P.A. Srl

PA RL 56 Compensating Spray Gun 5,650 PSI 8 GPM. New mechanical device with double connecting rods to guarantee less strain when opening and holding

Features
• Covered by shockproof plastic semi-housings
• Sst seat and ball
• Internal structure in brass and Sst
• Ergonomic construction
• Minimum fatigue for trigger opening and use
• New mechanical opening device with double connecting rods
• New trigger design, rotating on a fixed pin to guarantee better mobility and steadiness
• No fluid passage upon trigger release

Specifications
• Rated Pressure: 5,100 PSI
• Permissible Pressure: 5,650 PSI
• Max Flow: 8.0 GPM
• Max Temp: 320° F.
• Inlet: 3/8" Female NPT
• Outlet: 1/4" Female NPT
• Use # 40.0261.00 matching 41” lance
• Weight: 23.70 oz

• Trapped Pressure Unloader
• General # YVB7K
• Maximum Pressure: 3,600 PSI
• Max. Volume: 7.8 GPM
• Adjustable pressure
• Brass body
• Max. Fluid Temp.: 200 degrees F.
• Inlet Ports (1): 3/8" MPT
• Discharge Ports (1): 3/8” FPT
• Bypass Ports (1): 3/8” FPT
• 19.7 OZ. Weight

Repair Kit PA VB200/150 & GP YU5221, 10x1pcs.

GP # YKITU5221

Piston Rod VB 80/400, YU2158
PA # 60.0432.51

PA RB 65 Blue Adjustable Spray Wash Down Gun with 1/2" Bsp F Inlet for Food Industry. RB65 suitable for use up to 350 PSI and 16 GPM. Shockproof gun with adjustable conical/pencil jet

Features
• Low pressure washdown gun with conical/pencil jet controlled by the trigger
• Adjustable screw to vary cone width from 0° to 60°
• Covered by semi-housings of non-stainable shockproof plastic, entirely sealed and with 3 rubber protective rings.
• Plastic trigger protected by hand guard
• Minimum fatigue for trigger opening and use
• Internal structure in brass and Sst
• Ergonomic construction

Specifications Sheet

Specifications
• Rated Pressure: 350 PSI
• Rated Flow Rate: 16.0 GPM
• Rated Temp: 195° F.
• Max Temp Continuous Use: 140° F.
• Casing Color: Blue
• Seals Material: Viton
• Piston Material: Brass
• Inlet: 1/2" Bsp F
• GP #: YG1635
• Weight: 33.3 oz

PA Pulsar 4 Unloader Plumbing Kit for Pressure Washer Pump with EZ Start– 4,050 PSI Max. This unloader kit has all the components to make installation easy

Specifications:
• Works with pumps that have 1/2” FPT inlet and 3/8” FPT Outlet
• Built-In easy start valve relieves back pressure during engine start up
• Maximum Pressure: 4,050 PSI
• Max. Volume: 10.5 GPM

COMPONENT:
• PA Pulsar 4 Adjustable Unloader Valve 4,050 PSI with EZ Start
• 24” of push-on bypass hose
• 1/4” Male push on fitting
• 3/8” Male push-on fitting
• 3/8M x 3/8M Hex Nipple Steel
• GP Thermal relief valve protects pump from overheating
• GP Duraview water inlet filter with garden hose connection
• 3/8” QC socket
• 3/8” QC plug
• Roll of Teflon tape
• Note: Pump in 2nd picture is not included and kit may look different than shown in picture
• Unloader Must Be Installed Vertically For Proper Operation
• Weight: 5 lb

PA RB 65 Blue Adjustable Spray Wash Down Gun with 1/2" Npt F Inlet for Food Industry. RB65 suitable for use up to 350 PSI and 16 GPM. Shockproof gun with adjustable conical/pencil jet

Features
• Low pressure washdown gun with conical/pencil jet controlled by the trigger
• Adjustable screw to vary cone width from 0° to 60°
• Covered by semi-housings of non-stainable shockproof plastic, entirely sealed and with 3 rubber protective rings.
• Plastic trigger protected by hand guard
• Minimum fatigue for trigger opening and use
• Internal structure in brass and Sst
• Ergonomic construction

Specifications Sheet

Specifications
• Rated Pressure: 350 PSI
• Rated Flow Rate: 16.0 GPM
• Rated Temp: 195° F.
• Max Temp Continuous Use: 140° F.
• Casing Color: Blue
• Seals Material: Viton
• Piston Material: Brass
• Inlet: 1/2" Npt F
• GP #: YG1635N
• Weight: 33.3 oz

PA RB 65 Blue Adjustable Spray Wash Down Gun with Inlet Swivel for Food Industry. RB65 suitable for use up to 350 PSI and 16 GPM. Shockproof gun with adjustable conical/pencil jet

Features
• Low pressure washdown gun with conical/pencil jet controlled by the trigger
• Adjustable screw to vary cone width from 0° to 60°
• Covered by semi-housings of non-stainable shockproof plastic, entirely sealed and with 3 rubber protective rings.
• Plastic trigger protected by hand guard
• Minimum fatigue for trigger opening and use
• Internal structure in brass and Sst
• Ergonomic construction
• Inlet swivel connection

Specifications Sheet

Specifications
• Rated Pressure: 350 PSI
• Rated Flow Rate: 16.0 GPM
• Rated Temp: 195° F.
• Max Temp Continuous Use: 140° F.
• Casing Color: Blue
• Seals Material: Viton
• Piston Material: Brass
• Swivel Inlet: 1/2" Bsp F
• GP #: YG1635S
• Weight: 37.39 oz

PA RB 65 Red Adjustable Spray Wash Down Gun with Inlet Swivel for Food Industry. RB65 suitable for use up to 350 PSI and 16 GPM. Shockproof gun with adjustable conical/pencil jet and Stainless Steel Piston

Features
• Low pressure washdown gun with conical/pencil jet controlled by the trigger
• Adjustable screw to vary cone width from 0° to 60°
• Covered by semi-housings of non-stainable shockproof plastic, entirely sealed and with 3 rubber protective rings.
• Plastic trigger protected by hand guard
• Minimum fatigue for trigger opening and use
• Internal structure in brass and Sst
• Ergonomic construction
• Inlet swivel connection

Specifications Sheet

Specifications
• Rated Pressure: 350 PSI
• Rated Flow Rate: 16.0 GPM
• Rated Temp: 195° F.
• Max Temp Continuous Use: 140° F.
• Casing Color: Red
• Seals Material: Viton
• Piston Material: aisi303 Sst
• Swivel Inlet: 1/2" Bsp F
• GP #: YG1635SR
• Weight: 37.39 oz

PA VB 85/310 Rv and General YUB21405 blue spring trapped pressure unloader valve. At gun closure, the waterflow is discharged in bypass reducing the pressure in the system upstream of the valve

Featuring:
• Dynamic seals made up of O-ring and Back-up ring
• Optimized internal passages that guarantee reduced pressure loss
• Anti-rotation device of the piston positioned inside the valve and obtained by an hexagonal sector of the piston itself
• O-rings of the fittings positioned upstream to the thread : no risk of fittings ejected in case of overpressure
• Double feed connection
• Suitable for recycled water and strong detergents

Data Sheet

Specifications:
• Spring Color: Blue
• Permissible Pressure: 4,500 PSI
• Rated Pressure: 4,050 PSI
• Rated Flow Rate: 21.0 GPM
• Rated Temperature: 195° F
• Inlet Ports (2): 1/2" NPT F
• Outlet Port: 1/2” NPT F
• Bypass Port: 1/2” NPT F
• Replaces: 60.0485.65, VB 85/280, 60.0400.65, VB 80/280 and YUB2140
• Weight: 40.63 Oz

PA VB 85/180 Rv and General YUB21235 white spring trapped pressure unloader valve. At gun closure, the waterflow is discharged in bypass reducing the pressure in the system upstream of the valve

Featuring:
• Dynamic seals made up of O-ring and Back-up ring
• Optimized internal passages that guarantee reduced pressure loss
• Anti-rotation device of the piston positioned inside the valve and obtained by an hexagonal sector of the piston itself
• O-rings of the fittings positioned upstream to the thread : no risk of fittings ejected in case of overpressure
• Double feed connection
• Suitable for recycled water and strong detergents

Data Sheet

Specifications:
• Spring Color: White
• Permissible Pressure: 2,600 PSI
• Rated Pressure: 2,300 PSI
• Rated Flow Rate: 21.0 GPM
• Rated Temperature: 195° F
• Inlet Ports (2): 1/2" NPT F
• Outlet Port: 1/2” NPT F
• Bypass Port: 1/2” NPT F
• Replaces: 60.0485.05, VB 85/160, 60.0400.05, VB 80/150 and YUW2121
• Weight: 40.63 Oz

PA Pulsar 4 Unloader Plumbing Kit for Pressure Washer Pump with Safety Relief and EZ Start– 4,050 PSI Max. This unloader kit has all the components to make installation easy

Specifications:
• Works with pumps that have 1/2” FPT inlet and 3/8” FPT Outlet
• Safety relief vale protects equipment and people with adjustable “Pop Off” protection
• Built-In easy start valve relieves back pressure during engine start up
• Maximum Pressure: 4,050 PSI
• Max. Volume: 10.5 GPM

COMPONENT:
• PA Pulsar 4 Adjustable Unloader Valve 4,050 PSI with EZ Start
• GP Safety pressure relief valve with adjustable range: 1,000 - 6,000 PSI
• 3/8” Steel street elbow
• 24” of push-on bypass hose
• 1/4” Male push on fitting
• 3/8” Male push-on fitting
• 3/8M x 3/8M Hex Nipple Steel
• GP Thermal relief valve protects pump from overheating
• GP Duraview water inlet filter with garden hose connection
• 3/8” QC socket
• 3/8” QC plug
• Roll of Teflon tape
• Note: Pump in 2nd picture is not included and kit may look different than shown in picture
• Unloader Must Be Installed Vertically For Proper Operation
• Weight: 5 lb

PA RLW 40 / General Pump YG3000DS Dump Gun with 16" Lance 3,050 PSI 10.5 GPM. Low pressure weeping gun; High pressure function by trigger operation

Features
• Covered by shockproof plastic semi-housings
• High/low pressure gun with double concentric outlet
• Delrin shutter
• Internal structure in brass and stainless steel
• Ergonomic construction
• Minimum fatigue for trigger opening

Specifications
• Rated Pressure: 2,750 PSI
• Permissible Pressure: 3,050 PSI
• Lance: 15.74”
• Max Flow: 10.5 GPM
• Max Temp: 140° F.
• Inlet: 3/8" NPT-F
• Outlet: 1/8" NPT-F
• Weight: 33.44 oz

Features:
• Assembly equipped with a high pressure proof compensation
• Compact dimensions
• Sturdy steel and brass construction
• Adjustable locknut to control max pressure
• Red nylon knob
• Easy maintenance

Specifications:
• Rated Pressure: 5,100 PSI
• Permissible Pressure: 5,600 PSI
• Rated Flow Rate: 10.5 GPM
• Rated Temperature: 195° F
• Adjustable pressure
• Forged brass body
• Inlet Port: 3/8" MPT
• Outlet Port: 3/8” FPT
• Bypass Port: 1/2” FPT
• Gauge Port: 1/4” FPT
• Weight: 32.5 oz

PA FL 12 / General Pump YFL12 4,500 PSI 26.4 GPM Flow Switch with 3/4" NPT-F inlet

Features
• Electro-mechanical device in which the fluid passage moves a magnetized piston that opens an electric circuit. DN 20
• Magnetic drive obtained by the plunging piston movement
• Electrical insulation: class IP55
• Magnetic probe casing made of antiflame material

Specifications
• Rated Pressure: 4,000 PSI
• Permissible Pressure: 4,500 PSI
• Max Flow Rate: 26.4 GPM
• Activation Flow Rate: Horizontal: 2.0 GPM
• Activation Flow Rate: Vertical: 3.3 GPM
• Max Working Temp: 165° F
• Max. Voltage: 230 V
• Max. Curr. Strength: 3 A
• Cable Length: 49.2" (1250 mm)
• Electrical insulation: 55 IP - 0
• Materials: Brass, Stainless Steel, Buna-N, Plastic
• Inlet: 3/4" NPT-F
• Outlet: 3/4" NPT-F
• Weight: 34.4 oz.

Repair Kit, YG2953, RL19, RL204
PA # 30.4046.24

Features:
• Assembly equipped with a high pressure proof compensation
• Compact dimensions
• Sturdy steel and brass construction
• Fixing system for the max. and min. pressure setting
• Sst seat for check valve, replaceable
• Easy maintenance

Specifications:
• Rated Pressure: 5,100 PSI
• Permissible Pressure: 5,600 PSI
• Rated Flow Rate: 10.5 GPM
• Rated Temperature: 195° F
• Adjustable pressure
• Forged brass body
• Inlet Port: 3/8" MPT
• Outlet Port: 3/8” FPT
• Bypass Port: 1/2” FPT
• Gauge Port: 1/4” FPT
• Weight: 31.04 oz

PA RLW 40 / General Pump YG3000D Dump Gun with 40" Lance 3,050 PSI 10.5 GPM. Low pressure weeping gun; High pressure function by trigger operation

Features
• Covered by shockproof plastic semi-housings
• High/low pressure gun with double concentric outlet
• Delrin shutter
• Internal structure in brass and stainless steel
• Ergonomic construction
• Minimum fatigue for trigger opening

Specifications
• Rated Pressure: 2,750 PSI
• Permissible Pressure: 3,050 PSI
• Lance: 39.40”
• Max Flow: 10.5 GPM
• Max Temp: 140° F.
• Inlet: 3/8" NPT-F
• Outlet: 1/8" NPT-F
• Weight: 48.04 oz

• Automatic Pressure Compensating Unloader Valve
• General # YU3678
• Must Be Mounted Vertically
• Reduces trapped pressure to 25% of operating pressure when unloading
• Allows easier trigger gun pull
• Maximum Pressure: 3,600 PSI
• Max. Volume: 7.8 GPM
• Adjustable pressure
• Brass body
• Max. Fluid Temp.: 194 degrees F.
• Inlet Ports (1): 3/8" FPT
• Discharge Ports (1): 3/8” FPT
• Bypass Ports (1): 3/8” FPT
• 40.0 OZ. Weight

#10.0 Green PA UR40 / GP YR58K Turbo Nozzle 5,800 PSI with nozzle and seat in tungsten carbide

Features
• Offers 0° Impact, but with a 25° pattern
• Reduced vibrations for greater comfort during use
• Shock absorption thanks to the rubber protection
• Nozzle and seat in tungsten carbide
• High Strength forged brass housing
• The nozzle can be started in any position thanks to the patented system with internal spring, which eliminates clearance between the seat and the nozzle

Specifications
• Nozzle Size #10.0
• Max PSI: 5,800
• Min Operating PSI: 2,600
• Max Temp.: 140° F
• Min Temp.: 41° F
• Inlet: 1/4" BSP-F
• Weight: 15.6 oz

Please use Nozzle Chart to determine proper nozzle size

Nozzle Chart