KMS2 Trapped Pressure Unloader w/ Microswitch 3,650 PSI 8.0 GPM

Features:
• Extremely durable construction in stainless steel and brass
• Easy start-up due to low re-arm pressure (27% of operating pressure)
• Hexagonal discharge check valve to prevent binding
• Unloader with microswitch
• Waterproof, 5-amp pressure switch, UL Listed

Specifications:
• Rated Pressure: 3,200 PSI
• Maximum Pressure: 3,650 PSI
• Rated Temperature: 195° F
• Maximum Flow: 8.0 GPM
• Pressure Switch: 1 amp ind., 5 amps res, 250 Volts
• Inlet Port: 3/8” BSP-F
• Outlet Port: 3/8” BSP-F
• Bypass Port: 3/8” BSP-F
• Gauge Port: 1/4” F
• Weight: 1.6 lbs

PA RL 57 / GP YG7207 Easy Pull Spray Gun 8,000 PSI 7.5 GPM. No fluid passage upon trigger release. New mechanical device with double connecting rods to guarantee less strain when opening and holding

Features
• Covered by shockproof plastic semi-housings
• Seat in Sst and ball in Widia
• Totally built in stainless steel AISI 303
• Ergonomic construction
• Minimum fatigue for trigger opening and use
• New mechanical opening device with double connecting rods
• New trigger design, rotating on a fixed pin to guarantee better mobility and steadiness

Specifications
• Rated Pressure: 7,250 PSI
• Permissible Pressure: 8,000 PSI
• Max Flow: 7.5 GPM
• Max Temp: 320° F.
• Inlet: 3/8" NPT-F
• Outlet: 1/4" NPT-F
• Use # 2100378 matching 36” lance
• Replaces 30.4700.00
• Weight: 25.18 oz

General Pump Packing Extraction Tool Kit. Tools for removing packings from pumps 13mm through 24mm

Kit Includes:
• Plastic carrying case
• Slide hammer
• Sockets: 13mm, 15mm, 18mm, 20mm, 22mm & 24mm
• Weight: 7.0 lbs

General DCG5010HE Compensating Spray Gun for Hydro Excavation.

Features:
• Specifically designed for use in hydro excavation!
• Exclusive patented GP design
• Unique design compensates for changes in pressure
• Trigger designed for low fatigue
• Allows for continued use without tiring hand
• All flow passages designed for minimum pressure drop - maximum flow
• Fluorocarbon seals for maximum high temperature performance
• Large comfortable hand grip to accommodate work gloves
• Additional venting for excellent high temperature performance
• Durable glass-filled housing and trigger in Zytel (high tech nylon)

Specifications:
• Max Pressure: 5,000 PSI
• Max Flow: 10.5 GPM
• Max Temp: 320° F.
• Inlet: 3/8" Female NPT
• Outlet: 1/4" Female NPT
• Weight: 1.4 lbs

General Pump 1/2” MPT x 48” 304L Stainless Steel 4,500 PSI Hydro Excavating Lance

Specifications:
• Length: 48"
• Pipe Material: 304L Stainless steel
• Inlet: 1/2” Male NPT
• Outlet: 1/2” Male NPT
• Maximum Pressure: 4,500 PSI
• Weight: 4.0 Lbs

General Pump 1/2” MPT x 60” 304L Stainless Steel 4,500 PSI Hydro Excavating Lance

Specifications:
• Length: 60"
• Pipe Material: 304L Stainless steel
• Inlet: 1/2” Male NPT
• Outlet: 1/2” Male NPT
• Maximum Pressure: 4,500 PSI
• Weight: 5.0 Lbs

General YG4032S / PA 30.0680.50 High Flow 32 GPM Straight, Rear Entry Spray Gun for Hydro Excavation.

Features:
• Shockproof plastic housing
• Unique design compensates for changes in pressure
• Internal construction of brass and Stainless Steel
• Ergonomic design
• Minimizes fatigue for the operator

Specifications:
• Max Volume: 32 GPM
• Rated Discharge Pressure: 4,050 PSI
• Max Discharge Pressure: 4,500 PSI
• Max Temp: 210° F.
• Inlet: 1/2" Female NPT
• Outlet: 1/2" Female NPT
• Materials: Stainless Steel, Brass, Plastic, Viton
• Weight: 2.8 lbs

General / PA YG4500S Linear Rear Entry Trigger Gun.

Features:
• Shockproof plastic housing
• Ergonomic design, Minimizes fatigue for the operator
• Stainless Steel seat and ball
• Internal construction of brass and Stainless Steel

Specifications:
• Max Pressure: 5,000 PSI
• Max Flow: 10.5 GPM
• Max Temp: 320° F.
• Inlet: 3/8" Female NPT
• Outlet: 1/4" Female NPT
• Weight: 1.2 lbs

General TSS1511 Triplex Plunger Pump. The preferred pump frame in the pressure cleaning industry

Features:
• Forged brass manifold with an exclusive lifetime warranty
• Large-capacity, die-cast, anodized aluminum oil-bath crankcase
• Over-sized connecting rods for maximum life
• Solid ceramic plungers with continuously lubricated packings
• Unitized stainless steel inlet and discharge valves
• Designed for suction applications
• Manifold with fine thread valve caps

Specifications Sheet

WARNING: High Pressure Systems require a primary pressure regulating device (i.e. regulator, unloader) and a secondary pressure relief device (i.e. pop-off valve, relief valve). Failure to install such relief devices properly could result in personal injury or damage to pump or property. GP and PRI Industries do not assume any liability or responsibility for the operation of the user’s high pressure system.

Specifications:
• Triplex Plunger Pump
• Solid Shaft for Belt or Gear Drive
• Max. Volume: 4.0 GPM
• Max. Discharge Pressure: 3,500 PSI
• Max. Pump Speed: 1450 RPM
• Shaft Diameter: 24mm Solid
• Max. Horsepower Requirements: 13.0 GHP
• Max. Fluid Temp.: 165 degrees F.
• Inlet Ports (2): 1/2" BSP
• Discharge Ports (2): 3/8" BSP
• Drive Side: Standard right
• Forged brass head & valve covers
• Solid ceramic plungers
• Replaces TS1511 & TS1011
• Note: Item for sale is PUMP ONLY as shown in picture and does not include unloader which is required for proper operation
• Weight: 32.0 lb.

PA LS 12 / General Pump YLS12T Replacement 1 L Bottle
Only works with model 25.1840.15, 25.1840.65 & YLS12T
PA # 14.6506.00

Specifications:
• Spring Color: Green
• Maximum Pressure: 4,500 PSI
• Rated Pressure: 4,050 PSI
• Max. Volume: 21.0 GPM
• Adjustable pressure
• Forged brass body
• Maximum Temperature: 200° F
• Inlet Ports (2): 1/2" FPT
• Discharge Port: 1/2” FPT
• Bypass Ports (2): 1/2” FPT
• Weight: 3.1 lb

Repair Kit, YG2953, RL19, RL204
PA # 30.4046.24

General Pump 40° (White) #2.5 Quick Connect (Q) Spray Nozzle

Features
• 5,000 PSI operating pressure
• Made in the USA
• Ceramic insert is resistant to wear
• Through-hardened stainless steel orifices offer superior wear resistance compared to standard case hardened nozzles
• Stainless steel housing resists cracking and wear
• Resistant to most chemical
• Large color coded tip protector on Q-type nozzles permits rapid identification of fan angle
• Laser marked for clarity and durability

Specifications
• Tip Angle: 40° (White)
• Nozzle Size: 2.5
• Operating Pressure: 5,000 PSI
• Connection: 1/4” QC Plug
• Weight: 0.05 oz

Please use Nozzle Chart to determine proper nozzle size

Nozzle Chart

General Pump 25° (Green) #2.5 Quick Connect (Q) Spray Nozzle

Features
• 5,000 PSI operating pressure
• Made in the USA
• Ceramic insert is resistant to wear
• Through-hardened stainless steel orifices offer superior wear resistance compared to standard case hardened nozzles
• Stainless steel housing resists cracking and wear
• Resistant to most chemical
• Large color coded tip protector on Q-type nozzles permits rapid identification of fan angle
• Laser marked for clarity and durability

Specifications
• Tip Angle: 25° (Green)
• Nozzle Size: 2.5
• Operating Pressure: 5,000 PSI
• Connection: 1/4” QC Plug
• Weight: 0.05 oz

Please use Nozzle Chart to determine proper nozzle size

Nozzle Chart

General Pump 15° (Yellow) #2.5 Quick Connect (Q) Spray Nozzle

Features
• 5,000 PSI operating pressure
• Made in the USA
• Ceramic insert is resistant to wear
• Through-hardened stainless steel orifices offer superior wear resistance compared to standard case hardened nozzles
• Stainless steel housing resists cracking and wear
• Resistant to most chemical
• Large color coded tip protector on Q-type nozzles permits rapid identification of fan angle
• Laser marked for clarity and durability

Specifications
• Tip Angle: 15° (Yellow)
• Nozzle Size: 2.5
• Operating Pressure: 5,000 PSI
• Connection: 1/4” QC Plug
• Weight: 0.05 oz

Please use Nozzle Chart to determine proper nozzle size

Nozzle Chart