Fairview USA Inc.

Fairview FLEX-DOT 1485 Series 5/8" x 250' Red Reinforced Air Brake Tubing - Type 3B. Air brake tube is designed for use with truck, trailer and other mobile air brake and auxiliary systems. This lightweight, flexible and UV stabilized tube is highly resistant to abrasion, oil, grease and road salt

MEETS OR EXCEEDS: D.O.T. F.M.V.S.S. 106 S.A.E. J844 TEST REQUIREMENTS

FLEX-DOT 1485 Series Air Brake Tube is MADE IN CANADA

Compliance:
• All series 1485 tube are designed in compliance with the revised DOT 106 standard which took effect December 24th, 2007
• Fairview’s FLEX-DOT air brake tube is dimensionally identical to the previous air brake tube described in SAE J844 Type A and Type B, and is compatible with the same fittings. Both compression and push-to-connect fittings can be used with FLEX-DOT tube in all applications other than truck to trailer connections, in which push-to-connect fittings are not suitable

Materials:
• Both the core tube and jacket are comprised of a custom formulated elastomer, offering exceptional heat aging, oil resistance, and low temperature flexibility, when compared to previous nylon materials
• With its improved flexibility at all temperatures, the FLEX-DOT tube is easier to install in tight quarters
• The special compound was custom formulated for this application and offers exceptional flexibility even at very low temperatures. Unlike traditional all-nylon tube, the FLEX-DOT elastomer hose can still be flexed at -65C (-85F)

SPECIFICATION SHEET FLEX-DOT SERIES 1485

INSTALLATION DATA SHEET

Specifications:
• Nominal OD: 5/8”
• Inside Diameter ID: 0.441”
• Wall Thickness: 0.092" +/-0.005"
• Length: 250’
• Temperature: -85°F to +200°F, -65°C to +93°C
• Type: 3B, Reinforced
• Color: Red
• Working Pressure: 225 PSI
• Minimum Burst @ 68°F: 900 PSI
• Supported Bend Radius: 2.50”
• Unsupported Bend Radius: 3.00”
• Approx. Weight: 23.35 lbs

Fairview GAS-FLO® GR-630B Single Stage Hi-Pressure RV Camper LP / Propane Gas Regulator 1/4 FPT 500,000 BTU/HR. This Fairview's GAS-FLO® High Pressure LP Regulator has outlet setting 30 PSIG

Applications:
• Ideally suited for applications where pounds instead of inches of w.c. are required
• Factory pre-set 30 PSIG
• Used on Gas Grills, Smokers and Fish Cookers
• UL Listed

TECHNICAL DATA SHEET

Specifications:
• Inlet: 1/4 FPT
• Outlet: 1/4 FPT
• Outlet Pressure (Set Point): 30 PSIG
• Inlet Pressure: 100 PSIG
• Capacity At 10% Droop from set point BTU/Hr: 500,000
• TO BE INSTALLED BY LICENSED GAS FITTERS ONLY
• Weight: 0.45 lbs

Fairview GAS-FLO® GR-800 Single Stage Low Pressure LP Gas Regulator 1/4 FPT In x 3/8 FPT Out 175,000 BTU/HR. Fairview's GAS-FLO® Single Stage, Compact LP-Gas Regulators are rated to 175,000 BTU/hr

Features:
• The model GR-800 regulator incorporates a drip lip vent and is ideally suited for use with portable appliances
• Zinc Die Cast
• Molded Rubber Diaphragms
• Underwriters Laboratories Listed
• Integral Pressure Relief

TECHNICAL DATA SHEET

Specifications:
• Inlet: 1/4 FPT
• Outlet: 3/8 FPT
• Vent Position: Drip Lip Vent Above Outlet
• Capacity BTU/Hr Propane: 175,000
• TO BE INSTALLED BY LICENSED GAS FITTERS ONLY
• Weight: 0.60 lbs

Fairview GAS-FLO® GR-866 Single Stage Low Pressure LP Gas Regulator Black QCC1 In x 3/8 FPT Out. Fairview's GAS-FLO® Single Stage, Compact LP-Gas Regulators are rated to 175,000 BTU/hr

Features:
• GR-800 regulator with QCC1 (1-5/16 F. Acme)
• The model GR-800 regulator incorporates a drip lip vent and is ideally suited for use with portable appliances
• Zinc Die Cast
• Molded Rubber Diaphragms
• Underwriters Laboratories Listed
• Integral Pressure Relief

TECHNICAL DATA SHEET

Specifications:
• Inlet: QCC1 (1-5/16 F. Acme)
• Outlet: 3/8 FPT
• Vent Position: Drip Lip Vent Above Outlet
• Capacity BTU/Hr Propane: 175,000
• TO BE INSTALLED BY LICENSED GAS FITTERS ONLY
• Weight: 0.75 lbs

Fairview QD-GMC8-8F GAS-FLO™ 1/2” Coupler x 1/2” FPT LPG/Nat. Gas Quick Disconnect. Fairview's CSA LPG/Nat. Gas Couplers are CSA Certified up to 60 PSI WP

Features:
• C.S.A. GAS INTERCHANGE QUICK DISCONNECTS (QD-GMC)
• CSA certified to Z21.41/CSA6.9 for Natural Gas and LP-Gas – air mixtures
• All QD-GMC Quick Disconnects Rated To 60 P.S.I.
• QD-GMC Sizes 1/4, 3/8, 1/2 & 3/4 Quick Disconnects Are Rated To A Temperature -40°F

TECHNICAL DATA SHEET

INSTALLATION INSTRUCTIONS

Specifications:
• Coupler (Body Size): 1/2
• Female Pipe Thread: 1/2
• Quick Disconnect BTU Capacity: 120,000
• Material: Brass
• Weight: 7.4 oz

Fairview GAS-FLO™ BV5221-D 1/2" FPT Forged Full Port Brass Ball Valve 600 WOG. Fairview's Brass Female Pipe Gas Cocks are CSA certified to 5 P.S.I. (-40°) from the appliance to the meter

TECHNICAL DATA SHEET

INSTALLATION DATA SHEET

Features:
• For Indoor/Outdoor applications. C.S.A. Certified forged brass ball valves for Natural and Propane Gas (vapor)
• Brass valves for use in W.O.G. = Water, Oil and Gas 
• Full Port
• Blowout-Proof Stem
• PTFE Seats
• CSA certified to 5 P.S.I.

Specifications:
• W.O.G: 600
• Pipe Size: 1/2” FPT
• Connection Type: Female to Female
• Materials: Aluminum, Brass, NBR, PTFE, Steel
• Operating temperature: -40°F to +125°F (-40°C to +52°C)
• Weight: 0.33 lbs

Fairview QD-GMN8-8F GAS-FLO™ 1/2” Nipple x 1/2” FPT LPG/Nat. Gas Quick Disconnect. Fairview's CSA LPG/Nat. Gas Nipples are CSA Certified up to 60 PSI WP

Features:
• C.S.A. GAS INTERCHANGE QUICK DISCONNECTS (QD-GMC)
• CSA certified to Z21.41/CSA6.9 for Natural Gas and LP-Gas – air mixtures
• QD-GMC Quick Disconnects Rated To 60 P.S.I.
• QD-GMC Sizes 1/4, 3/8, 1/2 & 3/4 Quick Disconnects Are Rated To A Temperature -40°F

TECHNICAL DATA SHEET

INSTALLATION INSTRUCTIONS

Specifications:
• Nipple (Body Size): 1/2
• Female Pipe Thread: 1/2
• Quick Disconnect BTU Capacity: 120,000
• Material: Brass
• Weight: 2.8 oz

Fairview GAS-FLO™ BV5042-8 1/2" Flare Tube Forged Full Port Brass Ball Valve 600 WOG. Fairview's Brass Flare Union Gas Cocks are CSA certified to 5 P.S.I. (-40°) from the appliance to the meter

TECHNICAL DATA SHEET

INSTALLATION DATA SHEET

Features:
• For Indoor/Outdoor applications. C.S.A. Certified forged brass ball valves for Natural and Propane Gas (vapor)
• Brass valves for use in W.O.G. = Water, Oil and Gas 
• Full Port
• Blowout-Proof Stem
• PTFE Seats
• CSA certified to 5 P.S.I. FROM APPLIANCE TO METER

Specifications:
• W.O.G: 600
• Flare Tube Size: 1/2”
• Connection Type: Flare Tube to Flare Tube
• Materials: Aluminum, Brass, NBR, PTFE, Steel
• Operating temperature: -40°F to +125°F (-40°C to +52°C)
• Weight: 0.30 lbs

Fairview GAS-FLO™ BV5046-8D 1/2" Flare Tube to 1/2” FPT Forged Full Port Brass Ball Valve 600 WOG. Fairview's Brass Flare To Female Pipe Gas Cocks are CSA certified and built specially for use with Stationary Appliance Connectors

TECHNICAL DATA SHEET

INSTALLATION DATA SHEET

Features:
• For Indoor/Outdoor applications. C.S.A. Certified forged brass ball valves for Natural and Propane Gas (vapor)
• Brass valves for use in W.O.G. = Water, Oil and Gas 
• Full Port
• Blowout-Proof Stem
• PTFE Seats
• CSA certified to 5 P.S.I. FROM APPLIANCE TO METER

Specifications:
• W.O.G: 600
• Flare Tube Size: 1/2”
• Pipe Size: 1/2” FPT
• Connection Type: Flare Tube to Female
• Materials: Aluminum, Brass, NBR, PTFE, Steel
• Operating temperature: -40°F to +125°F (-40°C to +52°C)
• Weight: 0.26 lbs

Fairview GAS-FLO™ BV5048-8D 1/2" Flare Tube to 1/2” MPT Forged Full Port Brass Ball Valve 600 WOG. Fairview's Brass Flare To Female Pipe Gas Cocks are CSA certified and built specially for use with Stationary Appliance Connectors

TECHNICAL DATA SHEET

INSTALLATION DATA SHEET

Features:
• For Indoor/Outdoor applications. C.S.A. Certified forged brass ball valves for Natural and Propane Gas (vapor)
• Brass valves for use in W.O.G. = Water, Oil and Gas 
• Full Port
• Blowout-Proof Stem
• PTFE Seats
• CSA certified to 5 P.S.I. FROM APPLIANCE TO METER

Specifications:
• W.O.G: 600
• Flare Tube Size: 1/2”
• Pipe Size: 1/2” MPT
• Connection Type: Flare Tube to Male
• Materials: Aluminum, Brass, NBR, PTFE, Steel
• Operating temperature: -40°F to +125°F (-40°C to +52°C)
• Weight: 0.28 lbs

Fairview QD-GMRVC4-4F GAS-FLO™ 1/4” Ball Vale Coupler x 1/4” FPT CSA RV Gas Quick Disconnect. Fairview's Recreational Vehicle Valved Gas QD’s are CSA Certified up to 60 PSI WP

Features:
• C.S.A. (C.G.A. / A.G.A.) design certified for natural gas and L.P. gas - air mixtures
• For quick connect and disconnect of LP gas hose to camper/RV cooking stoves

TECHNICAL DATA SHEET

INSTALLATION INSTRUCTIONS

Specifications:
• Coupler (Body Size): 1/4
• Female Pipe Thread: 1/4
• Material: Brass
• Weight: 4.2 oz

Fairview GAS-FLO™ 1/4” ID x 12” AOL Type 1 Thermoplastic Propane Hose Assembly with 1/4” Male Inverted Flare x POL Fittings. Fairview's Type 1 Thermoplastic POL Pigtails are CSA Certified to 350 PSI WP -40°F To 140°F

Applications:
• Used To Conduct Natural Gas In A Gaseous State And Propane In Either A Liquid Or Gaseous State Up To 350 P.S.I
• UL/CSA Approved Type 1 Propane/Nat Gas Assy (Type 1 Assy)

TECHNICAL DATA SHEET

INSTALLATION INSTRUCTIONS

Specifications:
• Hose ID: 1/4”
• Assembly Overall Length: 12” (Tolerance ± 1/4 of an inch)
• Temperature: -40°F to +140°F
• Color: Black
• Max Pressure: 350 PSI
• End: 1/4” Brass Male Inverted Flare
• End: POL
• TO BE INSTALLED BY LICENSED GAS FITTERS ONLY
• Weight: 0.30 lbs

Fairview GAS-FLO™ 1/4” ID x 12” AOL Type 1 Thermoplastic Propane Hose Assembly with 1/4” Male Inverted Flare x QCC Fittings. Fairview's Type 1 Thermoplastic QCC Pigtails are CSA Certified to 350 PSI WP -40°F To 140°F

Applications:
• Used To Conduct Natural Gas In A Gaseous State And Propane In Either A Liquid Or Gaseous State Up To 350 P.S.I
• UL/CSA Approved Type 1 Propane/Nat Gas Assy (Type 1 Assy)

TECHNICAL DATA SHEET

INSTALLATION INSTRUCTIONS

Specifications:
• Hose ID: 1/4”
• Assembly Overall Length: 12” (Tolerance ± 1/4 of an inch)
• Temperature: -40°F to +140°F
• Color: Black
• Max Pressure: 350 PSI
• End: 1/4” Brass Male Inverted Flare
• End: QCC1 ACME
• TO BE INSTALLED BY LICENSED GAS FITTERS ONLY
• Weight: 0.30 lbs

Fairview GAS-FLO™ 1/4” ID x 120” AOL Type 1 Thermoplastic Propane Hose Assembly with 3/8” 45° SAE Female Swivel Flare x 3/8” 45° SAE Female Swivel Flare Fittings. Fairview's Type 1 Thermoplastic F.SAE Assemblies are CSA Certified to 350 PSI WP -40°F To 140°F

Applications:
• Used To Conduct Natural Gas In A Gaseous State And Propane In Either A Liquid Or Gaseous State Up To 350 P.S.I
• UL/CSA Approved Type 1 Propane/Nat Gas Assy (Type 1 Assy)

TECHNICAL DATA SHEET

Specifications:
• Hose ID: 1/4”
• Assembly Overall Length: 120” (Tolerance ±1% of length measured to the nearest 1/8 of an inch)
• Temperature: -40°F to +140°F
• Color: Black
• Max Pressure: 350 PSI
• End: 3/8” Brass 45° SAE Female Swivel Flare
• End: 3/8” Brass 45° SAE Female Swivel Flare
• TO BE INSTALLED BY LICENSED GAS FITTERS ONLY
• Weight: 0.95 lbs

Fairview GAS-FLO™ 1/4” ID x 120” AOL Type 1 Thermoplastic Propane Hose Assembly with 1”-20 Swivel Male Cylinder Thread x QCC1 Fittings. Fairview's Type 1 Thermoplastic MC X QCC Assemblies are CSA certified to 350 PSI WP -40°F To 140°F

Applications:
• Used To Conduct Natural Gas In A Gaseous State And Propane In Either A Liquid Or Gaseous State Up To 350 P.S.I
• UL/CSA Approved Type 1 Propane/Nat Gas Assy (Type 1 Assy)

TECHNICAL DATA SHEET

Specifications:
• Hose ID: 1/4”
• Assembly Overall Length: 120” (Tolerance ±1% of length measured to the nearest 1/8 of an inch)
• Temperature: -40°F to +140°F
• Hose Color: Black
• Max Pressure: 350 PSI
• End: 1”-20 Swivel Male Cylinder Thread
• End: Black QCC1 ACME
• TO BE INSTALLED BY LICENSED GAS FITTERS ONLY
• Weight: 1.20 lbs

Fairview GAS-FLO™ 1/4” ID x 15” AOL Type 1 Thermoplastic Propane Hose Assembly with 1/4” Male Inverted Flare x QCC Fittings. Fairview's Type 1 Thermoplastic QCC Pigtails are CSA Certified to 350 PSI WP -40°F To 140°F

Applications:
• Used To Conduct Natural Gas In A Gaseous State And Propane In Either A Liquid Or Gaseous State Up To 350 P.S.I
• UL/CSA Approved Type 1 Propane/Nat Gas Assy (Type 1 Assy)

TECHNICAL DATA SHEET

INSTALLATION INSTRUCTIONS

Specifications:
• Hose ID: 1/4”
• Assembly Overall Length: 15” (Tolerance ± 1/4 of an inch)
• Temperature: -40°F to +140°F
• Color: Black
• Max Pressure: 350 PSI
• End: 1/4” Brass Male Inverted Flare
• End: QCC1 ACME
• TO BE INSTALLED BY LICENSED GAS FITTERS ONLY
• Weight: 0.30 lbs

Fairview GAS-FLO™ 1/4” ID x 18” AOL Type 1 Rubber Propane Hose Assembly with 1/4” Male Inverted Flare x POL Fittings. Fairview's Type 1 Rubber POL Pigtails are CSA Certified to 350 PSI WP -60°F To 212°F

Applications:
• Used To Conduct Natural Gas In A Gaseous State And Propane In Either A Liquid Or Gaseous State Up To 350 P.S.I
• UL/CSA Approved Type 1 Propane/Nat Gas Assy (Type 1 Assy)

TECHNICAL DATA SHEET

INSTALLATION INSTRUCTIONS

Specifications:
• Hose ID: 1/4”
• Assembly Overall Length: 18” (Tolerance ± 1/4 of an inch)
• Temperature: -60°F to +212°F
• Color: Black
• Max Pressure: 350 PSI
• End: 1/4” Brass Male Inverted Flare
• End: POL
• TO BE INSTALLED BY LICENSED GAS FITTERS ONLY
• Weight: 0.35 lbs

Fairview GAS-FLO™ 1/4” ID x 36” AOL Type 1 Thermoplastic Propane Hose Assembly with 3/8” 45° SAE Female Swivel Flare x 3/8” 45° SAE Female Swivel Flare Fittings. Fairview's Type 1 Thermoplastic F.SAE Assemblies are CSA Certified to 350 PSI WP -40°F To 140°F

Applications:
• Used To Conduct Natural Gas In A Gaseous State And Propane In Either A Liquid Or Gaseous State Up To 350 P.S.I
• UL/CSA Approved Type 1 Propane/Nat Gas Assy (Type 1 Assy)

TECHNICAL DATA SHEET

Specifications:
• Hose ID: 1/4”
• Assembly Overall Length: 36” (Tolerance ± 1/4 of an inch)
• Temperature: -40°F to +140°F
• Color: Black
• Max Pressure: 350 PSI
• End: 3/8” Brass 45° SAE Female Swivel Flare
• End: 3/8” Brass 45° SAE Female Swivel Flare
• TO BE INSTALLED BY LICENSED GAS FITTERS ONLY
• Weight: 0.40 lbs

Fairview GAS-FLO™ 1/4” ID x 48” AOL Type 1 Thermoplastic Propane Hose Assembly with 1/4” Male Pipe x RV QD Nipple Fittings. Fairview's Type 1 Thermoplastic RVQD Extension Assemblies are CSA Certified to 350 PSI WP -40°F To 140°F

Applications:
• Used To Conduct Natural Gas In A Gaseous State And Propane In Either A Liquid Or Gaseous State Up To 350 P.S.I
• UL/CSA Approved Type 1 Propane/Nat Gas Assy (Type 1 Assy)

TECHNICAL DATA SHEET

INSTALLATION INSTRUCTIONS

Specifications:
• Hose ID: 1/4”
• Assembly Overall Length: 48” (Tolerance ±1% of length measured to the nearest 1/8 of an inch)
• Temperature: -40°F to +140°F
• Color: Black
• Max Pressure: 350 PSI
• End: 1/4” Brass Male Pipe
• End: 1/4” Brass RV QD Nipple
• TO BE INSTALLED BY LICENSED GAS FITTERS ONLY
• Weight: 0.40 lbs

Fairview GAS-FLO™ 1/4” ID x 48” AOL Type 1 Thermoplastic Propane Hose Assembly with RV QD Coupler x QD Nipple Fittings Fairview's Type 1 Thermoplastic RV Outside Appliance Quick Disconnect Hoses are CSA Certified to 350 PSI WP -40°F To 140°F

Applications:
• Used To Conduct Natural Gas In A Gaseous State And Propane In Either A Liquid Or Gaseous State Up To 350 P.S.I
• UL/CSA Approved Type 1 Propane/Nat Gas Assy (Type 1 Assy)

TECHNICAL DATA SHEET

INSTALLATION INSTRUCTIONS

Specifications:
• Hose ID: 1/4”
• Assembly Overall Length: 48” (Tolerance ±1% of length measured to the nearest 1/8 of an inch)
• Temperature: -40°F to +140°F
• Color: Black
• Max Pressure: 350 PSI
• End: 1/4” Brass RV QD Coupler
• End: 1/4” Brass RV QD Nipple
• TO BE INSTALLED BY LICENSED GAS FITTERS ONLY
• Weight: 0.60 lbs