Delavan Fluid Power

Delavan 50-126 Aluminum Heat Sink. Fits all 4" Diameter Delavan motors

Specifications:
• Snap-fit heat sinks will reduce motor heat up to 30%
• Works with Delavan 7870, 7970, 7871, 7971, FB2 & FB3 series pumps
• Help to extend the available run time of the pump as well as increase motor life
• Heat sinks are made of extruded aluminum with a clear finish
• Overall Dimensions: 3.75” L x 5.0” W x 3.44” H
• Replaces 50-125
• Net Weight: 0.50 Lbs.

• Delavan Nylon 3/4" QA X 3/4" HB Elbow Fitting w/ O-Ring
• Works with 5900, 7822FS and FB2 7900 Series Quick Attach Pumps

• Delavan Nylon 3/4" QA X 3/4" HB Straight Fitting w/ O-Ring
• Works with 5900, 7822FS and FB2 7900 Series Quick Attach Pumps

• Delavan Nylon 3/4" QA X 3/8" HB Elbow Fitting w/ O-Ring
• Works with 5900, 7822FS and FB2 7900 Series Quick Attach Pumps

Delavan PML40-125 Hydraulic Cylinder Repair Kit

Kit Includes:
• Wiper Seal: 1
• Rod Seal: 1
• Piston Seal: 1
• Grand O-Rings: 2
• Piston Rod O-Ring: 1

PML SERIES Tie-Rod Cylinders Seal Location and Descriptions

Specifications:
• Bore Size: 4”
• Rod Size: 1-1/4”
• Weight: 0.90 Oz

Note: Only works with cylinders having serial number starting with a XH (located near base of cylinder imprinted on the tube)

Delavan Closed Center Plug for MBV Valves

• Delavan Nylon 3/4" QA X 1/2" HB Elbow Fitting w/ O-Ring
• Works with 5900, 7822FS and FB2 7900 Series Quick Attach Pumps

• Delavan Upper Housing Assembly
• Works with Delavan 7801 & 7802 series pumps with pressure switch
• Inlet/Outlet Ports - 5/8 quick attach
• Includes pumps head housing and pressure switch part
• Note: Does not work with I-Series pumps

Delavan PowerFLO™ 7812 Series 2.0 GPM 60 PSI Diaphragm Pump with 3/8” FNPT Ports. Demand Switch – Operates only when liquid flow is required

Features:
• Certified to NSF/ANSI Standard 61 & 372
• Made in the USA
• 100% Factory tested
• 2 Year warranty from date of purchase

Motor:
• Type: 12 VDC permanent magnet, totally enclosed, non-ventilated
• Leads: 14 AWG, 6” long with 2-pin connector
• Max Amps: 8.5
• Duty Cycle: See Heat Rise graph

Materials of Construction:
• Motor Shell: Coated Steel
• Housing: Polypropylene
• Valves: Viton
• Diaphragm: Santoprene
• Fasteners: Stainless Steel

NSF/ANSI Certified:
• NSF/ANSI Standard 61 - Drinking Water System Components - Health Effects
• NSF/ANSI 372 and conforms with the lead content requirements for “lead free” plumbing as defined by California, Vermont, Maryland, and Louisiana state laws and the U.S. Safe Drinking Water Act

Pump:
• Demand Switch – Operates only when liquid flow is required
• Type: 3-chamber positive displacement
• Capable of being run dry
• Excellent self-priming capability
• Liquid Temperature: 140°F Max.
• Priming Capabilities: 14’
• Max. Flow: 2.0 GPM
• Pressure Shut-Off: 60 PSI
• Inlet/Outlet Ports: 3/8” FNPT
• Packaging: Small box
• Weight: 5.6 lbs

Delavan PowerFLO™ 7802 Series 2.0 GPM 60 PSI Diaphragm Pump with 5/8” Quick Attach Ports. Demand Switch – Operates only when liquid flow is required

Features:
• Certified to NSF/ANSI Standard 61 & 372
• Made in the USA
• 100% Factory tested
• 2 Year warranty from date of purchase

Motor:
• Type: 12 VDC permanent magnet, totally enclosed, non-ventilated
• Leads: 14 AWG, 6” long with 2-pin connector
• Max Amps: 8.5
• Duty Cycle: See Heat Rise graph

Materials of Construction:
• Motor Shell: Coated Steel
• Housing: Polypropylene
• Valves: Viton
• Diaphragm: Santoprene
• Fasteners: Stainless Steel

NSF/ANSI Certified:
• NSF/ANSI Standard 61 - Drinking Water System Components - Health Effects
• NSF/ANSI 372 and conforms with the lead content requirements for “lead free” plumbing as defined by California, Vermont, Maryland, and Louisiana state laws and the U.S. Safe Drinking Water Act

Pump:
• Demand Switch – Operates only when liquid flow is required
• Type: 3-chamber positive displacement
• Capable of being run dry
• Excellent self-priming capability
• Liquid Temperature: 140°F Max.
• Priming Capabilities: 14’
• Max. Flow: 2.0 GPM
• Pressure Shut-Off: 60 PSI
• Inlet/Outlet Ports: 5/8 Quick Attach
• Packaging: Small box
• Weight: 5.6 lbs

Delavan PowerFLO™ 2200 Series Diaphragm Pump. Demand Switch – Operates only when liquid flow is required

Motor:
• Type: 12 VDC, permanent magnet, thermally protected, splash proof
• Leads: 18 AWG, 4.5” long with 2-pin connector
• Amps: 3.5 Max.
• Duty Cycle: Intermittent

Materials of Construction:
• Motor Housing: Nylon 6/6
• Pump Housing: Polypropylene
• Valves: Viton
• Diaphragm: Santoprene

Pump:
• Demand Switch – Operates only when liquid flow is required
• Shut-Off: 40 ±5 PSI factory setting
• Turn-On: 25 ±5 PSI factory setting
• Type: 2-chamber positive displacement
• Capable of being run dry
• Excellent self-priming capability
• Liquid Temperature: 110°F Max.
• Priming Capabilities: 4 feet suction lift
• Max. Flow: 1.0 GPM
• Max Pressure: 40 PSI
• Inlet/Outlet Ports: 3/8” hose barb
• Packaging: Small box
• UPC: 830344009724 & 830344007591
• Weight: 1.25 lbs

Delavan PowerFLO™ 5850 Series 5.0 GPM 60 PSI Diaphragm Pump. Demand Switch – Operates only when liquid flow is required.

Features:
• Certified to NSF/ANSI Standard 61 & 372
• Made in the USA
• 100% Factory tested
• 2 Year warranty from date of purchase

Motor:
• Type: 12 VDC permanent magnet, totally enclosed, non-ventilated
• Leads: 14 AWG, 6” long with 2-pin connector
• Amps: 6.0 – 16.3
• Duty Cycle: See Heat Rise graph

Materials of Construction:
• Motor Shell: Coated Steel
• Housing: Polypropylene
• Valves: Viton
• Diaphragm: Santoprene
• Fasteners: Stainless Steel

NSF/ANSI Certified:
• NSF/ANSI Standard 61 - Drinking Water System Components - Health Effects
• NSF/ANSI 372 and conforms with the lead content requirements for “lead free” plumbing as defined by California, Vermont, Maryland, and Louisiana state laws and the U.S. Safe Drinking Water Act

Pump:
• Demand Switch – Operates only when liquid flow is required
• Type: 5-chamber positive displacement
• Capable of being run dry
• Excellent self-priming capability
• Liquid Temperature: 140° F Max.
• Priming Capabilities: 14’
• Max. Flow: 5.0 GPM
• Pressure Shut-Off: 60 PSI
• Inlet/Outlet Ports: 1/2” FNPT
• Replaces 5850-101E
• Packaging: Small box
• Weight: 6.0 lbs

Delavan PowerFLO™ 7822FS Flex I-Series 2.2 GPM 60 PSI Diaphragm Pump with 3/4” Quick Attach Ports and Fittings Kit. Thanks to the new 3/4” Quick Attach adapter system and bolt pattern, the Flex Pump can fit into most competitor spray systems that use 3/4” quick attach with ease. The new Flex I-Series Pump will be able to replace your old pump and provide a new level of performance and life. You can figuratively speaking “feel the difference in weight and productivity” between the two pumps.

Features:
• 100% Factory tested
• 2 Year warranty from date of purchase
• This demand pump will turn off when the spray gun or boom is turned off, saving energy and increasing the life of the pump

Motor:
• Type: 12 VDC permanent magnet, totally enclosed, non-ventilated
• Leads: 14 AWG, 6” long with 2-pin connector
• Max Amps: 8.5
• Duty Cycle: See Heat Rise graph

Materials of Construction:
• Motor Shell: Coated Steel
• Housing: Polypropylene
• Valves: Santoprene
• Diaphragm: Santoprene
• Fasteners: Stainless Steel

Quick Connect Fittings Kit:
• (2) 5/8” QA x 3/8" HB Elbow Fittings
• (1) 5/8” QA x 3/8" Straight HB Fitting
• (2) 3/4” to 5/8” Port Adapter
• (2) Slide Connectors for 5/8” Fittings

Pump:
• Demand Switch – Operates only when liquid flow is required
• Type: 3-chamber positive displacement
• Capable of being run dry
• Excellent self-priming capability
• Liquid Temperature: 140°F Max.
• Priming Capabilities: 14’
• Max. Flow: 2.2 GPM
• Pressure Shut-Off: 60 PSI
• Inlet/Outlet Ports: 3/4 Quick Attach
• Replaces 7822FS-201-I, 7822FS-201-BBI
• Packaging: Small box
• Weight: 6.0 lbs

Quick Connect Fittings Kit for Delavan 2.2 GPM Flex Pump:

• (2) 5/8” QA x 3/8" HB Elbow Fittings
• (1) 5/8” QA x 3/8" Straight HB Fitting
• (2) 3/4” to 5/8” Port Adapter
• (2) Slide Connectors for 5/8” Fittings

• Delavan Complete Pump Head Assembly
• Works with Delavan 7870 FB2 series pumps with bypass
• Threaded head with 1/2" FNPT Ports

Delavan PowerMAX™ Stroke Control Kit 2 Fits 1-3/4" to 2" Cylinder Shafts

10 Micron Delavan Model ESP-034-P10 Universal Hydraulic Oil Filter. Universal hydraulic system return line filter for log splitters, small tractors and other power equipment

Features:
• 2.5x finer than standard filters
• High efficiency – High capacity
• Traps dirt and contaminants, #1 killer of hydraulic systems

Specifications:
• 10 Micron nominal particulate filtration
• Maximum pressure 170 PSI
• Meets SAE std of USA
• Dimension 3.75” x 5”
• Weight: 1.3 lbs

Delavan HYDRES-5 PowerMAX™ 5 Gallon Steel Hydraulic Reservoir Tank with Inlet 1-1/2" FNPT and Outlet 3/4" FNPT. Constructed of sturdy 14 gauge steel and black powder coated for protection and durability

Features:
• 14 Gauge steel construction with black powder coated finish
• Breather cap
• Inlet strainer

Specifications:
• Tank Capacity: 5 Gal
• Inlet Port Size: 1-1/2”
• Outlet Port Size: 3/4”
• Warranty: 3 Years from date of purchase
• Dimension 15” x 9-1/4” x 8”
• Weight: 13.6 lbs

Delavan 90600 forged steel 540 RPM quick coupler. Quick couplers provide quick and simple on-off installation

Specifications
• For 5/8” Diameter pump shaft
• For 1-3/8” Diameter PTO
• Single Speed: 540 RPM
• Body: Forged steel
• Collar: Nylon
• Tooth/Spline: 6
• Weight: 1.90

• Delavan Lower Housing Assembly
• Works with Delavan 7822 & 7823 series pumps
• Note: Does not work with I-Series pumps
• Includes diaphragm, pistons, cam and bearing

• Delavan Upper Housing Assembly w/ 3/4" QA Ports
• Works with Delavan 7822FS series pumps with pressure switch
• Note: Does not work with I-Series pumps
• Includes pumps head housing and pressure switch part

• Delavan Complete Pump Head Assembly w/ 3/4" QA Ports
• Works with Delavan 7822FS series and 7822FS I-Series pumps with pressure switch

Delavan 7871-111Y-SB PowerFLO™ Advanced FB3 Series 7.0 GPM 100 PSI Diaphragm Pump with 1/2” FNPT Ports. Bypass Design – Continuous operation.

Features:
• FB3 pumps are Delavan’s new advanced 12V smooth running, five chamber diaphragm pumps that features Extended Pump Life and Improved Performance
• The FB3 is the most advanced, high flow 12V pump on the market, built with quality components, such as stainless fasteners, and high torque motors standard
• The new diaphragm retaining system allows the pump to maintain its flow for longer hours of operation in demanding applications
• The FB3 pumps feature Santoprene diaphragms and valves, to handle the FB3 pumps’ higher flow rates
• Like all Delavan diaphragm pumps, this heavy duty pump can run dry and will self-prime
• Made in the USA
• 100% Factory tested
• 2 Year warranty from date of purchase

Motor:
• Type: 12 VDC permanent magnet, totally enclosed, non-ventilated
• Leads: 12 AWG, 6” long
• Max Amps (100 PSI): 25
• Duty Cycle: See Heat Rise graph

Materials of Construction:
• Motor Shell: Coated Steel
• Housing: Polypropylene
• Valves: Santoprene
• Diaphragm: Santoprene/Stainless Steel
• Fasteners: Stainless Steel

Manufacturer Recommendation:
• If you are going to be running continuous use with any bypass model of pump, Delavan also recommends that you purchase a heat sink for the motor

Pump:
• Bypass Design – Continuous operation with internal bypass
• Type: 5-chamber positive displacement
• Capable of being run dry
• Excellent self-priming capability
• Liquid Temperature: 140° F Max.
• Priming Capabilities: 14’
• Max. Flow: 7.0 GPM
• Max Pressure: 100 PSI
• Inlet/Outlet Ports: 1/2” FNPT
• Packaging: Small box
• Weight: 9.75 lbs

Delavan 7871-111E-SB PowerFLO™ Advanced FB3 Series 7.0 GPM 60 PSI Diaphragm Pump with 1/2” FNPT Ports. Bypass Design – Continuous operation.

Features:
• FB3 pumps are Delavan’s new advanced 12V smooth running, five chamber diaphragm pumps that features Extended Pump Life and Improved Performance
• The FB3 is the most advanced, high flow 12V pump on the market, built with quality components, such as stainless fasteners, and high torque motors standard
• The new diaphragm retaining system allows the pump to maintain its flow for longer hours of operation in demanding applications
• The FB3 pumps feature Santoprene diaphragms and valves, to handle the FB3 pumps’ higher flow rates
• Like all Delavan diaphragm pumps, this heavy duty pump can run dry and will self-prime
• Made in the USA
• 100% Factory tested
• 2 Year warranty from date of purchase

Motor:
• Type: 12 VDC permanent magnet, totally enclosed, non-ventilated
• Leads: 12 AWG, 6” long
• Max Amps (60 PSI): 17
• Duty Cycle: See Heat Rise graph

Materials of Construction:
• Motor Shell: Coated Steel
• Housing: Polypropylene
• Valves: Santoprene
• Diaphragm: Santoprene/Stainless Steel
• Fasteners: Stainless Steel

Manufacturer Recommendation:
• If you are going to be running continuous use with any bypass model of pump, Delavan also recommends that you purchase a heat sink for the motor

Pump:
• Bypass Design – Continuous operation with internal bypass
• Type: 5-chamber positive displacement
• Capable of being run dry
• Excellent self-priming capability
• Liquid Temperature: 140° F Max.
• Priming Capabilities: 14’
• Max. Flow: 7.0 GPM
• Max Pressure: 60 PSI
• Inlet/Outlet Ports: 1/2” FNPT
• Packaging: Small box
• Weight: 9.75 lbs

Delavan 7870-111Y-SB PowerFLO™ FB2 Series 7.0 GPM 100 PSI Diaphragm Pump with 1/2” FNPT Ports. Bypass Design – Continuous operation.

Features:
• The FB2 pumps are heavy duty 12V, 7 GPM pumps with Santoprene diaphragms and Santoprene valves
• These FB2 5 chamber pumps are smooth running, and can run dry, and self-prime
• The pumps feature popular threaded NPTF ports
• The FB2 pumps are known for one of the highest flow rates in the 12V market
• The FB2 pumps are used in difficult applications such as roof cleaning, and de-icing
• Certified to NSF/ANSI Standard 61 & 372
• Made in the USA
• 100% Factory tested
• 2 Year warranty from date of purchase

Motor:
• Type: 12 VDC permanent magnet, totally enclosed, non-ventilated
• Leads: 12 AWG, 12” long
• Max Amps (100 PSI): 25
• Duty Cycle: See Heat Rise graph

Materials of Construction:
• Motor Shell: Coated Steel
• Housing: Polypropylene Glass Filled
• Valves: Santoprene
• Diaphragm: Santoprene
• Fasteners: Stainless Steel

NSF/ANSI Certified:
• NSF/ANSI Standard 61 - Drinking Water System Components - Health Effects
• NSF/ANSI 372 and conforms with the lead content requirements for “lead free” plumbing as defined by California, Vermont, Maryland, and Louisiana state laws and the U.S. Safe Drinking Water Act

Manufacturer Recommendation:
• If you are going to be running continuous use with any bypass model of pump, Delavan also recommends that you purchase a heat sink for the motor

Pump:
• Bypass Design – Continuous operation with internal bypass
• Type: 5-chamber positive displacement
• Capable of being run dry
• Excellent self-priming capability
• Liquid Temperature: 140° F Max.
• Priming Capabilities: 14’
• Max. Flow: 7.0 GPM
• Max Pressure: 100 PSI
• Inlet/Outlet Ports: 1/2” FNPT
• Packaging: Small box
• Weight: 9.75 lbs

Delavan PowerMAX™ Stroke Control Kit 1 Fits: 1-1/8", 1-1/4", 1-3/8", & 1-1/2" Cylinder Shafts

Delavan PowerMAX™ 30 GPM Log Splitter Kick-Off Control Valve. Delavan PowerMax Cylinders, Mono-Block and Kick-Off Valves are designed and manufactured to meet the most demanding requirements

Features:
• Constructed of high tensile strength gray cast iron
• Built-in adjustable relief valve
• Hard chrome plated spool

Recommended Hydraulic System:
• Maximum tank pressure: 500 PSI
• Maximum operating temperature: 180˚F
• Recommended system filtration: 10 micron

Specifications:
• Maximum GPM: 30
• Maximum operating pressure : 3,625 PSI
• Spool action is spring center/hydraulic kick-off
• Built-in relief valve preset at 2,250 PSI
• Kick-off pressure is non-adjustable, preset at 800 PSI
• Handle can be installed in “up” or “down” position
• Inlet / Outlet ports on the side: 3/4” NPT
• Top ports going to the cylinder: 1/2” NPT
• Packaging: Small box
• Warranty: 3 Years from date of purchase
• Weight: 8.95 lbs

Delavan PowerMAX™ 2-Stage 16 GPM Hydraulic Log Splitter Gear Pump.

Features:
• Excellent for log splitter, presser & trash compactor
• High tensile strength cast iron or aluminum construction
• Large displacement at low pressure, small displacement at high pressure 85% efficient
• These pumps are a direct bolt on replacement for most log splitters

Specifications:
• GPM: 16
• Max Working Pressure: 3,000 PSI
• Adjustable Unload Range: 400 to 900 PSI, preset @ 650 PSI
• RPM Range: 500 to 3,600
• Rotation: CW
• Inlet: 1” Tube
• Outlet: 1/2” NPT
• Packaging: Small box
• Warranty: 3 Years from date of purchase
• Weight: 6.8 lbs

Delavan PowerMAX™ PML3508-125ASAE 3.5" x 8" x 1.25" Hydraulic Cylinder. This ASAE Certified Tie-Rod Cylinder has 2,500 PSI Working Pressure and NPT Ports. Delavan PowerMax Hydraulic Cylinders are designed and manufactured to meet the most demanding requirements.

Features:
• Chromed, polished and individually heat-treated shaft provides extended cylinder life
• Built tough enough to stand up to the roughest conditions
• Pins and retainers: high tensile steel, zinc plated to prevent corrosion, comes with cotter pin retainers
• Ports: double ported NPTF for greater flexibility of assembly, unless otherwise stated, cylinders assembled with ports inline
• Piston nut: heavy duty automation grade self locking piston nut holds piston in place under high cycle loading
• Piston: ductile iron, precision machined providing a malleable bearing surface for extended cylinder life
• Piston seal: 90 durometer O-ring with anti extrusion back up washers provide sealing under high load conditions
• Tie-rods: high tensile steel to prevent failure under high pressure
• Cylinder shaft: high strength, hard chrome plated shaft provides extended cylinder life in harsh applications
• Tube: precision finished skive and burnished heavy wall steel tubing for extended seal and cylinder life
• Rod seal: Premium Double Lip Polyurethane BS profile using a double lip design for leak-free performance throughout the pressure range and longer life expectancy
• Rod cap and clevis cap: ductile iron comes with drilled oil passages, offering increased bearing surface for high shock and side load applications
• Rod wiper: Polyurethane AN or D Style provides a tough/hard material to remove contaminants from shaft surface
• Threaded shaft: (on ASAE cylinders) to accept optional mechanical stroke control (not applicable to 5 "bore cylinders)
• Rod clevis: ductile iron able to withstand continuous high load without wear or fracture
• All cylinders are 100% hydraulically tested up to 1.5 working pressure

Specifications:
• Bore: 3.5”
• Stroke: 8”
• Rod Diameter: 1.25”
• Working Pressure: 2,500 PSI
• Pin to Pin Center Retracted x Extended: 20-1/4” x 28-1/4”
• Clevis Pin Diameter: 1”
• Port Size: 1/2” FNPT
• Max Rated PSI on Full Extension: Full PSI
• Max Rated Column Load on Full Extension: 24,053 Lbs
• Packaging: Small box
• Warranty: 3 Years from date of purchase
• Weight: 29.25 lbs

Delavan PowerMAX™ PML4008-125ASAE 4.0" x 8" x 1.25" Hydraulic Cylinder. This ASAE Certified Tie-Rod Cylinder has 2,500 PSI Working Pressure and NPT Ports. Delavan PowerMax Hydraulic Cylinders are designed and manufactured to meet the most demanding requirements.

Features:
• Chromed, polished and individually heat-treated shaft provides extended cylinder life
• Built tough enough to stand up to the roughest conditions
• Pins and retainers: high tensile steel, zinc plated to prevent corrosion, comes with cotter pin retainers
• Ports: double ported NPTF for greater flexibility of assembly, unless otherwise stated, cylinders assembled with ports inline
• Piston nut: heavy duty automation grade self locking piston nut holds piston in place under high cycle loading
• Piston: ductile iron, precision machined providing a malleable bearing surface for extended cylinder life
• Piston seal: 90 durometer O-ring with anti extrusion back up washers provide sealing under high load conditions
• Tie-rods: high tensile steel to prevent failure under high pressure
• Cylinder shaft: high strength, hard chrome plated shaft provides extended cylinder life in harsh applications
• Tube: precision finished skive and burnished heavy wall steel tubing for extended seal and cylinder life
• Rod seal: Premium Double Lip Polyurethane BS profile using a double lip design for leak-free performance throughout the pressure range and longer life expectancy
• Rod cap and clevis cap: ductile iron comes with drilled oil passages, offering increased bearing surface for high shock and side load applications
• Rod wiper: Polyurethane AN or D Style provides a tough/hard material to remove contaminants from shaft surface
• Threaded shaft: (on ASAE cylinders) to accept optional mechanical stroke control (not applicable to 5 "bore cylinders)
• Rod clevis: ductile iron able to withstand continuous high load without wear or fracture
• All cylinders are 100% hydraulically tested up to 1.5 working pressure

Specifications:
• Bore: 4.0”
• Stroke: 8”
• Rod Diameter: 1.25”
• Working Pressure: 2,500 PSI
• Pin to Pin Center Retracted x Extended: 20-1/4” x 28-1/4”
• Clevis Pin Diameter: 1”
• Port Size: 1/2” FNPT
• Max Rated PSI on Full Extension: Full PSI
• Max Rated Column Load on Full Extension: 31,416 Lbs
• Packaging: Small box
• Warranty: 3 Years from date of purchase
• Weight: 35.55 lbs

Delavan PowerMAX™ 30 GPM Mono-Block Directional Control Valve, 2 Spool W/ 1st Position Float. Delavan PowerMax Cylinders, Mono-Block and Kick-Off Valves are designed and manufactured to meet the most demanding requirements

Features:
• Constructed of high tensile strength gray cast iron
• Load check on each spool to prevent the fall of a cylinder as the spool is shifted
• Hard chrome plated spool
• Built-in relief valve adjustable from 1,500 to 3,000 PSI, preset at 2,100 PSI
• 2 Spool With Float Spool available at 1st position – allows the blade to follow the contour of the ground while leveling or plowing

Specifications:
• Flow Rate: 30 GPM
• Max Pressure : 3,000 PSI
• Inlet / Outlet Ports: 3/4” NPT
• Work Ports: 1/2” NPT
• Packaging: Small box
• Warranty: 3 Years from date of purchase
• Weight: 24.0 lbs

Delavan PowerMAX™ PML2508-112ASAE 2.5" x 8" x 1.125" Hydraulic Cylinder. This ASAE Certified Tie-Rod Cylinder has 2,500 PSI Working Pressure and NPT Ports. Delavan PowerMax Hydraulic Cylinders are designed and manufactured to meet the most demanding requirements.

Features:
• Chromed, polished and individually heat-treated shaft provides extended cylinder life
• Built tough enough to stand up to the roughest conditions
• Pins and retainers: high tensile steel, zinc plated to prevent corrosion, comes with cotter pin retainers
• Ports: double ported NPTF for greater flexibility of assembly, unless otherwise stated, cylinders assembled with ports inline
• Piston nut: heavy duty automation grade self locking piston nut holds piston in place under high cycle loading
• Piston: ductile iron, precision machined providing a malleable bearing surface for extended cylinder life
• Piston seal: 90 durometer O-ring with anti extrusion back up washers provide sealing under high load conditions
• Tie-rods: high tensile steel to prevent failure under high pressure
• Cylinder shaft: high strength, hard chrome plated shaft provides extended cylinder life in harsh applications
• Tube: precision finished skive and burnished heavy wall steel tubing for extended seal and cylinder life
• Rod seal: Premium Double Lip Polyurethane BS profile using a double lip design for leak-free performance throughout the pressure range and longer life expectancy
• Rod cap and clevis cap: ductile iron comes with drilled oil passages, offering increased bearing surface for high shock and side load applications
• Rod wiper: Polyurethane AN or D Style provides a tough/hard material to remove contaminants from shaft surface
• Threaded shaft: (on ASAE cylinders) to accept optional mechanical stroke control (not applicable to 5 "bore cylinders)
• Rod clevis: ductile iron able to withstand continuous high load without wear or fracture
• All cylinders are 100% hydraulically tested up to 1.5 working pressure

Specifications:
• Bore: 2.5”
• Stroke: 8”
• Rod Diameter: 1.125”
• Working Pressure: 2,500 PSI
• Pin to Pin Center Retracted x Extended: 20-1/4” x 28-1/4”
• Clevis Pin Diameter: 1”
• Port Size: 3/8” FNPT
• Max Rated PSI on Full Extension: Full PSI
• Max Rated Column Load on Full Extension: 12,272 Lbs
• Packaging: Small box
• Warranty: 3 Years from date of purchase
• Weight: 21.6 lbs

Delavan PowerMAX™ PML3008-125ASAE 3" x 8" x 1.25" Hydraulic Cylinder. This ASAE Certified Tie-Rod Cylinder has 2,500 PSI Working Pressure and NPT Ports. Delavan PowerMax Hydraulic Cylinders are designed and manufactured to meet the most demanding requirements.

Features:
• Chromed, polished and individually heat-treated shaft provides extended cylinder life
• Built tough enough to stand up to the roughest conditions
• Pins and retainers: high tensile steel, zinc plated to prevent corrosion, comes with cotter pin retainers
• Ports: double ported NPTF for greater flexibility of assembly, unless otherwise stated, cylinders assembled with ports inline
• Piston nut: heavy duty automation grade self locking piston nut holds piston in place under high cycle loading
• Piston: ductile iron, precision machined providing a malleable bearing surface for extended cylinder life
• Piston seal: 90 durometer O-ring with anti extrusion back up washers provide sealing under high load conditions
• Tie-rods: high tensile steel to prevent failure under high pressure
• Cylinder shaft: high strength, hard chrome plated shaft provides extended cylinder life in harsh applications
• Tube: precision finished skive and burnished heavy wall steel tubing for extended seal and cylinder life
• Rod seal: Premium Double Lip Polyurethane BS profile using a double lip design for leak-free performance throughout the pressure range and longer life expectancy
• Rod cap and clevis cap: ductile iron comes with drilled oil passages, offering increased bearing surface for high shock and side load applications
• Rod wiper: Polyurethane AN or D Style provides a tough/hard material to remove contaminants from shaft surface
• Threaded shaft: (on ASAE cylinders) to accept optional mechanical stroke control (not applicable to 5 "bore cylinders)
• Rod clevis: ductile iron able to withstand continuous high load without wear or fracture
• All cylinders are 100% hydraulically tested up to 1.5 working pressure

Specifications:
• Bore: 3”
• Stroke: 8”
• Rod Diameter: 1.25”
• Working Pressure: 2,500 PSI
• Pin to Pin Center Retracted x Extended: 20-1/4” x 28-1/4”
• Clevis Pin Diameter: 1”
• Port Size: 1/2” FNPT
• Max Rated PSI on Full Extension: Full PSI
• Max Rated Column Load on Full Extension: 17,672 Lbs
• Packaging: Small box
• Warranty: 3 Years from date of purchase
• Weight: 24.0 lbs

Delavan PowerMAX™ PML2008-112ASAE 2" x 8" x 1.125" Hydraulic Cylinder. This ASAE Certified Tie-Rod Cylinder has 2,500 PSI Working Pressure and NPT Ports. Delavan PowerMax Hydraulic Cylinders are designed and manufactured to meet the most demanding requirements.

Features:
• Chromed, polished and individually heat-treated shaft provides extended cylinder life
• Built tough enough to stand up to the roughest conditions
• Pins and retainers: high tensile steel, zinc plated to prevent corrosion, comes with cotter pin retainers
• Ports: double ported NPTF for greater flexibility of assembly, unless otherwise stated, cylinders assembled with ports inline
• Piston nut: heavy duty automation grade self locking piston nut holds piston in place under high cycle loading
• Piston: ductile iron, precision machined providing a malleable bearing surface for extended cylinder life
• Piston seal: 90 durometer O-ring with anti extrusion back up washers provide sealing under high load conditions
• Tie-rods: high tensile steel to prevent failure under high pressure
• Cylinder shaft: high strength, hard chrome plated shaft provides extended cylinder life in harsh applications
• Tube: precision finished skive and burnished heavy wall steel tubing for extended seal and cylinder life
• Rod seal: Premium Double Lip Polyurethane BS profile using a double lip design for leak-free performance throughout the pressure range and longer life expectancy
• Rod cap and clevis cap: ductile iron comes with drilled oil passages, offering increased bearing surface for high shock and side load applications
• Rod wiper: Polyurethane AN or D Style provides a tough/hard material to remove contaminants from shaft surface
• Threaded shaft: (on ASAE cylinders) to accept optional mechanical stroke control (not applicable to 5 "bore cylinders)
• Rod clevis: ductile iron able to withstand continuous high load without wear or fracture
• All cylinders are 100% hydraulically tested up to 1.5 working pressure

Specifications:
• Bore: 2”
• Stroke: 8”
• Rod Diameter: 1.125”
• Working Pressure: 2,500 PSI
• Pin to Pin Center Retracted x Extended: 20-1/4” x 28-1/4”
• Clevis Pin Diameter: 1”
• Port Size: 3/8” FNPT
• Max Rated PSI on Full Extension: Full PSI
• Max Rated Column Load on Full Extension: 7,854 Lbs
• Packaging: Small box
• Warranty: 3 Years from date of purchase
• Weight: 17.3 lbs

Delavan 7871-101E-SB PowerFLO™ Advanced FB3 Series 7.0 GPM 60 PSI Diaphragm Pump with 1/2” FNPT Ports. Demand Switch – Operates only when liquid flow is required.

Features:
• FB3 pumps are Delavan’s new advanced 12V smooth running, five chamber diaphragm pumps that features Extended Pump Life and Improved Performance
• The FB3 is the most advanced, high flow 12V pump on the market, built with quality components, such as stainless fasteners, and high torque motors standard
• The new diaphragm retaining system allows the pump to maintain its flow for longer hours of operation in demanding applications
• The FB3 pumps feature Santoprene diaphragms and valves, to handle the FB3 pumps’ higher flow rates
• The FB3 pump uses a heavy duty demand switch system that extends the life of the pump by turning it off when not in use
• Like all Delavan diaphragm pumps, this heavy duty pump can run dry and will self-prime
• Made in the USA
• 100% Factory tested
• 2 Year warranty from date of purchase

Motor:
• Type: 12 VDC permanent magnet, totally enclosed, non-ventilated
• Leads: 12 AWG, 6” long
• Max Amps (60 PSI): 17
• Duty Cycle: See Heat Rise graph

Materials of Construction:
• Motor Shell: Coated Steel
• Housing: Polypropylene
• Valves: Santoprene
• Diaphragm: Santoprene/Stainless Steel
• Fasteners: Stainless Steel

Pump:
• Demand Switch – Operates only when liquid flow is required
• Type: 5-chamber positive displacement
• Capable of being run dry
• Excellent self-priming capability
• Liquid Temperature: 140° F Max.
• Priming Capabilities: 14’
• Max. Flow: 7.0 GPM
• Pressure Shut-Off: 60 PSI
• Inlet/Outlet Ports: 1/2” FNPT
• Packaging: Small box
• Weight: 9.75 lbs

Delavan 7871-101Y-SB PowerFLO™ Advanced FB3 Series 7.0 GPM 100 PSI Diaphragm Pump with 1/2” FNPT Ports. Demand Switch – Operates only when liquid flow is required.

Features:
• FB3 pumps are Delavan’s new advanced 12V smooth running, five chamber diaphragm pumps that features Extended Pump Life and Improved Performance
• The FB3 is the most advanced, high flow 12V pump on the market, built with quality components, such as stainless fasteners, and high torque motors standard
• The new diaphragm retaining system allows the pump to maintain its flow for longer hours of operation in demanding applications
• The FB3 pumps feature Santoprene diaphragms and valves, to handle the FB3 pumps’ higher flow rates
• The FB3 pump uses a heavy duty demand switch system that extends the life of the pump by turning it off when not in use
• Like all Delavan diaphragm pumps, this heavy duty pump can run dry and will self-prime
• Made in the USA
• 100% Factory tested
• 2 Year warranty from date of purchase

Motor:
• Type: 12 VDC permanent magnet, totally enclosed, non-ventilated
• Leads: 12 AWG, 6” long
• Max Amps (100 PSI): 25
• Duty Cycle: See Heat Rise graph

Materials of Construction:
• Motor Shell: Coated Steel
• Housing: Polypropylene
• Valves: Santoprene
• Diaphragm: Santoprene/ Stainless Steel
• Fasteners: Stainless Steel

Pump:
• Demand Switch – Operates only when liquid flow is required
• Type: 5-chamber positive displacement
• Capable of being run dry
• Excellent self-priming capability
• Liquid Temperature: 140° F Max.
• Priming Capabilities: 14’
• Max. Flow: 7.0 GPM
• Pressure Shut-Off: 100 PSI
• Inlet/Outlet Ports: 1/2” FNPT
• Packaging: Small box
• Weight: 9.75 lbs

Delavan PowerFLO™ 7822FS Flex Series 2.2 GPM 60 PSI Diaphragm Pump with 3/4” Quick Attach Ports. Thanks to the new 3/4” Quick Attach adapter system and bolt pattern, the Flex Pump can fit into most competitor spray systems that use 3/4” quick attach with ease. The new Flex Pump will be able to replace your old pump and provide a new level of performance and life. You can figuratively speaking “feel the difference in weight and productivity” between the two pumps. The new Delavan 12 Volt Flex Pumps represent years of testing and improvements, with state of the art components like improved pressure switches, efficient valve design and a new mounting and attachment system. These features create the best value in 12 Volt diaphragm pumps for your sprayer.

Features:
• Certified to NSF/ANSI Standard 61 & 372
• Made in the USA
• 100% Factory tested
• 2 Year warranty from date of purchase
• This demand pump will turn off when the spray gun or boom is turned off, saving energy and increasing the life of the pump

Motor:
• Type: 12 VDC permanent magnet, totally enclosed, non-ventilated
• Leads: 14 AWG, 6” long with 2-pin connector
• Max Amps: 8.5
• Duty Cycle: See Heat Rise graph

Materials of Construction:
• Motor Shell: Coated Steel
• Housing: Polypropylene
• Valves: Viton
• Diaphragm: Santoprene
• Fasteners: Stainless Steel

NSF/ANSI Certified:
• NSF/ANSI Standard 61 - Drinking Water System Components - Health Effects
• NSF/ANSI 372 and conforms with the lead content requirements for “lead free” plumbing as defined by California, Vermont, Maryland, and Louisiana state laws and the U.S. Safe Drinking Water Act

Pump:
• Demand Switch – Operates only when liquid flow is required
• Type: 3-chamber positive displacement
• Capable of being run dry
• Excellent self-priming capability
• Liquid Temperature: 140°F Max.
• Priming Capabilities: 14’
• Max. Flow: 2.2 GPM
• Pressure Shut-Off: 60 PSI
• Inlet/Outlet Ports: 3/4 Quick Attach
• Packaging: Small box
• Weight: 6.0 lbs

Delavan PowerFLO™ 5850 Extreme Duty Series 5.0 GPM 45 PSI Diaphragm Pump. The 5850ED five chamber pump features Extreme Duty Geolast® diaphragms that have extended life when pumping chemicals with petroleum products. Demand Switch – Operates only when liquid flow is required.

Features:
• Geaolast® diaphragm installed ensuring longer pump life when spraying harsh chemicals
• Made in the USA
• 100% Factory tested
• 2 Year warranty from date of purchase

Motor:
• Type: 12 VDC permanent magnet, totally enclosed, non-ventilated
• Leads: 14 AWG, 6” long with 2-pin connector
• Max Amps: 16
• Duty Cycle: See Heat Rise graph

Materials of Construction:
• Motor Shell: Coated Steel
• Housing: Polypropylene
• Valves: Viton
• Diaphragm: Geolast®
• Fasteners: Stainless Steel

Pump:
• Demand Switch – Operates only when liquid flow is required
• Type: 5-chamber positive displacement
• Capable of being run dry
• Excellent self-priming capability
• Liquid Temperature: 140° F Max.
• Priming Capabilities: 14’
• Max. Flow: 5.0 GPM
• Pressure Shut-Off: 45 PSI
• Inlet/Outlet Ports: 1/2” FNPT
• Packaging: Small box
• Weight: 6.0 lbs

Delavan PowerFLO™ 7812 Extreme Duty Series 2.0 GPM 60 PSI Diaphragm Pump with 3/8” FNPT Ports. The 7812ED pump features Extreme Duty Geolast® diaphragms that have extended life when pumping chemicals with petroleum products. Demand Switch – Operates only when liquid flow is required

Features:
• Geaolast® diaphragm installed ensuring longer pump life when spraying harsh chemicals
• Made in the USA
• 100% Factory tested
• 2 Year warranty from date of purchase

Motor:
• Type: 12 VDC permanent magnet, totally enclosed, non-ventilated
• Leads: 14 AWG, 6” long with 2-pin connector
• Max Amps: 8.5
• Duty Cycle: See Heat Rise graph

Materials of Construction:
• Motor Shell: Coated Steel
• Housing: Polypropylene
• Valves: Viton
• Diaphragm: Geolast®
• Fasteners: Stainless Steel

Pump:
• Demand Switch – Operates only when liquid flow is required
• Type: 3-chamber positive displacement
• Capable of being run dry
• Excellent self-priming capability
• Liquid Temperature: 140°F Max.
• Priming Capabilities: 14’
• Max. Flow: 2.0 GPM
• Pressure Shut-Off: 60 PSI
• Inlet/Outlet Ports: 3/8” FNPT
• Packaging: Small box
• Weight: 6.0 lbs

• Delavan 5/8" QA X 3/8" HB Elbow Fitting w/ O-Ring, Nylon (7800 Series, QA Only)
• Works with 7800 Series Quick Attach Pumps

• Delavan 5/8" QA X 1/2" HB Elbow Fitting w/ O-Ring, Nylon (7800 Series, QA Only)
• Works with 7800 Series Quick Attach Pumps

• Delavan 5/8" QA X 3/8" FNPT Straight Fitting w/ O-Ring, Black Nylon (7800 Series, QA Only)
• Works with 7800 Series Quick Attach Pumps

• Delavan 5/8" QA X 1/2" FNPT Straight Fitting w/ O-Ring, Black Nylon (7800 Series, QA Only)
• Works with 7800 Series Quick Attach Pumps

Delavan PowerFLO™ 5850 Series 5.0 GPM 45 PSI Diaphragm Pump. Demand Switch – Operates only when liquid flow is required.

Features:
• Certified to NSF/ANSI Standard 61 & 372
• Made in the USA
• 100% Factory tested
• 2 Year warranty from date of purchase

Motor:
• Type: 12 VDC permanent magnet, totally enclosed, non-ventilated
• Leads: 14 AWG, 6” long with 2-pin connector
• Amps: 6.0 – 16
• Duty Cycle: See Heat Rise graph

Materials of Construction:
• Motor Shell: Coated Steel
• Housing: Polypropylene
• Valves: Viton
• Diaphragm: Santoprene
• Fasteners: Stainless Steel

NSF/ANSI Certified:
• NSF/ANSI Standard 61 - Drinking Water System Components - Health Effects
• NSF/ANSI 372 and conforms with the lead content requirements for “lead free” plumbing as defined by California, Vermont, Maryland, and Louisiana state laws and the U.S. Safe Drinking Water Act

Pump:
• Demand Switch – Operates only when liquid flow is required
• Type: 5-chamber positive displacement
• Capable of being run dry
• Excellent self-priming capability
• Liquid Temperature: 140° F Max.
• Priming Capabilities: 14’
• Max. Flow: 5.0 GPM
• Pressure Shut-Off: 45 PSI
• Inlet/Outlet Ports: 1/2” FNPT
• Packaging: Small box
• Weight: 6.0 lbs

Delavan PowerFLO™ 7812 I-Series 2.1 GPM 60 PSI Diaphragm Pump with 3/8” FNPT Ports. Demand Switch – Operates only when liquid flow is required

Features:
• 100% Factory tested
• 2 Year warranty from date of purchase

Motor:
• Type: 12 VDC permanent magnet, totally enclosed, non-ventilated
• Leads: 14 AWG, 6” long with 2-pin connector
• Max Amps: 8.5
• Duty Cycle: See Heat Rise graph

Materials of Construction:
• Motor Shell: Coated Steel
• Housing: Polypropylene
• Valves: Santoprene
• Diaphragm: Santoprene
• Fasteners: Zinc plated

Pump:
• Demand Switch – Operates only when liquid flow is required
• Type: 3-chamber positive displacement
• Capable of being run dry
• Excellent self-priming capability
• Liquid Temperature: 140°F Max.
• Priming Capabilities: 14’
• Max. Flow: 2.1 GPM
• Pressure Shut-Off: 60 PSI
• Inlet/Outlet Ports: 3/8” FNPT
• Packaging: Small box
• Weight: 6.0 lbs

Delavan PowerFLO™ 5836 Series 3.6 GPM 60 PSI Diaphragm Pump. Bypass Design – Continuous operation

Features:
• Certified to NSF/ANSI Standard 61 & 372
• Made in the USA
• 100% Factory tested
• 2 Year warranty from date of purchase

Motor:
• Type: 12 VDC permanent magnet, totally enclosed, non-ventilated
• Leads: 14 AWG, 12” long with Delphi Weatherproof Electrical 2 Pin Connector
• Amps: 11 Max
• Duty Cycle: See Heat Rise graph

Materials of Construction:
• Motor Shell: Coated Steel
• Housing: Polypropylene
• Valves: Viton
• Diaphragm: Santoprene
• Fasteners: Stainless Steel

NSF/ANSI Certified:
• NSF/ANSI Standard 61 - Drinking Water System Components - Health Effects
• NSF/ANSI 372 and conforms with the lead content requirements for “lead free” plumbing as defined by California, Vermont, Maryland, and Louisiana state laws and the U.S. Safe Drinking Water Act

Manufacturer Recommendation:
• If you are going to be running continuous use with any bypass model of pump, Delavan also recommends that you purchase a heat sink for the motor

Pump:
• Bypass Design – Continuous operation
• Type: 5-chamber positive displacement
• Capable of being run dry
• Excellent self-priming capability
• Liquid Temperature: 140° F Max.
• Priming Capabilities: 14’
• Max. Flow: 3.6 GPM
• Max Pressure: 60 PSI
• Pressure Settings: 70 PSI
• Inlet/Outlet Ports: 1/2” FNPT
• Packaging: Small box
• Weight: 7.0 lbs