P.A. Srl

PA Pulsar 4 Unloader Plumbing Kit for Pressure Washer Pump with EZ Start– 4,050 PSI Max. This unloader kit has all the components to make installation easy

Specifications:
• Works with pumps that have 1/2” FPT inlet and 3/8” FPT Outlet
• Built-In easy start valve relieves back pressure during engine start up
• Maximum Pressure: 4,050 PSI
• Max. Volume: 10.5 GPM

COMPONENT:
• PA Pulsar 4 Adjustable Unloader Valve 4,050 PSI with EZ Start
• 24” of push-on bypass hose
• 1/4” Male push on fitting
• 3/8” Male push-on fitting
• 3/8M x 3/8M Hex Nipple Steel
• GP Thermal relief valve protects pump from overheating
• GP Duraview water inlet filter with garden hose connection
• 3/8” QC socket
• 3/8” QC plug
• Roll of Teflon tape
• Note: Pump in 2nd picture is not included and kit may look different than shown in picture
• Unloader Must Be Installed Vertically For Proper Operation
• Weight: 5 lb

PA RB 65 Blue Adjustable Spray Wash Down Gun with 1/2" Bsp F Inlet for Food Industry. RB65 suitable for use up to 350 PSI and 16 GPM. Shockproof gun with adjustable conical/pencil jet

Features
• Low pressure washdown gun with conical/pencil jet controlled by the trigger
• Adjustable screw to vary cone width from 0° to 60°
• Covered by semi-housings of non-stainable shockproof plastic, entirely sealed and with 3 rubber protective rings.
• Plastic trigger protected by hand guard
• Minimum fatigue for trigger opening and use
• Internal structure in brass and Sst
• Ergonomic construction

Specifications Sheet

Specifications
• Rated Pressure: 350 PSI
• Rated Flow Rate: 16.0 GPM
• Rated Temp: 195° F.
• Max Temp Continuous Use: 140° F.
• Casing Color: Blue
• Seals Material: Viton
• Piston Material: Brass
• Inlet: 1/2" Bsp F
• GP #: YG1635
• Weight: 33.3 oz

Piston Rod VB 80/400, YU2158
PA # 60.0432.51

Repair Kit PA VB200/150 & GP YU5221, 10x1pcs.

GP # YKITU5221

• Trapped Pressure Unloader
• General # YVB7K
• Maximum Pressure: 3,600 PSI
• Max. Volume: 7.8 GPM
• Adjustable pressure
• Brass body
• Max. Fluid Temp.: 200 degrees F.
• Inlet Ports (1): 3/8" MPT
• Discharge Ports (1): 3/8” FPT
• Bypass Ports (1): 3/8” FPT
• 19.7 OZ. Weight

PA RL 56 Compensating Spray Gun 5,650 PSI 8 GPM. New mechanical device with double connecting rods to guarantee less strain when opening and holding

Features
• Covered by shockproof plastic semi-housings
• Sst seat and ball
• Internal structure in brass and Sst
• Ergonomic construction
• Minimum fatigue for trigger opening and use
• New mechanical opening device with double connecting rods
• New trigger design, rotating on a fixed pin to guarantee better mobility and steadiness
• No fluid passage upon trigger release

Specifications
• Rated Pressure: 5,100 PSI
• Permissible Pressure: 5,650 PSI
• Max Flow: 8.0 GPM
• Max Temp: 320° F.
• Inlet: 3/8" Female NPT
• Outlet: 1/4" Female NPT
• Use # 40.0261.00 matching 41” lance
• Weight: 23.70 oz

PA LS 12 / General Pump YLS12T Foamer with 1L Bottle

Features
• Comfortable Impact Resistant Housing
• Forged Brass Body with Stainless Steel Diffuser
• Adjustable Injector

Specifications
• Rated Pressure: 2,900 PSI
• Permissible Pressure: 3,200 PSI
• Rated Flow: 6.5 GPM
• Nozzle Size: 1.5 mm
• Tank Capacity: 1 Liter
• Rated Temp: 140° F.
• Inlet: G 1/4-F
• Materials: Stainless Steel, Brass, Viton, Plastic
• Replaces # 25.1840.15
• Weight: 17.53 oz

PA 41" Vented Grip S3 350 Stainless Steel Lance for RL 56 Trigger Gun

Specifications
• 41.3” Long stainless steel pipe with vented grips
• Rated Pressure: 5,100 PSI
• Permissible Pressure: 5,650 PSI
• Max Flow: 8.0 GPM
• Max Temp: 320° F.
• Inlet: 1/4" Male
• Outlet: 1/4" Female NPT with nozzle protector
• Overall Length: 43.5”
• Weight: 28.25 oz

#3.0 Red UR32 Turbo Nozzle 5,100 PSI is shrouded in a resilient rubber housing protector

Features
• Offers 0° Impact, but with a 25° pattern
• Unique internal stabilization spring design allows for aim & shoot operation
• Nozzle can be pointed in any direction
• Shock resistant ceramic
• High Strength forged brass housing
• Durable rubber cover

Specifications
• Nozzle Size #3.0
• Max PSI: 5,100
• Max GPM: 9.9
• Max Temp.: 212° F
• Inlet: 1/4" BSP-F
• Minimum for operation: 2.4 GPM at 2,600 PSI
• Weight: 1.0 lbs

Please use Nozzle Chart to determine proper nozzle size

Nozzle Chart

Features
• Offers 0° Impact, but with a 25° pattern
• Unique internal stabilization spring design allows for aim & shoot operation
• Nozzle can be pointed in any direction
• Shock resistant ceramic
• High Strength forged brass housing
• Durable rubber cover

Specifications
• Nozzle Size #6.0
• Max PSI: 5,100
• Max GPM: 9.9
• Max Temp.: 212° F
• Inlet: 1/4" FPT
• Minimum for operation: 2.4 GPM at 2,600 PSI
• Weight: 1.0 lbs

Please use Nozzle Chart to determine proper nozzle size

Nozzle Chart

Features
• Offers 0° Impact, but with a 25° pattern
• Unique internal stabilization spring design allows for aim & shoot operation
• Nozzle can be pointed in any direction
• Shock resistant ceramic
• High Strength forged brass housing
• Durable rubber cover

Specifications
• Nozzle Size #6.5
• Max PSI: 5,100
• Max GPM: 9.9
• Max Temp.: 212° F
• Inlet: 1/4" FPT
• Minimum for operation: 2.4 GPM at 2,600 PSI
• Weight: 1.0 lbs

Please use Nozzle Chart to determine proper nozzle size

Nozzle Chart

Features
• Offers 0° Impact, but with a 25° pattern
• Unique internal stabilization spring design allows for aim & shoot operation
• Nozzle can be pointed in any direction
• Shock resistant ceramic
• High Strength forged brass housing
• Durable rubber cover

Specifications
• Nozzle Size #7.0
• Max PSI: 5,100
• Max GPM: 9.9
• Max Temp.: 212° F
• Inlet: 1/4" FPT
• Minimum for operation: 2.4 GPM at 2,600 PSI
• Weight: 1.0 lbs

Please use Nozzle Chart to determine proper nozzle size

Nozzle Chart

Features
• Offers 0° Impact, but with a 25° pattern
• Unique internal stabilization spring design allows for aim & shoot operation
• Nozzle can be pointed in any direction
• Shock resistant ceramic
• High Strength forged brass housing
• Durable rubber cover

Specifications
• Nozzle Size #8.0
• Max PSI: 5,100
• Max GPM: 9.0
• Max Temp.: 212° F
• Inlet: 1/4" FPT
• Minimum for operation: 2.4 GPM at 2,600 PSI
• Weight: 1.0 lbs

Please use Nozzle Chart to determine proper nozzle size

Nozzle Chart

#4.5 Red PA UR32 / GP YR51K Turbo Nozzle 5,100 PSI is shrouded in a resilient rubber housing protector

Features
• Offers 0° Impact, but with a 25° pattern
• Unique internal stabilization spring design allows for aim & shoot operation
• Nozzle can be pointed in any direction
• Shock resistant ceramic
• High Strength forged brass housing
• Durable rubber cover

Specifications
• Nozzle Size #4.5
• Max PSI: 5,100
• Max GPM: 9.0
• Max Temp.: 212° F
• Inlet: 1/4" NPT-F
• Minimum for operation: 2.4 GPM at 2,600 PSI
• Replaces 25.1690.45
• Weight: 1.0 lbs

Please use Nozzle Chart to determine proper nozzle size

Nozzle Chart

#4.0 Red PA UR32 / GP YR51K Turbo Nozzle 5,100 PSI is shrouded in a resilient rubber housing protector

Features
• Offers 0° Impact, but with a 25° pattern
• Unique internal stabilization spring design allows for aim & shoot operation
• Nozzle can be pointed in any direction
• Shock resistant ceramic
• High Strength forged brass housing
• Durable rubber cover

Specifications
• Nozzle Size #4.0
• Max PSI: 5,100
• Max GPM: 9.0
• Max Temp.: 212° F
• Inlet: 1/4" NPT-F
• Minimum for operation: 2.4 GPM at 2,600 PSI
• Replaces 25.1690.40
• Weight: 1.0 lbs

Please use Nozzle Chart to determine proper nozzle size

Nozzle Chart

#5.5 Red PA UR32 / GP YR51K Turbo Nozzle 5,100 PSI is shrouded in a resilient rubber housing protector

Features
• Offers 0° Impact, but with a 25° pattern
• Unique internal stabilization spring design allows for aim & shoot operation
• Nozzle can be pointed in any direction
• Shock resistant ceramic
• High Strength forged brass housing
• Durable rubber cover

Specifications
• Nozzle Size #5.5
• Max PSI: 5,100
• Max GPM: 9.0
• Max Temp.: 212° F
• Inlet: 1/4" NPT-F
• Minimum for operation: 2.4 GPM at 2,600 PSI
• Replaces 25.1690.55
• Weight: 1.0 lbs

Please use Nozzle Chart to determine proper nozzle size

Nozzle Chart

#3.5 Red PA UR32 / GP YR51K Turbo Nozzle 5,100 PSI is shrouded in a resilient rubber housing protector

Features
• Offers 0° Impact, but with a 25° pattern
• Unique internal stabilization spring design allows for aim & shoot operation
• Nozzle can be pointed in any direction
• Shock resistant ceramic
• High Strength forged brass housing
• Durable rubber cover

Specifications
• Nozzle Size #3.5
• Max PSI: 5,100
• Max GPM: 9.0
• Max Temp.: 212° F
• Inlet: 1/4" NPT-F
• Minimum for operation: 2.4 GPM at 2,600 PSI
• Replaces 25.1690.35
• Weight: 1.0 lbs

Please use Nozzle Chart to determine proper nozzle size

Nozzle Chart

#5.0 Red PA UR32 / GP YR51K Turbo Nozzle 5,100 PSI is shrouded in a resilient rubber housing protector

Features
• Offers 0° Impact, but with a 25° pattern
• Unique internal stabilization spring design allows for aim & shoot operation
• Nozzle can be pointed in any direction
• Shock resistant ceramic
• High Strength forged brass housing
• Durable rubber cover

Specifications
• Nozzle Size #5.0
• Max PSI: 5,100
• Max GPM: 9.0
• Max Temp.: 212° F
• Inlet: 1/4" NPT-F
• Minimum for operation: 2.4 GPM at 2,600 PSI
• Replaces 25.1690.50
• Weight: 1.0 lbs

Please use Nozzle Chart to determine proper nozzle size

Nozzle Chart

PA PR1 / General Pump YPRSWITCHHPL 9,570 PSI Pressure Switch with 360 PSI (Red) activation and 3/8" BSP-M stainless steel inlet. Electro-mechanical device, which, upon reaching a pre-set pressure (360 PSI) , opens or closes an electrical control contact

Specifications
• Activation (Red) PSI: 360
• Max. Voltage: 250
• Max Rated Pressure: 8,700 PSI
• Max Permissible Pressure: 9,570 PSI
• Rated Temp: 195° F
• Max. Curr. Strength: 16 (A) – resistive load - 6 (A) – inductive load
• Electrical insulation: 55 IP
• Connection Material: Stainless Steel
• Cable Length: 47" (1200 mm)
• Electric Wire: 3 x 1 mm
• Inlet: 3/8" Bsp M
• Weight: 10.3 oz.

• Trapped Pressure Unloader
• General # YVB3KA, Series 51 & 60 Pumps
• Maximum Pressure: 3,200 PSI
• Max. Volume: 6.5 GPM
• Adjustable pressure
• Brass body
• Max. Fluid Temp.: 195 degrees F.
• Inlet Ports (1): 3/8" MPT
• Discharge Ports (1): 3/8” MPT
• Bypass Ports (1): 3/8” FPT
• 14.7 OZ. Weight