General Pump

General EP1812S17 Triplex EP Series 1,750 RPM Solid Shaft Plunger Pump.

Features:
• Triplex plunger pump
• New Forged brass manifold
• New plunger guide bushing (patent pending)
• Solid ceramic plungers with dual guide system
• New dual diameter plunger guide
• New optimized outlet valves
• New dual lip oil seal

Specifications Sheet

Specifications:
• Solid Shaft for Belt or Gear Drive
• Max. Volume: 4.0 GPM
• Max. Discharge Pressure: 2,500 PSI
• Horsepower: 6.6 HP
• Max. Pump Speed: 1,750 RPM
• Oil Capacity: 15 oz
• Max. Fluid Temp.: 165 degrees F.
• Inlet Port Thread: 1/2”-14 BSP-F
• Discharge Port Thread: 3/8”-19 BSP-F
• Shaft Diameter: .945 in./24 mm
• Dimensions – Nominal: 9.5” x 8.38” x 5.1”
• Weight: 15.4 lb.

General EP1510S34 Triplex EP Series 3,400 RPM Solid Shaft Plunger Pump.

Features:
• Triplex plunger pump
• New Forged brass manifold
• New plunger guide bushing (patent pending)
• Solid ceramic plungers with dual guide system
• New dual diameter plunger guide
• New optimized outlet valves
• New dual lip oil seal

Specifications Sheet

Specifications:
• Solid Shaft for Belt or Gear Drive
• Max. Volume: 4.2 GPM
• Max. Discharge Pressure: 3,045 PSI
• Horsepower: 8.7 HP
• Max. Pump Speed: 3,400 RPM
• Oil Capacity: 15 oz
• Max. Fluid Temp.: 165 degrees F.
• Inlet Port Thread: 1/2”-14 BSP-F
• Discharge Port Thread: 3/8”-19 BSP-F
• Shaft Diameter: .945 in./24 mm
• Dimensions – Nominal: 9.5” x 8.38” x 5.1”
• Replaces TT9441
• Weight: 15.4 lb.

4,200 PSI 4.0 GPM General EP1313G8U/IF Direct Drive Pump with built-in unloader and injector

Features:
• Features built-in unloader (U) or unloader and fixed injector (UIF)
• New Forged brass manifold, increases working pressure to 4,200 PSI
• New plunger guide bushing (patent pending)
• Solid ceramic plungers with dual guide system
• New dual diameter plunger guide
• New optimized outlet valves
• New dual lip oil seal
• 1” Hollow shaft, flanged for direct couple to gas engines (SAE J609B)

Data Sheet

Specifications:
• General EP1313G8UIF Pump with SAE J609 Gas Flange
• Max. Volume: 4.0 GPM
• Max. Discharge Pressure: 4,200 PSI
• Max. Pump Speed: 3,400 RPM
• Shaft Diameter: 1” Hollow
• Max. Horsepower Requirements: 14.5 GHP
• Max. Fluid Temp.: 165º F
• Oil Capacity: 15 oz.
• Inlet Port Thread: 1/2"-14 BSP-F
• Discharge Port Thread: 3/8"-19 BSP-M
• Dimensions: 11.2"x9.6"x7.6"
• Replaces TX1510G8UIA
• Weight: 15.9 lb

General ET1505E34UTSL 2,610 PSI 2.1 GPM (Left Handed) Direct Drive Pump with Total Start-Stop flanged to direct couple on electric NEMA 56 C motors

Features:
• Total start-stop feature allows flow to activate electric motor
• Built-in unloader
• Nickel-plated cast manifold manufactured like heavy-duty pump line
• New generation seal package
• New dust protection chamber
• Solid ceramic plungers
• New oversized plunger guide
• New optimized inlet and outlet valves
• New oil seal
• Left side shaft, right side manifold

Specifications:
• Max. Volume: 2.1 GPM
• Max. Discharge Pressure: 2,610 PSI
• Max. Horsepower Requirements: 3.8 EBHP
• Max. Pump Speed: 3,400 RPM
• Max. Fluid Temp.: 165º F
• Oil Capacity: 8.5 oz
• Inlet Port Thread: 1/2"-10 BSP-F
• Discharge Port Thread: 3/8"-13 BSP-F
• Shaft Diameter: 5/8” Hollow
• Dimensions – Nominal: 8" x 7.4" x 4.7"
• Weight: 11.0 lb

General ET1504E34UTSL 2,610 PSI 2.0 GPM (Left Handed) Direct Drive Pump with Total Start-Stop flanged to direct couple on electric NEMA 56 C motors

Features:
• Total start-stop feature allows flow to activate electric motor
• Built-in unloader
• Nickel-plated cast manifold manufactured like heavy-duty pump line
• New generation seal package
• New dust protection chamber
• Solid ceramic plungers
• New oversized plunger guide
• New optimized inlet and outlet valves
• New oil seal
• Left side shaft, right side manifold

ET Series Spec Sheet

Specifications:
• Max. Volume: 2.0 GPM
• Max. Discharge Pressure: 2,610 PSI
• Max. Horsepower Requirements: 3.6 EBHP
• Max. Pump Speed: 3,400 RPM
• Max. Fluid Temp.: 165º F
• Oil Capacity: 8.5 oz
• Inlet Port Thread: 1/2"-10 BSP-F
• Discharge Port Thread: 3/8"-13 BSP-F
• Shaft Diameter: 5/8” Hollow
• Dimensions – Nominal: 8" x 7.4" x 4.7"
• Weight: 11.0 lb

General ET1506E34UTSL 2,610 PSI 2.9 GPM (Left Handed) Direct Drive Pump with Total Start-Stop flanged to direct couple on electric NEMA 56 C motors

Features:
• Total start-stop feature allows flow to activate electric motor
• Built-in unloader
• Nickel-plated cast manifold manufactured like heavy-duty pump line
• New generation seal package
• New dust protection chamber
• Solid ceramic plungers
• New oversized plunger guide
• New optimized inlet and outlet valves
• New oil seal
• Left side shaft, right side manifold

ET Series Spec Sheet

Specifications:
• Max. Volume: 2.9 GPM
• Max. Discharge Pressure: 2,610 PSI
• Max. Horsepower Requirements: 5.2 EBHP
• Max. Pump Speed: 3,400 RPM
• Max. Fluid Temp.: 165º F
• Oil Capacity: 8.5 oz
• Inlet Port Thread: 1/2"-10 BSP-F
• Discharge Port Thread: 3/8"-13 BSP-F
• Shaft Diameter: 5/8” Hollow
• Dimensions – Nominal: 8" x 7.4" x 4.7"
• Weight: 11.0 lb

3,045 PSI 3.4 GPM General EP1508G8 Direct Drive Pump Made Ready W/ PULSAR4KHPEZ EZ Start Unloader. Pump is ready to use right out of the box

PUMP:
• General EP1508G8 Pump with SAE J609 Gas Flange
• Direct Drive with Gas Flange 9.0-13.0 HP SAE
• Max. Volume: 3.4 GPM
• Max. Discharge Pressure: 3,045 PSI
• Max. Pump Speed: 3,400 RPM
• Shaft Diameter: 1” Hollow
• Max. Horsepower Requirements: 10.6 GHP
• Max. Fluid Temp.: 165º F
• New Forged brass manifold , increases working pressure to 4,000 PSI
• Solid ceramic plungers with dual guide system

COMPONENTS:
• General EP1508G8 Triplex Plunger Pump
• PULSAR4KHPEZ EZ Start Unloader 4,050 PSI, 10 GPM
• Thermal relief valve
• 3/8” Hose Barb and Clamp Keeps Hose Secure and Sealed
• 3/4” Garden Hose Inlet Fitting with 1/4” Side Port
• 3/8” QC brass socket Installed and 3/8” QC Plug Included
• Mounting bolts
• Note: Pumps are not tested prior to shipping and unloader will need to be adjusted
• Weight: 19.90 lb

General Pump DCFSCP20GZ 20" Hammerhead Professional Flat Surface Cleaner. The gun has a revolutionary compensating design to reduce fatigue. The cleaner glides easily across the surface uniformly cleaning pool decks, sidewalks, garage floors and more

FEATURES
• Compensating gun feature
• Full 20” cleaning path
• Heavy-duty anodized aluminum components
• Rugged ABS cover
• Swivel has grease zerk fitting for bearing lubrication
• Two Stainless Steel bearings for better performance
• Stainless Steel inlet filter for water filtration
• Supplied with 2-nozzle rotating arm
• Note: Caster Kit Not Included (Optional Caster Kit: P/N 2100200 available)

SPECIFICATIONS
• Max Flow: 8 GPM
• Operating Pressure: 1,000 – 4,000 PSI
• Max. Temp.: 180° F
• Nozzles: 925020M (2)
• Trigger Gun Inlet: 3/8" NPT-F
• Dimensions-Retracted 70” x 21” x 21”
• Shipping Weight 24 lbs

4,000 PSI 4.0 GPM General EP1313G8 Direct Drive Pump Made Ready W/ PULSAR4KHPEZ EZ Start Unloader. Pump is ready to use right out of the box

PUMP:
• General EP1313G8 Pump with SAE J609 Gas Flange
• Direct Drive with Gas Flange 9.0-13.0 HP SAE
• Max. Volume: 4.0 GPM
• Max. Discharge Pressure: 4,000 PSI
• Max. Pump Speed: 3,400 RPM
• Shaft Diameter: 1” Hollow
• Max. Horsepower Requirements: 14.5 GHP
• Max. Fluid Temp.: 165º F
• New Forged brass manifold , increases working pressure to 4,000 PSI
• Solid ceramic plungers with dual guide system

COMPONENTS:
• General EP1313G8 Triplex Plunger Pump
• PULSAR4KHPEZ EZ Start Unloader 4,050 PSI, 10 GPM
• Thermal relief valve
• 3/8” Hose Barb and Clamp Keeps Hose Secure and Sealed
• 3/4” Garden Hose Inlet Fitting with 1/4” Side Port
• 3/8” QC brass socket and 3/8” QC Plug Included
• Mounting bolts
• Note: Pumps are not tested prior to shipping and unloader will need to be adjusted
• Weight: 19.90 lb

1,500 PSI 2.11 GPM General TT9061EBFUI Direct Couple to Electric Motors (NEMA 56C) with Built In Unloader and Downstrean injector

Features:
• Forged brass manifold with exclusive lifetime warranty
• Die-cast annodized aluminum, oil-bath crankcase
• Solid ceramic plungers with continuously lubricated packings
• The original Interpump unitized, stainless steel, K01 inlet and outlet valves
• Ideal for all general cleaning, RO and misting applications
• Comes standard with NEMA 56C electric motor mounting flange
• Also available in “L” left-handed versions

Specifications Sheet

Specifications:
• Maximum Volume: 2.11 GPM
• Maximum Discharge Pressure: 1,500 PSI
• Maximum Pump Speed: 3,400 RPM
• Maximum Inlet Pressure: 125 PSI
• Oil Capacity: 11.2 oz.
• Maximum Fluid Temperature: 165°F
• Inlet Port Thread: 3/8-19 BSPP-F
• Discharge Port Thread: 1/4-19 BSPP-F
• Shaft Diameter 5/8 in. / 16 mm
• Horespower: 2.2 EBHP
• Weight 12.0 lbs.

General EP1813S17 Triplex EP Series 1,750 RPM Solid Shaft Plunger Pump.

Features:
• Triplex plunger pump
• New Forged brass manifold
• New plunger guide bushing (patent pending)
• Solid ceramic plungers with dual guide system
• New dual diameter plunger guide
• New optimized outlet valves
• New dual lip oil seal

Specifications Sheet

WARNING: High Pressure Systems require a primary pressure regulating device (i.e. regulator, unloader) and a secondary pressure relief device (i.e. pop-off valve, relief valve). Failure to install such relief devices properly could result in personal injury or damage to pump or property. GP and PRI Industries do not assume any liability or responsibility for the operation of the user’s high pressure system.

Specifications:
• Solid Shaft for Belt or Gear Drive
• Max. Volume: 4.2 GPM
• Max. Discharge Pressure: 2,900 PSI
• Horsepower: 8.3 HP
• Max. Pump Speed: 1,750 RPM
• Maximum Inlet Pressure: 125 PSI
• Oil Capacity: 15 oz
• Max. Fluid Temp.: 165 degrees F.
• Inlet Port Thread: 1/2”-14 BSP-F
• Discharge Port Thread: 3/8”-19 BSP-F
• Shaft Diameter: .945 in./24 mm
• Dimensions – Nominal: 9.5” x 8.38” x 5.1”
• Replaces TX1813S17
• Note: Item for sale is PUMP ONLY as shown in picture and does not include unloader which is required for proper operation
• Weight: 15.4 lb.

General EP1513S17 Triplex EP Series 1,750 RPM Solid Shaft Plunger Pump.

Features:
• Triplex plunger pump
• New Forged brass manifold
• New plunger guide bushing (patent pending)
• Solid ceramic plungers with dual guide system
• New dual diameter plunger guide
• New optimized outlet valves
• New dual lip oil seal

Specifications Sheet

WARNING: High Pressure Systems require a primary pressure regulating device (i.e. regulator, unloader) and a secondary pressure relief device (i.e. pop-off valve, relief valve). Failure to install such relief devices properly could result in personal injury or damage to pump or property. GP and PRI Industries do not assume any liability or responsibility for the operation of the user’s high pressure system.

Specifications:
• Solid Shaft for Belt or Gear Drive
• Max. Volume: 3.2 GPM
• Max. Discharge Pressure: 3,045 PSI
• Horsepower: 6.5 EBHP
• Max. Pump Speed: 1,750 RPM
• Maximum Inlet Pressure: 125 PSI
• Oil Capacity: 15 oz
• Max. Fluid Temp.: 165 degrees F.
• Inlet Port Thread: 1/2”-14 BSP-F
• Discharge Port Thread: 3/8”-19 BSP-F
• Shaft Diameter: .945 in./24 mm
• Dimensions – Nominal: 9.5” x 8.38” x 5.1”
• Replaces TX1513S17
• Note: Item for sale is PUMP ONLY as shown in picture and does not include unloader which is required for proper operation
• Weight: 15.4 lb.

General EP1512S17 Triplex EP Series 1,750 RPM Solid Shaft Plunger Pump.

Features:
• Triplex plunger pump
• New Forged brass manifold
• New plunger guide bushing (patent pending)
• Solid ceramic plungers with dual guide system
• New dual diameter plunger guide
• New optimized outlet valves
• New dual lip oil seal

Specifications Sheet

WARNING: High Pressure Systems require a primary pressure regulating device (i.e. regulator, unloader) and a secondary pressure relief device (i.e. pop-off valve, relief valve). Failure to install such relief devices properly could result in personal injury or damage to pump or property. GP and PRI Industries do not assume any liability or responsibility for the operation of the user’s high pressure system.

Specifications:
• Solid Shaft for Belt or Gear Drive
• Max. Volume: 2.9 GPM
• Max. Discharge Pressure: 3,045 PSI
• Horsepower: 6.0 EBHP
• Max. Pump Speed: 1,750 RPM
• Maximum Inlet Pressure: 125 PSI
• Oil Capacity: 15 oz
• Max. Fluid Temp.: 165 degrees F.
• Inlet Port Thread: 1/2”-14 BSP-F
• Discharge Port Thread: 3/8”-19 BSP-F
• Shaft Diameter: .945 in./24 mm
• Dimensions – Nominal: 9.5” x 8.38” x 5.1”
• Note: Item for sale is PUMP ONLY as shown in picture and does not include unloader which is required for proper operation
• Weight: 15.4 lb.

2,610 PSI 3.2 GPM General PMRET1507G6 Direct Drive Pump Made Ready W/ PULSAR4KHPEZ EZ Start Unloader. Pump is ready to use right out of the box

PUMP:
• General ET1507G6 Pump with SAE J609A Gas Flange
• Direct Drive with Gas Flange 5.0-7.0 HP SAE
• Max. Volume: 3.2 GPM
• Max. Discharge Pressure: 2,610 PSI
• Max. Pump Speed: 3,400 RPM
• Shaft Diameter: 3/4” Hollow
• Max. Horsepower Requirements: 7.6 GHP
• Max. Fluid Temp.: 165º F
• Nickel-plated cast manifold manufactured like heavy-duty pump line
• Solid ceramic plungers

COMPONENTS:
• General ET1507G6 Triplex Plunger Pump
• PULSAR4KHPEZ EZ Start Unloader 4,050 PSI, 10 GPM
• Thermal relief valve
• 3/8” Hose Barb and Clamp Keeps Hose Secure and Sealed
• 3/4” Garden Hose Inlet Fitting with 1/4” Side Port
• 3/8” QC brass socket Installed and 3/8” QC Plug Included
• Mounting bolts
• Note: Pumps are not tested prior to shipping and unloader will need to be adjusted
• Weight: 14.90 lb

General Pump YGR1000P Gear Reducer for 2.2 to 1, 1″ Shafted Engines, Up to 24 HP, J609A Flange, 47, 47SS and 66 Series pumps

Features:
• Compact and lightweight
• Hardened steel helical gears for quiet operation
• Oil bath lubrication
• Dual bearing design for extended life
• J609a Flange mounts to most gasoline engines

Specifications:
• Horse Power: 18 - 24
• Drive Ratio: 2.176:1
• Maximum Pump Speed: 1,450 RPM
• Oil Capacity: 10 Oz
• Oil Grade: SAE90 Gear Lube
• Input (motor) Shaft Ø": 1”
• Output (pump) Shaft Ø": 24 mm
• Motor Flange (SAE): J609A
• Pump Flange: Fits 47, 47SS and 66 Series General Pump
• Weight: 5.8 lb.

General Pump DCFSCP18GZ 18" Hammerhead Professional Flat Surface Cleaner. The gun has a revolutionary compensating design to reduce fatigue. The cleaner glides easily across the surface uniformly cleaning pool decks, sidewalks, garage floors and more

FEATURES
• Compensating gun feature
• Full 18” cleaning path
• Heavy-duty anodized aluminum components
• Rugged ABS cover
• Swivel has grease zerk fitting for bearing lubrication
• Two Stainless Steel bearings for better performance
• Stainless Steel inlet filter for water filtration
• Supplied with 2-nozzle rotating arm
• Note: Caster Kit Not Included (Optional Caster Kit: P/N 2100200 available)

SPECIFICATIONS
• Max Flow: 8 GPM
• Operating Pressure: 1,000 – 4,000 PSI
• Max. Temp.: 180° F
• Nozzles: 925020M (2)
• Trigger Gun Inlet: 3/8" NPT-F
• Dimensions-Retracted 70”x18.3”x18.3”
• Shipping Weight 19 lbs

General Pump 100687 Clutch w/Mounting Plate 47, 66 and 59(ES) Series, 12V, Dual Groove. Mobile Clutch for 24mm Solid Shaft Pump

Features:
• Solid forged rotor. A one-piece solid forged rotor means no chance of internal parts separation. They have an even wall thickness around the coil which gives optimum flux distribution, maximizing torque.
• Different coil voltages available. 12 volt is the most common; 24 volt clutches are also available.
• High temperature, longer-life grease. Our special long-life grease has shown a significant improvement in life over other standard high temp greases.
• E-coating. Where possible, all parts in the clutch are e-coated to give maximum corrosion protection.
• High-temperature epoxy coil. To help prevent failure from vibration and outside contaminants, all coils are sealed in the coil shell with a high-temperature epoxy coating.
• Forged machined pulley. All GP models use a heavy-duty machined pulley. A stronger pulley resists damage

Data Sheet

Specifications:
• Pulley Size & Type: 7" - A Groove, 24mm Shaft
• Width: 2.25"
• Torque After Burnishing: 75 - 95 lbs.
• Power Requirement: 12V 47 Watts
• Weight: 8.0 lbs

General Pump 100688 Clutch w/Mounting Plate 44, 50, 63 and 58 (ES) Series, 12V, Dual Groove. Mobile Clutch for 24mm Solid Shaft Pump

Features:
• Solid forged rotor. A one-piece solid forged rotor means no chance of internal parts separation. They have an even wall thickness around the coil which gives optimum flux distribution, maximizing torque.
• Different coil voltages available. 12 volt is the most common; 24 volt clutches are also available.
• High temperature, longer-life grease. Our special long-life grease has shown a significant improvement in life over other standard high temp greases.
• E-coating. Where possible, all parts in the clutch are e-coated to give maximum corrosion protection.
• High-temperature epoxy coil. To help prevent failure from vibration and outside contaminants, all coils are sealed in the coil shell with a high-temperature epoxy coating.
• Forged machined pulley. All GP models use a heavy-duty machined pulley. A stronger pulley resists damage

Data Sheet

Specifications:
• Pulley Size & Type: 7" - A Groove, 24mm Shaft
• Width: 2.25"
• Torque After Burnishing: 75 - 95 lbs.
• Power Requirement: 12V 47 Watts
• Weight: 8.0 lbs

General Pump 100719 Clutch w/Mounting Plate 47, 66 and 59(ES) Series, 12V, Single Groove. Mobile Clutch for 24mm Solid Shaft Pump

Features:
• Solid forged rotor. A one-piece solid forged rotor means no chance of internal parts separation. They have an even wall thickness around the coil which gives optimum flux distribution, maximizing torque.
• Different coil voltages available. 12 volt is the most common; 24 volt clutches are also available.
• High temperature, longer-life grease. Our special long-life grease has shown a significant improvement in life over other standard high temp greases.
• E-coating. Where possible, all parts in the clutch are e-coated to give maximum corrosion protection.
• High-temperature epoxy coil. To help prevent failure from vibration and outside contaminants, all coils are sealed in the coil shell with a high-temperature epoxy coating.
• Forged machined pulley. All GP models use a heavy-duty machined pulley. A stronger pulley resists damage

Data Sheet

Specifications:
• Pulley Size & Type: 7" - A Groove, 24mm Shaft
• Width: 2.25"
• Torque After Burnishing: 75 - 95 lbs.
• Power Requirement: 12V 47 Watts
• Weight: 8.0 lbs

General Pump 100720 Clutch w/Mounting Plate 44, 50, 63 and 58 (ES) Series, 12V, Single Groove. Mobile Clutch for 24mm Solid Shaft Pump

Features:
• Solid forged rotor. A one-piece solid forged rotor means no chance of internal parts separation. They have an even wall thickness around the coil which gives optimum flux distribution, maximizing torque.
• Different coil voltages available. 12 volt is the most common; 24 volt clutches are also available.
• High temperature, longer-life grease. Our special long-life grease has shown a significant improvement in life over other standard high temp greases.
• E-coating. Where possible, all parts in the clutch are e-coated to give maximum corrosion protection.
• High-temperature epoxy coil. To help prevent failure from vibration and outside contaminants, all coils are sealed in the coil shell with a high-temperature epoxy coating.
• Forged machined pulley. All GP models use a heavy-duty machined pulley. A stronger pulley resists damage

Data Sheet

Specifications:
• Pulley Size & Type: 7" - A Groove, 24mm Shaft
• Width: 2.25"
• Torque After Burnishing: 75 - 95 lbs.
• Power Requirement: 12V 47 Watts
• Weight: 8.0 lbs

General Pump 100719 Clutch w/Mounting Plate 47, 66 and 59(ES) Series, 24V, Dual Groove. Mobile Clutch for 24mm Solid Shaft Pump

Features:
• Solid forged rotor. A one-piece solid forged rotor means no chance of internal parts separation. They have an even wall thickness around the coil which gives optimum flux distribution, maximizing torque.
• Different coil voltages available. 12 volt is the most common; 24 volt clutches are also available.
• High temperature, longer-life grease. Our special long-life grease has shown a significant improvement in life over other standard high temp greases.
• E-coating. Where possible, all parts in the clutch are e-coated to give maximum corrosion protection.
• High-temperature epoxy coil. To help prevent failure from vibration and outside contaminants, all coils are sealed in the coil shell with a high-temperature epoxy coating.
• Forged machined pulley. All GP models use a heavy-duty machined pulley. A stronger pulley resists damage

Data Sheet

Specifications:
• Pulley Size & Type: 7" - A Groove, 24mm Shaft
• Width: 2.25"
• Torque After Burnishing: 75 - 95 lbs.
• Power Requirement: 24V 45.6 Watts
• Weight: 8.0 lbs

General Pump 100720 Clutch w/Mounting Plate 44, 50, 63 and 58 (ES) Series, 24V, Dual Groove. Mobile Clutch for 24mm Solid Shaft Pump

Features:
• Solid forged rotor. A one-piece solid forged rotor means no chance of internal parts separation. They have an even wall thickness around the coil which gives optimum flux distribution, maximizing torque.
• Different coil voltages available. 12 volt is the most common; 24 volt clutches are also available.
• High temperature, longer-life grease. Our special long-life grease has shown a significant improvement in life over other standard high temp greases.
• E-coating. Where possible, all parts in the clutch are e-coated to give maximum corrosion protection.
• High-temperature epoxy coil. To help prevent failure from vibration and outside contaminants, all coils are sealed in the coil shell with a high-temperature epoxy coating.
• Forged machined pulley. All GP models use a heavy-duty machined pulley. A stronger pulley resists damage

Data Sheet

Specifications:
• Pulley Size & Type: 7" - A Groove, 24mm Shaft
• Width: 2.25"
• Torque After Burnishing: 75 - 95 lbs.
• Power Requirement: 24V 45.6 Watts
• Weight: 8.0 lbs

1,500 PSI 2.11 GPM General TT9061EBF Direct Couple to Electric Motors (NEMA 56C)

Features:
• Forged brass manifold with exclusive lifetime warranty
• Die-cast annodized aluminum, oil-bath crankcase
• Solid ceramic plungers with continuously lubricated packings
• The original Interpump unitized, stainless steel, K01 inlet and outlet valves
• Ideal for all general cleaning, RO and misting applications
• Comes standard with NEMA 56C electric motor mounting flange
• Also available in “L” left-handed versions

Specifications Sheet

Specifications:
• Maximum Volume: 2.11 GPM
• Maximum Discharge Pressure: 1,500 PSI
• Maximum Pump Speed: 3,400 RPM
• Maximum Inlet Pressure: 125 PSI
• Oil Capacity: 11.2 oz.
• Maximum Fluid Temperature: 165°F
• Inlet Port Thread: 3/8-19 BSPP-F
• Discharge Port Thread: 1/4-19 BSPP-F
• Shaft Diameter 5/8 in. / 16 mm
• Horespower: 2.2 EBHP
• Weight 12.0 lbs.

1,500 PSI 2.11 GPM General TT9051EBF Direct Couple to Electric Motors (NEMA 56C)

Features:
• Forged brass manifold with exclusive lifetime warranty
• Die-cast annodized aluminum, oil-bath crankcase
• Solid ceramic plungers with continuously lubricated packings
• The original Interpump unitized, stainless steel, K01 inlet and outlet valves
• Ideal for all general cleaning, RO and misting applications
• Comes standard with NEMA 56C electric motor mounting flange
• Also available in “L” left-handed versions

Specifications Sheet

Specifications:
• Maximum Volume: 2.11 GPM
• Maximum Discharge Pressure: 1,500 PSI
• Maximum Pump Speed: 1,750 RPM
• Maximum Inlet Pressure: 125 PSI
• Oil Capacity: 11.2 oz.
• Maximum Fluid Temperature: 165°F
• Inlet Port Thread: 3/8-19 BSPP-F
• Discharge Port Thread: 1/4-19 BSPP-F
• Shaft Diameter 5/8 in. / 16 mm
• Horespower: 2.2 EBHP
• Weight 12.0 lbs.

General EZ4040G 4000PSI, 4.0GPM Pump is designed to direct drive on gasoline engines ranging from 9 -13 HP

Features:
• Standard SAE J609 gasoline mounting flange for up to 13 hp engines
• Forged brass manifold with an exclusive lifetime warranty and 3:1 hydrostatic rating
• Die-cast, anodized aluminum oil-bath crankcase
• Innovative one-piece plunger design to eliminate water entering crankcase
• Premium roller bearing
• 5% reduction in crankcase load compared to standard 3,000 PSI, 15 mm pumps
• Unitized stainless steel inlet and discharge valves

Specifications:
• Triplex Plunger Pump
• Direct Drive with Gas Flange 9.0-13.0 HP SAE
• Max. Volume: 4.0 GPM
• Max. Discharge Pressure: 4,000 PSI
• Max. Pump Speed: 3,400 RPM
• Shaft Diameter: 1” Hollow
• Max. Horsepower Requirements: 14.54 GHP
• Max. Fluid Temp.: 165 degrees F.
• Inlet Ports (2): 1/2-14 BSPP-F
• Discharge Ports (2): 3/8-19 BSPP-F
• Drive Side: Standard right
• Note: Item for sale is PUMP ONLY as shown in picture and does not include unloader which is required for proper operation
• Weight: 20.0 lb.

General Pump 2103410 Electric Hose Reel Motor Kit. Fits DHRA Hose Reels

FEATURES
• Allows for effortless rewinding of hose
• Free spin allows for easy pulling out of hose
• Durable powder coated finish
• Stainless steel hardware
• Long lasting hardened gears

SPECIFICATIONS
• Works with DHRA50150, DHRA50300 & DHRA50450 A Frame Hose Reels
• Voltage 12V DC
• Hose Reel Not Included
• Weight 21 lbs

2,610 PSI 2.9 GPM General PMRET1506G6 Direct Drive Pump Made Ready W/ PULSAR4KHPEZ EZ Start Unloader. Pump is ready to use right out of the box

PUMP:
• General ET1506G6 Pump with SAE J609A Gas Flange
• Direct Drive with Gas Flange 5.0-7.0 HP SAE
• Max. Volume: 2.9 GPM
• Max. Discharge Pressure: 2,610 PSI
• Max. Pump Speed: 3,400 RPM
• Shaft Diameter: 3/4” Hollow
• Max. Horsepower Requirements: 6.9 GHP
• Max. Fluid Temp.: 165º F
• New “HR” anti-corrosion surface treatment on manifold
• Solid ceramic plungers

COMPONENTS:
• General ET1506G6 Triplex Plunger Pump
• PULSAR4KHPEZ EZ Start Unloader 4,050 PSI, 10 GPM
• Thermal relief valve
• 3/8” Hose Barb and Clamp Keeps Hose Secure and Sealed
• 3/4” Garden Hose Inlet Fitting with 1/4” Side Port
• 3/8” QC brass socket and 3/8” QC Plug Included
• Mounting bolts
• Note: Pumps are not tested prior to shipping and unloader will need to be adjusted
• Weight: 14.90 lb

General ET1506E34 2,610 PSI 2.9 GPM Direct Drive Pump flanged to direct couple on electric NEMA 56 C motors

Features:
• “HR” anti-corrosion surface treatment on manifold
• New generation seal package
• Dust protection chamber
• Solid ceramic plungers
• Oversized plunger guide
• Optimized inlet and outlet valves
• Oversized crankcase Hollow shaft, flanged for direct couple to electric motors (NEMA56C)

Specifications:
• Max. Volume: 2.9 GPM
• Max. Discharge Pressure: 2,610 PSI
• Max. Horsepower Requirements: 5.2 EBHP
• Max. Pump Speed: 3,400 RPM
• Max. Fluid Temp.: 165º F
• Oil Capacity: 8.5 oz
• Inlet Port Thread: 1/2"-14 BSP-F
• Discharge Port Thread: 3/8"-19 BSP-F
• Shaft Diameter: 5/8” Hollow
• Dimensions – Nominal: 7.3" x 7.4" x 5.5"
• Weight: 11.0 lb

General ET1506E34 2,610 PSI 2.9 GPM (Left Handed) Direct Drive Pump flanged to direct couple on electric NEMA 56 C motors

Features:
• “HR” anti-corrosion surface treatment on manifold
• New generation seal package
• Dust protection chamber
• Solid ceramic plungers
• Oversized plunger guide
• Optimized inlet and outlet valves
• Oversized crankcase Hollow shaft, flanged for direct couple to electric motors (NEMA56C)

Specifications:
• Max. Volume: 2.9 GPM
• Max. Discharge Pressure: 2,610 PSI
• Max. Horsepower Requirements: 5.2 EBHP
• Max. Pump Speed: 3,400 RPM
• Max. Fluid Temp.: 165º F
• Oil Capacity: 8.5 oz
• Inlet Port Thread: 1/2"-14 BSP-F
• Discharge Port Thread: 3/8"-19 BSP-F
• Shaft Diameter: 5/8” Hollow
• Dimensions – Nominal: 7.3" x 7.4" x 5.5"
• Weight: 11.0 lb

General ET1505E34 2,610 PSI 2.1 GPM Direct Drive Pump flanged to direct couple on electric NEMA 56 C motors

Features:
• “HR” anti-corrosion surface treatment on manifold
• New generation seal package
• Dust protection chamber
• Solid ceramic plungers
• Oversized plunger guide
• Optimized inlet and outlet valves
• Oversized crankcase Hollow shaft, flanged for direct couple to electric motors (NEMA56C)

Specifications:
• Max. Volume: 2.1 GPM
• Max. Discharge Pressure: 2,610 PSI
• Max. Horsepower Requirements: 3.7 EBHP
• Max. Pump Speed: 3,400 RPM
• Max. Fluid Temp.: 165º F
• Oil Capacity: 8.5 oz
• Inlet Port Thread: 1/2"-14 BSP-F
• Discharge Port Thread: 3/8"-19 BSP-F
• Shaft Diameter: 5/8” Hollow
• Dimensions – Nominal: 7.3" x 7.4" x 5.5"
• Weight: 11.0 lb

General Pump ZH1520 Trapped Pressure Unloader Valve 2,465 PSI 52.8 GPM 1” NPT-F

Features
• Suitable for Industrial use
• Provisions for Panel Mounting
• Suitable for Industrial use
• Single bypass port
• Extremely reliable
• Easy maintenance

Specifications Sheet

Specifications
• Max Volume: 52.8 GPM
• Min Volume: 5.28 GPM
• Maximum Operating Pressure: 2,465 PSI
• Maximum Temperature: 185° F
• Inlet Port: 1" NPT-F
• Outlet Port: 1" NPT-F
• Bypass Port: 1" NPT-F
• Dimensions: 8.27” x 5.07” x 1.81”
• VRP175, VRP 175
• Weight: 4.4 Lbs

General Pump DHRA50450 3/8" x 450' or 1/2" x 375' or 5/8” x 300’ (garden hose). "A" Frame Industrial Hose Reel. Rated 5,000 PSI and up to 250° F. Ideal for use with pressure washers, sewer jetters, lawn & tree sprayers, etc. Can be used as is or can be mounted to portable cart or stacked

FEATURES
• Direct hand-crank rewind with pin lock
• Solid steel construction
• Durable gray high-gloss powder coated finish
• Full flow stainless steel swivel
• Friction brake
• Switchable swivel/handle
• HD steel welded frame
• HD sealed axle bearings
• Includes one D10032 Fitting 3/4” GH X 1/2 NPT-M

DHRA Spec Sheet

SPECIFICATIONS
• Capacity 3/8" Pressure Washer / Sewer Hose: 450’
• Capacity 5/8" Garden Hose: 325’
• Capacity 3/4" Garden Hose: 250’
• Max. PSI: 5,000
• Max Temp: 250° F.
• Color: Black
• Inlet: 1/2 NPT-F (Bushing Included, 1/2 NPT-M x 3/8 NPT-F)
• Outlet: 1/2 NPT-F (Bushing Included, 1/2 NPT-M x 3/8 NPT-F)
• Carton Dimensions: 26” x 20” x 18”
• Gross Weight 47.6 lbs