General Pump

General Pump 100720 Clutch w/Mounting Plate 44, 50, 63 and 58 (ES) Series, 12V, Single Groove. Mobile Clutch for 24mm Solid Shaft Pump

Features:
• Solid forged rotor. A one-piece solid forged rotor means no chance of internal parts separation. They have an even wall thickness around the coil which gives optimum flux distribution, maximizing torque.
• Different coil voltages available. 12 volt is the most common; 24 volt clutches are also available.
• High temperature, longer-life grease. Our special long-life grease has shown a significant improvement in life over other standard high temp greases.
• E-coating. Where possible, all parts in the clutch are e-coated to give maximum corrosion protection.
• High-temperature epoxy coil. To help prevent failure from vibration and outside contaminants, all coils are sealed in the coil shell with a high-temperature epoxy coating.
• Forged machined pulley. All GP models use a heavy-duty machined pulley. A stronger pulley resists damage

Data Sheet

Specifications:
• Pulley Size & Type: 7" - A Groove, 24mm Shaft
• Width: 2.25"
• Torque After Burnishing: 75 - 95 lbs.
• Power Requirement: 12V 47 Watts
• Weight: 8.0 lbs

General Pump 100719 Clutch w/Mounting Plate 47, 66 and 59(ES) Series, 24V, Dual Groove. Mobile Clutch for 24mm Solid Shaft Pump

Features:
• Solid forged rotor. A one-piece solid forged rotor means no chance of internal parts separation. They have an even wall thickness around the coil which gives optimum flux distribution, maximizing torque.
• Different coil voltages available. 12 volt is the most common; 24 volt clutches are also available.
• High temperature, longer-life grease. Our special long-life grease has shown a significant improvement in life over other standard high temp greases.
• E-coating. Where possible, all parts in the clutch are e-coated to give maximum corrosion protection.
• High-temperature epoxy coil. To help prevent failure from vibration and outside contaminants, all coils are sealed in the coil shell with a high-temperature epoxy coating.
• Forged machined pulley. All GP models use a heavy-duty machined pulley. A stronger pulley resists damage

Data Sheet

Specifications:
• Pulley Size & Type: 7" - A Groove, 24mm Shaft
• Width: 2.25"
• Torque After Burnishing: 75 - 95 lbs.
• Power Requirement: 24V 45.6 Watts
• Weight: 8.0 lbs

General Pump 100720 Clutch w/Mounting Plate 44, 50, 63 and 58 (ES) Series, 24V, Dual Groove. Mobile Clutch for 24mm Solid Shaft Pump

Features:
• Solid forged rotor. A one-piece solid forged rotor means no chance of internal parts separation. They have an even wall thickness around the coil which gives optimum flux distribution, maximizing torque.
• Different coil voltages available. 12 volt is the most common; 24 volt clutches are also available.
• High temperature, longer-life grease. Our special long-life grease has shown a significant improvement in life over other standard high temp greases.
• E-coating. Where possible, all parts in the clutch are e-coated to give maximum corrosion protection.
• High-temperature epoxy coil. To help prevent failure from vibration and outside contaminants, all coils are sealed in the coil shell with a high-temperature epoxy coating.
• Forged machined pulley. All GP models use a heavy-duty machined pulley. A stronger pulley resists damage

Data Sheet

Specifications:
• Pulley Size & Type: 7" - A Groove, 24mm Shaft
• Width: 2.25"
• Torque After Burnishing: 75 - 95 lbs.
• Power Requirement: 24V 45.6 Watts
• Weight: 8.0 lbs

1,500 PSI 2.11 GPM General TT9061EBF Direct Couple to Electric Motors (NEMA 56C)

Features:
• Forged brass manifold with exclusive lifetime warranty
• Die-cast annodized aluminum, oil-bath crankcase
• Solid ceramic plungers with continuously lubricated packings
• The original Interpump unitized, stainless steel, K01 inlet and outlet valves
• Ideal for all general cleaning, RO and misting applications
• Comes standard with NEMA 56C electric motor mounting flange
• Also available in “L” left-handed versions

Specifications Sheet

Specifications:
• Maximum Volume: 2.11 GPM
• Maximum Discharge Pressure: 1,500 PSI
• Maximum Pump Speed: 3,400 RPM
• Maximum Inlet Pressure: 125 PSI
• Oil Capacity: 11.2 oz.
• Maximum Fluid Temperature: 165°F
• Inlet Port Thread: 3/8-19 BSPP-F
• Discharge Port Thread: 1/4-19 BSPP-F
• Shaft Diameter 5/8 in. / 16 mm
• Horespower: 2.2 EBHP
• Weight 12.0 lbs.

1,500 PSI 2.11 GPM General TT9051EBF Direct Couple to Electric Motors (NEMA 56C)

Features:
• Forged brass manifold with exclusive lifetime warranty
• Die-cast annodized aluminum, oil-bath crankcase
• Solid ceramic plungers with continuously lubricated packings
• The original Interpump unitized, stainless steel, K01 inlet and outlet valves
• Ideal for all general cleaning, RO and misting applications
• Comes standard with NEMA 56C electric motor mounting flange
• Also available in “L” left-handed versions

Specifications Sheet

Specifications:
• Maximum Volume: 2.11 GPM
• Maximum Discharge Pressure: 1,500 PSI
• Maximum Pump Speed: 1,750 RPM
• Maximum Inlet Pressure: 125 PSI
• Oil Capacity: 11.2 oz.
• Maximum Fluid Temperature: 165°F
• Inlet Port Thread: 3/8-19 BSPP-F
• Discharge Port Thread: 1/4-19 BSPP-F
• Shaft Diameter 5/8 in. / 16 mm
• Horespower: 2.2 EBHP
• Weight 12.0 lbs.

General EZ4040G 4000PSI, 4.0GPM Pump is designed to direct drive on gasoline engines ranging from 9 -13 HP

Features:
• Standard SAE J609 gasoline mounting flange for up to 13 hp engines
• Forged brass manifold with an exclusive lifetime warranty and 3:1 hydrostatic rating
• Die-cast, anodized aluminum oil-bath crankcase
• Innovative one-piece plunger design to eliminate water entering crankcase
• Premium roller bearing
• 5% reduction in crankcase load compared to standard 3,000 PSI, 15 mm pumps
• Unitized stainless steel inlet and discharge valves

Specifications:
• Triplex Plunger Pump
• Direct Drive with Gas Flange 9.0-13.0 HP SAE
• Max. Volume: 4.0 GPM
• Max. Discharge Pressure: 4,000 PSI
• Max. Pump Speed: 3,400 RPM
• Shaft Diameter: 1” Hollow
• Max. Horsepower Requirements: 14.54 GHP
• Max. Fluid Temp.: 165 degrees F.
• Inlet Ports (2): 1/2-14 BSPP-F
• Discharge Ports (2): 3/8-19 BSPP-F
• Drive Side: Standard right
• Note: Item for sale is PUMP ONLY as shown in picture and does not include unloader which is required for proper operation
• Weight: 20.0 lb.

General Pump 2103410 Electric Hose Reel Motor Kit. Fits DHRA Hose Reels

FEATURES
• Allows for effortless rewinding of hose
• Free spin allows for easy pulling out of hose
• Durable powder coated finish
• Stainless steel hardware
• Long lasting hardened gears

SPECIFICATIONS
• Works with DHRA50150, DHRA50300 & DHRA50450 A Frame Hose Reels
• Voltage 12V DC
• Hose Reel Not Included
• Weight 21 lbs

2,610 PSI 2.9 GPM General PMRET1506G6 Direct Drive Pump Made Ready W/ PULSAR4KHPEZ EZ Start Unloader. Pump is ready to use right out of the box

PUMP:
• General ET1506G6 Pump with SAE J609A Gas Flange
• Direct Drive with Gas Flange 5.0-7.0 HP SAE
• Max. Volume: 2.9 GPM
• Max. Discharge Pressure: 2,610 PSI
• Max. Pump Speed: 3,400 RPM
• Shaft Diameter: 3/4” Hollow
• Max. Horsepower Requirements: 6.9 GHP
• Max. Fluid Temp.: 165º F
• New “HR” anti-corrosion surface treatment on manifold
• Solid ceramic plungers

COMPONENTS:
• General ET1506G6 Triplex Plunger Pump
• PULSAR4KHPEZ EZ Start Unloader 4,050 PSI, 10 GPM
• Thermal relief valve
• 3/8” Hose Barb and Clamp Keeps Hose Secure and Sealed
• 3/4” Garden Hose Inlet Fitting with 1/4” Side Port
• 3/8” QC brass socket and 3/8” QC Plug Included
• Mounting bolts
• Note: Pumps are not tested prior to shipping and unloader will need to be adjusted
• Weight: 14.90 lb

General ET1506E34 2,610 PSI 2.9 GPM Direct Drive Pump flanged to direct couple on electric NEMA 56 C motors

Features:
• “HR” anti-corrosion surface treatment on manifold
• New generation seal package
• Dust protection chamber
• Solid ceramic plungers
• Oversized plunger guide
• Optimized inlet and outlet valves
• Oversized crankcase Hollow shaft, flanged for direct couple to electric motors (NEMA56C)

Specifications:
• Max. Volume: 2.9 GPM
• Max. Discharge Pressure: 2,610 PSI
• Max. Horsepower Requirements: 5.2 EBHP
• Max. Pump Speed: 3,400 RPM
• Max. Fluid Temp.: 165º F
• Oil Capacity: 8.5 oz
• Inlet Port Thread: 1/2"-14 BSP-F
• Discharge Port Thread: 3/8"-19 BSP-F
• Shaft Diameter: 5/8” Hollow
• Dimensions – Nominal: 7.3" x 7.4" x 5.5"
• Weight: 11.0 lb

General ET1506E34 2,610 PSI 2.9 GPM (Left Handed) Direct Drive Pump flanged to direct couple on electric NEMA 56 C motors

Features:
• “HR” anti-corrosion surface treatment on manifold
• New generation seal package
• Dust protection chamber
• Solid ceramic plungers
• Oversized plunger guide
• Optimized inlet and outlet valves
• Oversized crankcase Hollow shaft, flanged for direct couple to electric motors (NEMA56C)

Specifications:
• Max. Volume: 2.9 GPM
• Max. Discharge Pressure: 2,610 PSI
• Max. Horsepower Requirements: 5.2 EBHP
• Max. Pump Speed: 3,400 RPM
• Max. Fluid Temp.: 165º F
• Oil Capacity: 8.5 oz
• Inlet Port Thread: 1/2"-14 BSP-F
• Discharge Port Thread: 3/8"-19 BSP-F
• Shaft Diameter: 5/8” Hollow
• Dimensions – Nominal: 7.3" x 7.4" x 5.5"
• Weight: 11.0 lb

General ET1505E34 2,610 PSI 2.1 GPM Direct Drive Pump flanged to direct couple on electric NEMA 56 C motors

Features:
• “HR” anti-corrosion surface treatment on manifold
• New generation seal package
• Dust protection chamber
• Solid ceramic plungers
• Oversized plunger guide
• Optimized inlet and outlet valves
• Oversized crankcase Hollow shaft, flanged for direct couple to electric motors (NEMA56C)

Specifications:
• Max. Volume: 2.1 GPM
• Max. Discharge Pressure: 2,610 PSI
• Max. Horsepower Requirements: 3.7 EBHP
• Max. Pump Speed: 3,400 RPM
• Max. Fluid Temp.: 165º F
• Oil Capacity: 8.5 oz
• Inlet Port Thread: 1/2"-14 BSP-F
• Discharge Port Thread: 3/8"-19 BSP-F
• Shaft Diameter: 5/8” Hollow
• Dimensions – Nominal: 7.3" x 7.4" x 5.5"
• Weight: 11.0 lb

General Pump ZH1520 Trapped Pressure Unloader Valve 2,465 PSI 52.8 GPM 1” NPT-F

Features
• Suitable for Industrial use
• Provisions for Panel Mounting
• Suitable for Industrial use
• Single bypass port
• Extremely reliable
• Easy maintenance

Specifications Sheet

Specifications
• Max Volume: 52.8 GPM
• Min Volume: 5.28 GPM
• Maximum Operating Pressure: 2,465 PSI
• Maximum Temperature: 185° F
• Inlet Port: 1" NPT-F
• Outlet Port: 1" NPT-F
• Bypass Port: 1" NPT-F
• Dimensions: 8.27” x 5.07” x 1.81”
• VRP175, VRP 175
• Weight: 4.4 Lbs

General Pump DHRA50450 3/8" x 450' or 1/2" x 375' or 5/8” x 300’ (garden hose). "A" Frame Industrial Hose Reel. Rated 5,000 PSI and up to 250° F. Ideal for use with pressure washers, sewer jetters, lawn & tree sprayers, etc. Can be used as is or can be mounted to portable cart or stacked

FEATURES
• Direct hand-crank rewind with pin lock
• Solid steel construction
• Durable gray high-gloss powder coated finish
• Full flow stainless steel swivel
• Friction brake
• Switchable swivel/handle
• HD steel welded frame
• HD sealed axle bearings
• Includes one D10032 Fitting 3/4” GH X 1/2 NPT-M

DHRA Spec Sheet

SPECIFICATIONS
• Capacity 3/8" Pressure Washer / Sewer Hose: 450’
• Capacity 5/8" Garden Hose: 325’
• Capacity 3/4" Garden Hose: 250’
• Max. PSI: 5,000
• Max Temp: 250° F.
• Color: Black
• Inlet: 1/2 NPT-F (Bushing Included, 1/2 NPT-M x 3/8 NPT-F)
• Outlet: 1/2 NPT-F (Bushing Included, 1/2 NPT-M x 3/8 NPT-F)
• Carton Dimensions: 26” x 20” x 18”
• Gross Weight 47.6 lbs