Fairview USA Inc.

Fairview SRT125-4B 1/4 ID x 1/4 Male Pipe Steel Reusable Hose End s for use with S.A.E. 100R1-AT (NON-SKIVE) hose

TECHNICAL DATA SHEET

INSTALLATION DATA SHEET

Specifications:
• Steel Reusable Hose Ends for use with S.A.E. 100R1-AT (NON-SKIVE) hose
• Medium to high pressure service in the handling of most hydraulic fluids, gasoline, diesel fuels, lubricating oils and water
• Working Temperature: -40°F to +250°F, -40°C to +121°C
• Working Pressure: Are hose size dependent

Accutek® QD-ISOAC16-16F 1 Coupler x 1 Female Pipe ISO Series A 7241-1 Steel 3,000 PSI Quick Disconnect. Fairview's ISO A Interchange Couplers Interchange with Aeroquip 5600, Parker 6600, Safeway S56 and Faster ANV Series

Features:
• Industry interchangeability with other manufacturer's ISO "A" couplers and nipples
• High Strength Steel Construction
• Nitrile NBR seals with PTFE back-up ring
• Proven ball lock mechanism
• 4 : 1 safety factor (Min. Burst = WP. X 4)
• Hydraulic applications where connection and disconnection is required either for maintenance or operation
• For use on truck & trailer, snow plows, agricultural, dump, construction equipment

Specifications:
• Working Pressure: 3,000 PSI
• Body Size: 1
• Female Pipe: 1
• Body Material: Steel
• Temperature Range: -40F to 250F
• Approx. Weight: 1.65 lbs

Fairview SRT125-6C 3/8 ID x 3/8 Male Pipe Steel Reusable Hose End s for use with S.A.E. 100R1-AT (NON-SKIVE) hose

TECHNICAL DATA SHEET

INSTALLATION DATA SHEET

Specifications:
• Steel Reusable Hose Ends for use with S.A.E. 100R1-AT (NON-SKIVE) hose
• Medium to high pressure service in the handling of most hydraulic fluids, gasoline, diesel fuels, lubricating oils and water
• Working Temperature: -40°F to +250°F, -40°C to +121°C
• Working Pressure: Are hose size dependent

Fairview GAS-FLO® GR-9950 Low Pressure LP Gas Two Stage Regulator 1/4 FPT In x 3/8 FPT Out 225,000 BTU/HR. Fairview's GAS-FLO® Two Stage LP Gas Regulators are ideal for use on RV's and commercial size grill

Features:
• The X-SERIES* model GR-9950 and GR-9959 regulator combines both a high pressure first stage and a low pressure second stage regulator into a single unit
• Ideally designed for RV applications, these regulators ensure a smooth and continuous flow of gas to all appliances
• Excess Flow
• Zinc Die Cast
• Molded Rubber Diaphragms
• CSA Listed to U.L. 144
• 2nd Stage Relief Mechanism Per U.L. 144
• Adjusting Screw and Dust Cap Design
• Powder Coated

TECHNICAL DATA SHEET

INSTALLATION DATA SHEET

Specifications:
• Inlet: 1/4 FPT
• Outlet: 3/8 FPT
• Vent position: Above Outlet
• Capacity BTU/Hr Propane: 225,000
• TO BE INSTALLED BY LICENSED GAS FITTERS ONLY
• Weight: 1.25 lbs

Fairview FLEX-DOT 1485 Series 1/4" x 100' Red Non-Reinforced Air Brake Tubing - Type 3A. Air brake tube is designed for use with truck, trailer and other mobile air brake and auxiliary systems. This lightweight, flexible and UV stabilized tube is highly resistant to abrasion, oil, grease and road salt

MEETS OR EXCEEDS: D.O.T. F.M.V.S.S. 106 S.A.E. J844 TEST REQUIREMENTS

FLEX-DOT 1485 Series Air Brake Tube is MADE IN CANADA

Compliance:
• All series 1485 tube are designed in compliance with the revised DOT 106 standard which took effect December 24th, 2007
• Fairview’s FLEX-DOT air brake tube is dimensionally identical to the previous air brake tube described in SAE J844 Type A and Type B, and is compatible with the same fittings. Both compression and push-to-connect fittings can be used with FLEX-DOT tube in all applications other than truck to trailer connections, in which push-to-connect fittings are not suitable

Materials:
• Both the core tube and jacket are comprised of a custom formulated elastomer, offering exceptional heat aging, oil resistance, and low temperature flexibility, when compared to previous nylon materials
• With its improved flexibility at all temperatures, the FLEX-DOT tube is easier to install in tight quarters
• The special compound was custom formulated for this application and offers exceptional flexibility even at very low temperatures. Unlike traditional all-nylon tube, the FLEX-DOT elastomer hose can still be flexed at -65C (-85F)

SPECIFICATION SHEET FLEX-DOT SERIES 1485

INSTALLATION DATA SHEET

Specifications:
• Nominal OD: 1/4”
• Inside Diameter ID: 0.170”
• Wall Thickness: 0.040" +/-0.003"
• Length: 100’
• Temperature: -85°F to +200°F, -65°C to +93°C
• Type: 3A, Non-Reinforced
• Color: Red
• Working Pressure: 300 PSI
• Minimum Burst @ 68°F: 1,200 PSI
• Supported Bend Radius: 1.00”
• Unsupported Bend Radius: 1.00”
• Approx. Weight: 1.45 lbs

Fairview GAS-FLO® GR-330 High Pressure Pounds-To-Pounds LP Gas Regulator 1/4 FPT 1,500,000 BTU/HR. Fairview's GAS-FLO® Lbs to Lbs adjustable LP-Gas Regulators are ideal for LP torches and other high flow applications

Applications:
• Designed for cylinder systems in liquid or vapor service
• Delivery pressures are adjustable from 0-30 PSI
• Ideally suited for a variety of industrial applications
• Torches • Construction Heaters • Fish Cookers • Tar Pot Heaters • Flame Cultivators
• UL Listed

TECHNICAL DATA SHEET

Specifications:
• Inlet: 1/4 FPT
• Outlet: 1/4 FPT
• Delivery Pressure Range: 0-30 PSIG
• Outlet Pressure (Set Point): 30 PSIG
• Maximum Inlet Pressure: 250 PSIG
• Capacity BTU/Hr Propane: 1,500,000
• Gauge Port: 1/4 FPT (Plugged)
• TO BE INSTALLED BY LICENSED GAS FITTERS ONLY
• Weight: 1.30 lbs

Fairview GAS-FLO® GR-360 High Pressure Pounds-To-Pounds LP Gas Regulator 1/4 FPT 2,000,000 BTU/HR 0-60 PSIG Range. Fairview's GAS-FLO® Lbs to Lbs adjustable LP-Gas Regulators are ideal for LP torches and other high flow applications

Applications:
• Designed for cylinder systems in liquid or vapor service
• Delivery pressures are adjustable from 0-60 PSI
• Ideally suited for a variety of industrial applications
• Torches • Construction Heaters • Fish Cookers • Tar Pot Heaters • Flame Cultivators
• UL Listed

TECHNICAL DATA SHEET

Specifications:
• Inlet: 1/4 FPT
• Outlet: 1/4 FPT
• Delivery Pressure Range: 0-60 PSIG
• Outlet Pressure (Set Point): 60 PSIG
• Maximum Inlet Pressure: 250 PSIG
• Capacity BTU/Hr Propane: 2,000,000
• Gauge Port: 1/4 FPT (Plugged)
• TO BE INSTALLED BY LICENSED GAS FITTERS ONLY
• Weight: 1.30 lbs

Fairview WR-RV55 Lead-Free RV Water Pressure Regulator 55 PSI. Fairview's Lead-Free R.V. Water Pressure Regulator offers the highest water flow available while maintaining 55 PSI WP Max

Features:
• Lead-Free design
• Keeps outlet pressure at 55 PSI
• Highest water flow available
• Screened washer filters debris
• Fits all standard water hose and riser connections
• Heavy-Duty impact resistant design

Specifications:
• Connections: FWH X MWH
• Weight: 8.2 oz

Fairview GAS-FLO® GR-9959 Low Pressure LP Gas Two Stage Regulator 1/4 FPT In x 3/8 FPT Out 9:00 Vent 225,000 BTU/HR. Fairview's GAS-FLO® Two Stage LP Gas Regulators are ideal for use on RV's and commercial size grill

Features:
• The X-SERIES* model GR-9950 and GR-9959 regulator combines both a high pressure first stage and a low pressure second stage regulator into a single unit
• Ideally designed for RV applications, these regulators ensure a smooth and continuous flow of gas to all appliances
• Excess Flow
• Zinc Die Cast
• Molded Rubber Diaphragms
• CSA Listed to U.L. 144
• 2nd Stage Relief Mechanism Per U.L. 144
• Adjusting Screw and Dust Cap Design
• Powder Coated

TECHNICAL DATA SHEET

INSTALLATION DATA SHEET

Specifications:
• Inlet: 1/4 FPT
• Outlet: 3/8 FPT
• Vent position: 9:00 / 90°
• Capacity BTU/Hr Propane: 225,000
• TO BE INSTALLED BY LICENSED GAS FITTERS ONLY
• Weight: 1.25 lbs

Fairview FLEX-DOT 1485 Series 1/8" x 100' Black Non-Reinforced Air Brake Tubing - Type 3A. Air brake tube is designed for use with truck, trailer and other mobile air brake and auxiliary systems. This lightweight, flexible and UV stabilized tube is highly resistant to abrasion, oil, grease and road salt

MEETS OR EXCEEDS: S.A.E. J844 TEST REQUIREMENTS

FLEX-DOT 1485 Series Air Brake Tube is MADE IN CANADA

Compliance:
• Fairview’s FLEX-DOT air brake tube is dimensionally identical to the previous air brake tube described in SAE J844 Type A and Type B, and is compatible with the same fittings. Both compression and push-to-connect fittings can be used with FLEX-DOT tube in all applications other than truck to trailer connections, in which push-to-connect fittings are not suitable

Materials:
• Both the core tube and jacket are comprised of a custom formulated elastomer, offering exceptional heat aging, oil resistance, and low temperature flexibility, when compared to previous nylon materials
• With its improved flexibility at all temperatures, the FLEX-DOT tube is easier to install in tight quarters
• The special compound was custom formulated for this application and offers exceptional flexibility even at very low temperatures. Unlike traditional all-nylon tube, the FLEX-DOT elastomer hose can still be flexed at -65C (-85F)

SPECIFICATION SHEET FLEX-DOT SERIES 1485

INSTALLATION DATA SHEET

Specifications:
• Nominal OD: 1/8”
• Inside Diameter ID: 0.079”
• Wall Thickness: 0.023" +/-0.003"
• Length: 100’
• Temperature: -85°F to +200°F, -65°C to +93°C
• Type: 3A, Non-Reinforced
• Color: Black
• Working Pressure: 250 PSI
• Minimum Burst @ 68°F: 1,000 PSI
• Supported Bend Radius: 0.37”
• Unsupported Bend Radius: 0.37”
• Approx. Weight: 0.44 lbs

Fairview FLEX-DOT 1485 Series 1/8" x 100' Blue Non-Reinforced Air Brake Tubing - Type 3A. Air brake tube is designed for use with truck, trailer and other mobile air brake and auxiliary systems. This lightweight, flexible and UV stabilized tube is highly resistant to abrasion, oil, grease and road salt

MEETS OR EXCEEDS: S.A.E. J844 TEST REQUIREMENTS

FLEX-DOT 1485 Series Air Brake Tube is MADE IN CANADA

Compliance:
• Fairview’s FLEX-DOT air brake tube is dimensionally identical to the previous air brake tube described in SAE J844 Type A and Type B, and is compatible with the same fittings. Both compression and push-to-connect fittings can be used with FLEX-DOT tube in all applications other than truck to trailer connections, in which push-to-connect fittings are not suitable

Materials:
• Both the core tube and jacket are comprised of a custom formulated elastomer, offering exceptional heat aging, oil resistance, and low temperature flexibility, when compared to previous nylon materials
• With its improved flexibility at all temperatures, the FLEX-DOT tube is easier to install in tight quarters
• The special compound was custom formulated for this application and offers exceptional flexibility even at very low temperatures. Unlike traditional all-nylon tube, the FLEX-DOT elastomer hose can still be flexed at -65C (-85F)

SPECIFICATION SHEET FLEX-DOT SERIES 1485

INSTALLATION DATA SHEET

Specifications:
• Nominal OD: 1/8”
• Inside Diameter ID: 0.079”
• Wall Thickness: 0.023" +/-0.003"
• Length: 100’
• Temperature: -85°F to +200°F, -65°C to +93°C
• Type: 3A, Non-Reinforced
• Color: Blue
• Working Pressure: 250 PSI
• Minimum Burst @ 68°F: 1,000 PSI
• Supported Bend Radius: 0.37”
• Unsupported Bend Radius: 0.37”
• Approx. Weight: 0.44 lbs

Fairview FLEX-DOT 1485 Series 1/8" x 100' Red Non-Reinforced Air Brake Tubing - Type 3A. Air brake tube is designed for use with truck, trailer and other mobile air brake and auxiliary systems. This lightweight, flexible and UV stabilized tube is highly resistant to abrasion, oil, grease and road salt

MEETS OR EXCEEDS: S.A.E. J844 TEST REQUIREMENTS

FLEX-DOT 1485 Series Air Brake Tube is MADE IN CANADA

Compliance:
• Fairview’s FLEX-DOT air brake tube is dimensionally identical to the previous air brake tube described in SAE J844 Type A and Type B, and is compatible with the same fittings. Both compression and push-to-connect fittings can be used with FLEX-DOT tube in all applications other than truck to trailer connections, in which push-to-connect fittings are not suitable

Materials:
• Both the core tube and jacket are comprised of a custom formulated elastomer, offering exceptional heat aging, oil resistance, and low temperature flexibility, when compared to previous nylon materials
• With its improved flexibility at all temperatures, the FLEX-DOT tube is easier to install in tight quarters
• The special compound was custom formulated for this application and offers exceptional flexibility even at very low temperatures. Unlike traditional all-nylon tube, the FLEX-DOT elastomer hose can still be flexed at -65C (-85F)

SPECIFICATION SHEET FLEX-DOT SERIES 1485

INSTALLATION DATA SHEET

Specifications:
• Nominal OD: 1/8”
• Inside Diameter ID: 0.079”
• Wall Thickness: 0.023" +/-0.003"
• Length: 100’
• Temperature: -85°F to +200°F, -65°C to +93°C
• Type: 3A, Non-Reinforced
• Color: Red
• Working Pressure: 250 PSI
• Minimum Burst @ 68°F: 1,000 PSI
• Supported Bend Radius: 0.37”
• Unsupported Bend Radius: 0.37”
• Approx. Weight: 0.44 lbs

Fairview FLEX-DOT 1485 Series 1/8" x 100' Green Non-Reinforced Air Brake Tubing - Type 3A. Air brake tube is designed for use with truck, trailer and other mobile air brake and auxiliary systems. This lightweight, flexible and UV stabilized tube is highly resistant to abrasion, oil, grease and road salt

MEETS OR EXCEEDS: S.A.E. J844 TEST REQUIREMENTS

FLEX-DOT 1485 Series Air Brake Tube is MADE IN CANADA

Compliance:
• Fairview’s FLEX-DOT air brake tube is dimensionally identical to the previous air brake tube described in SAE J844 Type A and Type B, and is compatible with the same fittings. Both compression and push-to-connect fittings can be used with FLEX-DOT tube in all applications other than truck to trailer connections, in which push-to-connect fittings are not suitable

Materials:
• Both the core tube and jacket are comprised of a custom formulated elastomer, offering exceptional heat aging, oil resistance, and low temperature flexibility, when compared to previous nylon materials
• With its improved flexibility at all temperatures, the FLEX-DOT tube is easier to install in tight quarters
• The special compound was custom formulated for this application and offers exceptional flexibility even at very low temperatures. Unlike traditional all-nylon tube, the FLEX-DOT elastomer hose can still be flexed at -65C (-85F)

SPECIFICATION SHEET FLEX-DOT SERIES 1485

INSTALLATION DATA SHEET

Specifications:
• Nominal OD: 1/8”
• Inside Diameter ID: 0.079”
• Wall Thickness: 0.023" +/-0.003"
• Length: 100’
• Temperature: -85°F to +200°F, -65°C to +93°C
• Type: 3A, Non-Reinforced
• Color: Green
• Working Pressure: 250 PSI
• Minimum Burst @ 68°F: 1,000 PSI
• Supported Bend Radius: 0.37”
• Unsupported Bend Radius: 0.37”
• Approx. Weight: 0.44 lbs

Fairview PC1464-12 3/4 Tube OD x 3/4 Tube OD x 3/4 Tube OD Brass D.O.T. Push-To-Connect Union Tee Air Brake Fitting. Fairview's Union Tees Feature A Labor Saving Full Flow Design That Requires No Tools

Applications:
• Air brake systems. Used with copper tubing for rigid plumbing along frame and air tank
• Use with J844D Nylon Air Brake Tube
• D.O.T. RECOGNIZED FOR ALL AIR BRAKE APPLICATIONS EXCEPT THOSE FOR USE BETWEEN FRAME AND AXLE OR BETWEEN TOWED AND TOWING VEHICLES

TECHNICAL DATA SHEET

INSTALLATION DATA SHEET

Specifications:
• Fitting Type: Push-To-Connect
• Fitting Style: Union Tee
• Tube OD: 3/4"
• Material: Brass
• Working Temperature: -40°F (-40°C) to 225°F (107°C)
• Weight 0.34 lbs

Accutek® QD-BISOBC8-8F 1/2 Coupler x 1/2 Female Pipe ISO Series B 7241-1 Brass 3,500 PSI Quick Disconnect. Fairview's ISO B Interchange Couplers Interchange with Aeroquip FD45, Foster FHK, Parker 60, Safeway BS10 and Faster HNV Series

Features:
• High flow characteristics and pressure ratings superior to Parker 60 series
• Industry interchangeability with other manufacturer's ISO "B" couplers and nipples
• Poppet style double shut-off.
• Nitrile NBR seals with PTFE back-up ring
• Proven ball lock mechanism
• 4 : 1 safety factor (Min. Burst = WP. X 4)
• Ideal for use with hydraulic and other fluids in both stationary and mobile industrial applications

Specifications:
• Working Pressure: 3,500 PSI
• Body Size: 1/2
• Female Pipe: 1/2
• Body Material: Brass
• Approx. Weight: 0.75 lbs

Fairview GAS-FLO® GR-9288C Compact Low Pressure LP Gas Second Stage Regulator 1/2 F NPT In x 1/2 F NPT Out 1,200,000 BTU/HR. Fairview's Compact Low Pressure Lp Gas Second Stage Regulators provide the highest gas flows available in a compact design

Features:
• Second Stage regulators are designed to reduce the pressure from a First-Stage regulator
• Its’ compact design makes it the ideal choice for small domestic applications
• These adjustable regulators are factory set at 11" w.c. with first stage inlet pressure of 10 psig
• Equipped with integral relief valve and built-in 1/8" FNPT gauge tap
• UL Listed

TECHNICAL DATA SHEET

INSTALLATION DATA SHEET

Specifications:
• Inlet: 1/2 F NPT
• Outlet: 1/2 F NPT
• Delivery Pressure: 11" W.C. @ 10 PSI
• Vent Position: Over Inlet
• Capacity BTU/Hr Propane: 1,200,000
• Mount: Standard
• TO BE INSTALLED BY LICENSED GAS FITTERS ONLY
• Weight: 1.60 lbs

Fairview GAS-FLO® GR-92812C Compact Low Pressure LP Gas Second Stage Regulator 1/2 F NPT In x 3/4 F NPT Out 1,200,000 BTU/HR. Fairview's Compact Low Pressure Lp Gas Second Stage Regulators provide the highest gas flows available in a compact design

Features:
• Second Stage regulators are designed to reduce the pressure from a First-Stage regulator
• Its’ compact design makes it the ideal choice for small domestic applications
• These adjustable regulators are factory set at 11" w.c. with first stage inlet pressure of 10 psig
• Equipped with integral relief valve and built-in 1/8" FNPT gauge tap
• UL Listed

TECHNICAL DATA SHEET

INSTALLATION DATA SHEET

Specifications:
• Inlet: 1/2 F NPT
• Outlet: 3/4 F NPT
• Delivery Pressure: 11" W.C. @ 10 PSI
• Vent Position: Over Inlet
• Capacity BTU/Hr Propane: 1,200,000
• Mount: Standard
• TO BE INSTALLED BY LICENSED GAS FITTERS ONLY
• Weight: 1.60 lbs

Fairview FLEX-DOT 1485 Series 1/4" x 100' Blue Non-Reinforced Air Brake Tubing - Type 3A. Air brake tube is designed for use with truck, trailer and other mobile air brake and auxiliary systems. This lightweight, flexible and UV stabilized tube is highly resistant to abrasion, oil, grease and road salt

MEETS OR EXCEEDS: D.O.T. F.M.V.S.S. 106 S.A.E. J844 TEST REQUIREMENTS

FLEX-DOT 1485 Series Air Brake Tube is MADE IN CANADA

Compliance:
• All series 1485 tube are designed in compliance with the revised DOT 106 standard which took effect December 24th, 2007
• Fairview’s FLEX-DOT air brake tube is dimensionally identical to the previous air brake tube described in SAE J844 Type A and Type B, and is compatible with the same fittings. Both compression and push-to-connect fittings can be used with FLEX-DOT tube in all applications other than truck to trailer connections, in which push-to-connect fittings are not suitable

Materials:
• Both the core tube and jacket are comprised of a custom formulated elastomer, offering exceptional heat aging, oil resistance, and low temperature flexibility, when compared to previous nylon materials
• With its improved flexibility at all temperatures, the FLEX-DOT tube is easier to install in tight quarters
• The special compound was custom formulated for this application and offers exceptional flexibility even at very low temperatures. Unlike traditional all-nylon tube, the FLEX-DOT elastomer hose can still be flexed at -65C (-85F)

SPECIFICATION SHEET FLEX-DOT SERIES 1485

INSTALLATION DATA SHEET

Specifications:
• Nominal OD: 1/4”
• Inside Diameter ID: 0.170”
• Wall Thickness: 0.040" +/-0.003"
• Length: 100’
• Temperature: -85°F to +200°F, -65°C to +93°C
• Type: 3A, Non-Reinforced
• Color: Blue
• Working Pressure: 300 PSI
• Minimum Burst @ 68°F: 1,200 PSI
• Supported Bend Radius: 1.00”
• Unsupported Bend Radius: 1.00”
• Approx. Weight: 1.45 lbs

Fairview FLEX-DOT 1485 Series 1/4" x 100' Green Non-Reinforced Air Brake Tubing - Type 3A. Air brake tube is designed for use with truck, trailer and other mobile air brake and auxiliary systems. This lightweight, flexible and UV stabilized tube is highly resistant to abrasion, oil, grease and road salt

MEETS OR EXCEEDS: D.O.T. F.M.V.S.S. 106 S.A.E. J844 TEST REQUIREMENTS

FLEX-DOT 1485 Series Air Brake Tube is MADE IN CANADA

Compliance:
• All series 1485 tube are designed in compliance with the revised DOT 106 standard which took effect December 24th, 2007
• Fairview’s FLEX-DOT air brake tube is dimensionally identical to the previous air brake tube described in SAE J844 Type A and Type B, and is compatible with the same fittings. Both compression and push-to-connect fittings can be used with FLEX-DOT tube in all applications other than truck to trailer connections, in which push-to-connect fittings are not suitable

Materials:
• Both the core tube and jacket are comprised of a custom formulated elastomer, offering exceptional heat aging, oil resistance, and low temperature flexibility, when compared to previous nylon materials
• With its improved flexibility at all temperatures, the FLEX-DOT tube is easier to install in tight quarters
• The special compound was custom formulated for this application and offers exceptional flexibility even at very low temperatures. Unlike traditional all-nylon tube, the FLEX-DOT elastomer hose can still be flexed at -65C (-85F)

SPECIFICATION SHEET FLEX-DOT SERIES 1485

INSTALLATION DATA SHEET

Specifications:
• Nominal OD: 1/4”
• Inside Diameter ID: 0.170”
• Wall Thickness: 0.040" +/-0.003"
• Length: 100’
• Temperature: -85°F to +200°F, -65°C to +93°C
• Type: 3A, Non-Reinforced
• Color: Green
• Working Pressure: 300 PSI
• Minimum Burst @ 68°F: 1,200 PSI
• Supported Bend Radius: 1.00”
• Unsupported Bend Radius: 1.00”
• Approx. Weight: 1.45 lbs

Fairview FLEX-DOT 1485 Series 1/4" x 100' Orange Non-Reinforced Air Brake Tubing - Type 3A. Air brake tube is designed for use with truck, trailer and other mobile air brake and auxiliary systems. This lightweight, flexible and UV stabilized tube is highly resistant to abrasion, oil, grease and road salt

MEETS OR EXCEEDS: D.O.T. F.M.V.S.S. 106 S.A.E. J844 TEST REQUIREMENTS

FLEX-DOT 1485 Series Air Brake Tube is MADE IN CANADA

Compliance:
• All series 1485 tube are designed in compliance with the revised DOT 106 standard which took effect December 24th, 2007
• Fairview’s FLEX-DOT air brake tube is dimensionally identical to the previous air brake tube described in SAE J844 Type A and Type B, and is compatible with the same fittings. Both compression and push-to-connect fittings can be used with FLEX-DOT tube in all applications other than truck to trailer connections, in which push-to-connect fittings are not suitable

Materials:
• Both the core tube and jacket are comprised of a custom formulated elastomer, offering exceptional heat aging, oil resistance, and low temperature flexibility, when compared to previous nylon materials
• With its improved flexibility at all temperatures, the FLEX-DOT tube is easier to install in tight quarters
• The special compound was custom formulated for this application and offers exceptional flexibility even at very low temperatures. Unlike traditional all-nylon tube, the FLEX-DOT elastomer hose can still be flexed at -65C (-85F)

SPECIFICATION SHEET FLEX-DOT SERIES 1485

INSTALLATION DATA SHEET

Specifications:
• Nominal OD: 1/4”
• Inside Diameter ID: 0.170”
• Wall Thickness: 0.040" +/-0.003"
• Length: 100’
• Temperature: -85°F to +200°F, -65°C to +93°C
• Type: 3A, Non-Reinforced
• Color: Orange
• Working Pressure: 300 PSI
• Minimum Burst @ 68°F: 1,200 PSI
• Supported Bend Radius: 1.00”
• Unsupported Bend Radius: 1.00”
• Approx. Weight: 1.45 lbs