Suttner America

3/8” Suttner ST-49 Stainless Steel Rotating Sewer Jetter Nozzle, # 4.5. Does not have a forward spraying orifice, but has 3 orifices angled backwards and to the side. Slides easily into drain pipes and sewer lines flushing debris or clearing frozen pipes while attached to sewer hose. Better for removing build up from the walls of the pipe or tube.

Features
• High Quality, German engineered components
• 3 Backward ports drive the nozzle forward and flush debris
• Rotating style adds extra agitation and surface cleaning
• Corrosion resistant stainless steel and brass construction

Specifications
• Inlet: 3/8” Female
• Nozzle Size: # 4.5
• Material: Stainless steel & brass
• Maximum Pressure: 4,000 PSI
• Outside Diameter (O.D.): .94”
• Weight: .15 lb

Please use Nozzle Chart to determine proper nozzle size

Nozzle Chart

3/8” Suttner ST-49 Stainless Steel Rotating Sewer Jetter Nozzle, # 5.0. Does not have a forward spraying orifice, but has 3 orifices angled backwards and to the side. Slides easily into drain pipes and sewer lines flushing debris or clearing frozen pipes while attached to sewer hose. Better for removing build up from the walls of the pipe or tube.

Features
• High Quality, German engineered components
• 3 Backward ports drive the nozzle forward and flush debris
• Rotating style adds extra agitation and surface cleaning
• Corrosion resistant stainless steel and brass construction

Specifications
• Inlet: 3/8” Female
• Nozzle Size: # 5.0
• Material: Stainless steel & brass
• Maximum Pressure: 4,000 PSI
• Outside Diameter (O.D.): .94”
• Weight: .15 lb

Please use Nozzle Chart to determine proper nozzle size

Nozzle Chart

3/8” Suttner ST-49 Stainless Steel Rotating Sewer Jetter Nozzle, # 6.0. Does not have a forward spraying orifice, but has 3 orifices angled backwards and to the side. Slides easily into drain pipes and sewer lines flushing debris or clearing frozen pipes while attached to sewer hose. Better for removing build up from the walls of the pipe or tube.

Features
• High Quality, German engineered components
• 3 Backward ports drive the nozzle forward and flush debris
• Rotating style adds extra agitation and surface cleaning
• Corrosion resistant stainless steel and brass construction

Specifications
• Inlet: 3/8” Female
• Nozzle Size: # 6.0
• Material: Stainless steel & brass
• Maximum Pressure: 4,000 PSI
• Outside Diameter (O.D.): .94”
• Weight: .15 lb

Please use Nozzle Chart to determine proper nozzle size

Nozzle Chart

3/8” Suttner ST-49 Stainless Steel Rotating Sewer Jetter Nozzle, # 8.0. Does not have a forward spraying orifice, but has 3 orifices angled backwards and to the side. Slides easily into drain pipes and sewer lines flushing debris or clearing frozen pipes while attached to sewer hose. Better for removing build up from the walls of the pipe or tube.

Features
• High Quality, German engineered components
• 3 Backward ports drive the nozzle forward and flush debris
• Rotating style adds extra agitation and surface cleaning
• Corrosion resistant stainless steel and brass construction

Specifications
• Inlet: 3/8” Female
• Nozzle Size: # 8.0
• Material: Stainless steel & brass
• Maximum Pressure: 4,000 PSI
• Outside Diameter (O.D.): .94”
• Weight: .15 lb

Please use Nozzle Chart to determine proper nozzle size

Nozzle Chart

1/8” Suttner ST-49.3 Mini Stainless Steel Rotating Sewer Jetter Nozzle, # 5.0. Limited (or reduced) spinning speed for higher cleaning performance. Two radial jets hit the pipe wall directly with great impact, resulting in excellent cleaning capacity. Two strategically placed retracting jets provide cleaning energy as well as the thrust in one function, resulting in a low water consumption, while maximizing cleaning and flushing away the loosened residues. Housing and Rotor are hardened stainless steel parts with grinded contact surfaces for extended lifetime

Features
• High Quality, German engineered components
• 2 Rotating radial jets (90°) to the pipe wall for best cleaning results
• 2 Rotating rear jets (45°) for forward thrust and flushing away of the waste material
• Physically small for cornering ability
• Rated at 7300 PSI and 248° F

Specifications
• Inlet: 1/8” Female
• Nozzle Size: # 5.0
• 2 Side ports, 2 Backward, 0 Forward
• Material: Stainless steel
• Maximum Pressure: 7,300 PSI
• Max. Fluid Temperature: 248º F
• Outside Diameter (O.D.): 0.47”
• Length: 1.0”
• Weight: .05 lb

Please use Nozzle Chart to determine proper nozzle size

Nozzle Chart

1/8” Suttner ST-49.3 Mini Stainless Steel Rotating Sewer Jetter Nozzle, # 7.0. Limited (or reduced) spinning speed for higher cleaning performance. Two radial jets hit the pipe wall directly with great impact, resulting in excellent cleaning capacity. Two strategically placed retracting jets provide cleaning energy as well as the thrust in one function, resulting in a low water consumption, while maximizing cleaning and flushing away the loosened residues. Housing and Rotor are hardened stainless steel parts with grinded contact surfaces for extended lifetime

Features
• High Quality, German engineered components
• 2 Rotating radial jets (90°) to the pipe wall for best cleaning results
• 2 Rotating rear jets (45°) for forward thrust and flushing away of the waste material
• Physically small for cornering ability
• Rated at 7300 PSI and 248° F

Specifications
• Inlet: 1/8” Female
• Nozzle Size: # 7.0
• 2 Side ports, 2 Backward, 0 Forward
• Material: Stainless steel
• Maximum Pressure: 7,300 PSI
• Max. Fluid Temperature: 248º F
• Outside Diameter (O.D.): 0.47”
• Length: 1.0”
• Weight: .05 lb

Please use Nozzle Chart to determine proper nozzle size

Nozzle Chart

Suttner ST-5 Any Position Flow Switch. Mounts in any position with a free floating magnet configuration

Features:
• Can be mounted horizontal or vertical
• Mounts further downstream in pumping system than traditional vacuum switches, thereby minimizing potential leak points that can cause vacuum switches to close
• Easy brass reed switch replacement

Specifications:
• Max. Pressure: 5,070 PS
• Min. Pressure: 75 PSI
• Max. Flow Rate: 7.8 GPM
• Min. Flow Rate: 1 GPM
• Contact: 1 A - 250 V
• Max: Fluid Temperature: 180° F
• Cable Length: 47.0”
• Inlet & Outlet: 3/8” FNPT
• Housing: Brass
• Color: Grey
• Replaces 200005600
• Weight: 0.98 lbs

Suttner ST-5 High Flow Switch 16 GPM 1/2" FPT  3,046 PSI. Mounts in any position with a free floating magnet configuration

Features:
• Can be mounted horizontal or vertical
• Mounts further downstream in pumping system than traditional vacuum switches, thereby minimizing potential leak points that can cause vacuum switches to close
• Easy brass reed switch replacement

Specifications:
• Max. Pressure: 3,046 PS
• Min. Pressure: 75 PSI
• Max. Flow Rate: 16 GPM
• Min. Flow Rate: 4 GPM
• Contact: 1 A - 250 V
• Max: Fluid Temperature: 176° F
• Cable Length: 47.0”
• Inlet & Outlet: 1/2” FPT
• Housing: Brass
• Color: Black
• Weight: 0.98 lbs

Suttner ST-5 Vertical Mount Flow Switch. Vertical mounting position and free floating brass magnet configuration

Features:
• Vertical mounting ONLY
• Reed switch encased in protective vacuum sealed glass tube eliminating exposure to corrosive cleaning chemicals
• Mounts further downstream in pumping system than traditional vacuum switches, thereby minimizing potential leak points that can cause vacuum switches to close
• Easy reed switch replacement
• Most proven and reliable flow switches in the industry

Specifications:
• Max. Pressure: 4,380 PS
• Min. Pressure: 75 PSI
• Max. Flow Rate: 8 GPM
• Min. Flow Rate: 1 GPM
• Contact: 1 A - 250 V
• Max: Fluid Temperature: 176° F
• Cable Length: 47.0”
• Inlet & Outlet: 3/8” FNPT
• Housing: Brass
• Color: Black
• Replaces 200005500
• Weight: 0.98 lbs

Suttner ST-505 Stainless Steel Vertical Mount Flow Switch Rated to 8,700 PSI. Vertical mounting position and free floating brass magnet configuration

Features:
• Vertical mounting ONLY
• Mounts further downstream in pumping system than traditional vacuum switches, thereby minimizing potential leak points that can cause vacuum switches to close
• Easy reed switch replacement

Specifications:
• Max. Pressure: 8,700 PS
• Min. Pressure: 75 PSI
• Max. Flow Rate: 8 GPM
• Min. Flow Rate: 1 GPM
• Max Voltage: 250 V
• Max Current: 3 Amps
• Max: Fluid Temperature: 176° F
• Cable Length: 47.0”
• Inlet & Outlet: 3/8” FNPT
• Housing: Stainless Steel
• Color: Blue
• 3/8” Bonded seal #78888389 is recommended to seal inlet and outlet threads
• Weight: 0.90 lbs

Suttner ST-510 Poly Chemical Spray Gun 18.5 GPM, 365 PSI, 1/2" FPT

Features
• High Quality, German engineered components
• Reinforced polypropylene will withstand the harshest chemicals
• Gun with stainless steel V4A / AISI 316 ball being resistant to chemicals
• Ideal gun for use in soft wash applications

Specifications
• Max Pressure: 365 PSI
• Max Flow: 18.5 GPM
• Inlet: 1/2" Female NPT
• Outlet: 1/2" Female NPT
• UDOR # 15.0003.13
• Weight: 0.30 lb

Features
• High Quality, German engineered components
• Through twisting the plastic housing the high or low pressure operation is continuously adjustable
• Dumps water around nozzle to lower pressure
• Nozzle housing is made of an impact resistant plastic, manufactured of corrosion resistant material

Specifications
• Max Pressure: 3,600 PSI
• Max Flow: 8 GPM
• Max Temp: 300° F.
• Inlet: 1/4" Female NPT
• Outlet: 1/4" Female NPT
• Note: 1/4” MPT Nozzle not included
• Weight: 0.36 lb

Suttner ST-55 Sandblasting Kit #4.0 with Adjustable Sand Flow Valve. Removes coatings from almost any surface. Designed for sandblasting a variety of surfaces and capable of removing most coatings down to white metal. Graffiti clean up, paint

FEATURES:
• High Quality, German engineered components
• Adjustable sand volume valve
• Works on venturi principle
• Silver steel sand nozzle
• Use silica sand for best results
• 13 ft hose
• Grain Size 0.2 mm - 0.8 mm

SPECIFICATIONS:
• Nozzle Size: # 4.0
• Max Pressure: 3,500 PSI
• Min Flow Rate: 2 GPM
• Max Flow Rate: 8 GPM
• Max Temp: 194° F
• Sand Consumption: Max 750 lbs per hour
• Inlet: 1/4"Male NPT
• Weight: 4.92 lbs

Please use Nozzle Chart to determine proper nozzle size

Suttner ST-55 Sandblasting Kit #5.0 with Adjustable Sand Flow Valve. Removes coatings from almost any surface. Designed for sandblasting a variety of surfaces and capable of removing most coatings down to white metal. Graffiti clean up, paint

FEATURES:
• High Quality, German engineered components
• Adjustable sand volume valve
• Works on venturi principle
• Silver steel sand nozzle
• Use silica sand for best results
• 13 ft hose
• Grain Size 0.2 mm - 0.8 mm

SPECIFICATIONS:
• Nozzle Size: # 5.0
• Max Pressure: 3,500 PSI
• Min Flow Rate: 2 GPM
• Max Flow Rate: 8 GPM
• Max Temp: 194° F
• Sand Consumption: Max 750 lbs per hour
• Inlet: 1/4"Male NPT
• Weight: 4.92 lbs

Please use Nozzle Chart to determine proper nozzle size

Nozzle Chart

Suttner ST-55 Sandblasting Kit #6.0 with Adjustable Sand Flow Valve. Removes coatings from almost any surface. Designed for sandblasting a variety of surfaces and capable of removing most coatings down to white metal. Graffiti clean up, paint

FEATURES:
• High Quality, German engineered components
• Adjustable sand volume valve
• Works on venturi principle
• Silver steel sand nozzle
• Use silica sand for best results
• 13 ft hose
• Grain Size 0.2 mm - 0.8 mm

SPECIFICATIONS:
• Nozzle Size: # 6.0
• Max Pressure: 3,500 PSI
• Min Flow Rate: 2 GPM
• Max Flow Rate: 8 GPM
• Max Temp: 194° F
• Sand Consumption: Max 750 lbs per hour
• Inlet: 1/4"Male NPT
• Weight: 4.92 lbs

Please use Nozzle Chart to determine proper nozzle size

Nozzle Chart

Suttner ST-55 Sandblasting Kit #7.0 with Adjustable Sand Flow Valve. Removes coatings from almost any surface. Designed for sandblasting a variety of surfaces and capable of removing most coatings down to white metal. Graffiti clean up, paint

FEATURES:
• High Quality, German engineered components
• Adjustable sand volume valve
• Works on venturi principle
• Silver steel sand nozzle
• Use silica sand for best results
• 13 ft hose
• Grain Size 0.2 mm - 0.8 mm

SPECIFICATIONS:
• Nozzle Size: # 7.0
• Max Pressure: 3,500 PSI
• Min Flow Rate: 2 GPM
• Max Flow Rate: 8 GPM
• Max Temp: 194° F
• Sand Consumption: Max 750 lbs per hour
• Inlet: 1/4"Male NPT
• Weight: 4.92 lbs

Please use Nozzle Chart to determine proper nozzle size

Nozzle Chart

Suttner ST-55 Sandblasting Kit #8.0 with Adjustable Sand Flow Valve. Removes coatings from almost any surface. Designed for sandblasting a variety of surfaces and capable of removing most coatings down to white metal. Graffiti clean up, paint

FEATURES:
• High Quality, German engineered components
• Adjustable sand volume valve
• Works on venturi principle
• Silver steel sand nozzle
• Use silica sand for best results
• 13 ft hose
• Grain Size 0.2 mm - 0.8 mm

SPECIFICATIONS:
• Nozzle Size: # 8.0
• Max Pressure: 3,500 PSI
• Min Flow Rate: 2 GPM
• Max Flow Rate: 8 GPM
• Max Temp: 194° F
• Sand Consumption: Max 750 lbs per hour
• Inlet: 1/4"Male NPT
• Weight: 4.92 lbs

Please use Nozzle Chart to determine proper nozzle size

Nozzle Chart

Features:
• Pedal and valve are in protective housing
• Inlet and outlet are positioned to help keep hose out of the way
• Stainless steel construction for durability and stability
• Can be used in other applications

Specifications:
• Inlet: 1/4” FPT
• Outlet: 1/4” FPT
• Maximum Pressure: 7,300 PSI
• Max. Flow Rate: 21.0 GPM
• Max. Temp.: 300º F.
• Weight: 9.85 lbs.

Suttner ST-555 Professional Sandblaster #3.0 Stainless Steel with Adjustable Sand Flow. Removes coatings from almost any surface. Ideal for cleaning of machines, technical facilities, facades and masonry. Thanks to its stainless steel body, the ST-555 features utmost pressure resistance up to a continuous operating pressure of 7,250 PSI. The three symmetrical high-pressure nozzles in the blasting head provide for a flow of the blasting agent without any deflections. This is how wear of the ceramic diffuser nozzle with TPE coating is reduced to a minimum and pulse energy of the blasting agent is used optimally

FEATURES:
• High Quality, German engineered components
• The Sandblaster ST-555 has stainless steel construction 
• The sandblaster is suitable for dust-free blasting of solids with a grain size ranging from 0.4 to 0.8 mm
• With suction quantity control at the double suction pipe
• Sand blasting nozzle made of high-performance ceramics
• Inclusive: 3 hardened stainless steel nozzles

Multiple mediums can be used:
• Glass beads for cleaning of copper and bronze as well as polishing of stainless steel
• Glass powder for cleaning of stainless steel and natural stone or for removal of graffiti from light surfaces
• Slag (fine) for cleaning of sandstone or brick as well as removal of graffiti from dark surfaces
• Slag (coarse) removal of rust from metals or of old coatings and paintings. cleaning and grinding of concrete surfaces
• Sodium carbonate (water-soluble) cleaning of sensitive surfaces such as aluminum, glass, plastics, stainless steel
• Mineral blasting agent (sand) removal of rust from metals or of old coatings and paintings. Cleaning and grinding of concrete surfaces. Varnish removal

ST-555 Sandblaster on YouTube

SPECIFICATIONS:
• Nozzle Size: # 3.0
• Min Flow Rate: 3.0 GPM
• Max Flow Rate: 7.5 GPM
• Max Pressure: 7,250 PSI
• Max Temp: 212° F
• Hose Length: 13'
• Inlet: Male M22, Yoke/Stem: 14MM
• Weight: 4.92 lbs

Please use Nozzle Chart to determine proper nozzle size

Nozzle Chart

Suttner ST-555 Professional Sandblaster #4.0 Stainless Steel with Adjustable Sand Flow. Removes coatings from almost any surface. Ideal for cleaning of machines, technical facilities, facades and masonry. Thanks to its stainless steel body, the ST-555 features utmost pressure resistance up to a continuous operating pressure of 7,250 PSI. The three symmetrical high-pressure nozzles in the blasting head provide for a flow of the blasting agent without any deflections. This is how wear of the ceramic diffuser nozzle with TPE coating is reduced to a minimum and pulse energy of the blasting agent is used optimally

FEATURES:
• High Quality, German engineered components
• The Sandblaster ST-555 has stainless steel construction 
• The sandblaster is suitable for dust-free blasting of solids with a grain size ranging from 0.4 to 0.8 mm
• With suction quantity control at the double suction pipe
• Sand blasting nozzle made of high-performance ceramics
• Inclusive: 3 hardened stainless steel nozzles

Multiple mediums can be used:
• Glass beads for cleaning of copper and bronze as well as polishing of stainless steel
• Glass powder for cleaning of stainless steel and natural stone or for removal of graffiti from light surfaces
• Slag (fine) for cleaning of sandstone or brick as well as removal of graffiti from dark surfaces
• Slag (coarse) removal of rust from metals or of old coatings and paintings. cleaning and grinding of concrete surfaces
• Sodium carbonate (water-soluble) cleaning of sensitive surfaces such as aluminum, glass, plastics, stainless steel
• Mineral blasting agent (sand) removal of rust from metals or of old coatings and paintings. Cleaning and grinding of concrete surfaces. Varnish removal

ST-555 Sandblaster on YouTube

SPECIFICATIONS:
• Nozzle Size: # 4.0
• Min Flow Rate: 3.0 GPM
• Max Flow Rate: 7.5 GPM
• Max Pressure: 7,250 PSI
• Max Temp: 212° F
• Hose Length: 13'
• Inlet: Male M22, Yoke/Stem: 14MM
• Weight: 4.92 lbs

Please use Nozzle Chart to determine proper nozzle size

Nozzle Chart

Suttner ST-555 Professional Sandblaster #5.5 Stainless Steel with Adjustable Sand Flow. Removes coatings from almost any surface. Ideal for cleaning of machines, technical facilities, facades and masonry. Thanks to its stainless steel body, the ST-555 features utmost pressure resistance up to a continuous operating pressure of 7,250 PSI. The three symmetrical high-pressure nozzles in the blasting head provide for a flow of the blasting agent without any deflections. This is how wear of the ceramic diffuser nozzle with TPE coating is reduced to a minimum and pulse energy of the blasting agent is used optimally

FEATURES:
• High Quality, German engineered components
• The Sandblaster ST-555 has stainless steel construction 
• The sandblaster is suitable for dust-free blasting of solids with a grain size ranging from 0.4 to 0.8 mm
• With suction quantity control at the double suction pipe
• Sand blasting nozzle made of high-performance ceramics
• Inclusive: 3 hardened stainless steel nozzles

Multiple mediums can be used:
• Glass beads for cleaning of copper and bronze as well as polishing of stainless steel
• Glass powder for cleaning of stainless steel and natural stone or for removal of graffiti from light surfaces
• Slag (fine) for cleaning of sandstone or brick as well as removal of graffiti from dark surfaces
• Slag (coarse) removal of rust from metals or of old coatings and paintings. cleaning and grinding of concrete surfaces
• Sodium carbonate (water-soluble) cleaning of sensitive surfaces such as aluminum, glass, plastics, stainless steel
• Mineral blasting agent (sand) removal of rust from metals or of old coatings and paintings. Cleaning and grinding of concrete surfaces. Varnish removal

ST-555 Sandblaster on YouTube

SPECIFICATIONS:
• Nozzle Size: # 5.5
• Min Flow Rate: 3.0 GPM
• Max Flow Rate: 7.5 GPM
• Max Pressure: 7,250 PSI
• Max Temp: 212° F
• Hose Length: 13'
• Inlet: Male M22, Yoke/Stem: 14MM
• Weight: 4.92 lbs

Please use Nozzle Chart to determine proper nozzle size

Nozzle Chart

Suttner ST-555 Professional Sandblaster #6.5 Stainless Steel with Adjustable Sand Flow. Removes coatings from almost any surface. Ideal for cleaning of machines, technical facilities, facades and masonry. Thanks to its stainless steel body, the ST-555 features utmost pressure resistance up to a continuous operating pressure of 7,250 PSI. The three symmetrical high-pressure nozzles in the blasting head provide for a flow of the blasting agent without any deflections. This is how wear of the ceramic diffuser nozzle with TPE coating is reduced to a minimum and pulse energy of the blasting agent is used optimally

FEATURES:
• High Quality, German engineered components
• The Sandblaster ST-555 has stainless steel construction 
• The sandblaster is suitable for dust-free blasting of solids with a grain size ranging from 0.4 to 0.8 mm
• With suction quantity control at the double suction pipe
• Sand blasting nozzle made of high-performance ceramics
• Inclusive: 3 hardened stainless steel nozzles

Multiple mediums can be used:
• Glass beads for cleaning of copper and bronze as well as polishing of stainless steel
• Glass powder for cleaning of stainless steel and natural stone or for removal of graffiti from light surfaces
• Slag (fine) for cleaning of sandstone or brick as well as removal of graffiti from dark surfaces
• Slag (coarse) removal of rust from metals or of old coatings and paintings. cleaning and grinding of concrete surfaces
• Sodium carbonate (water-soluble) cleaning of sensitive surfaces such as aluminum, glass, plastics, stainless steel
• Mineral blasting agent (sand) removal of rust from metals or of old coatings and paintings. Cleaning and grinding of concrete surfaces. Varnish removal

ST-555 Sandblaster on YouTube

SPECIFICATIONS:
• Nozzle Size: # 6.5
• Min Flow Rate: 3.0 GPM
• Max Flow Rate: 7.5 GPM
• Max Pressure: 7,250 PSI
• Max Temp: 212° F
• Hose Length: 13'
• Inlet: Male M22, Yoke/Stem: 14MM
• Weight: 4.92 lbs

Please use Nozzle Chart to determine proper nozzle size

Nozzle Chart

Suttner ST-555 Professional Sandblaster #7.5 Stainless Steel with Adjustable Sand Flow. Removes coatings from almost any surface. Ideal for cleaning of machines, technical facilities, facades and masonry. Thanks to its stainless steel body, the ST-555 features utmost pressure resistance up to a continuous operating pressure of 7,250 PSI. The three symmetrical high-pressure nozzles in the blasting head provide for a flow of the blasting agent without any deflections. This is how wear of the ceramic diffuser nozzle with TPE coating is reduced to a minimum and pulse energy of the blasting agent is used optimally

FEATURES:
• High Quality, German engineered components
• The Sandblaster ST-555 has stainless steel construction 
• The sandblaster is suitable for dust-free blasting of solids with a grain size ranging from 0.4 to 0.8 mm
• With suction quantity control at the double suction pipe
• Sand blasting nozzle made of high-performance ceramics
• Inclusive: 3 hardened stainless steel nozzles

Multiple mediums can be used:
• Glass beads for cleaning of copper and bronze as well as polishing of stainless steel
• Glass powder for cleaning of stainless steel and natural stone or for removal of graffiti from light surfaces
• Slag (fine) for cleaning of sandstone or brick as well as removal of graffiti from dark surfaces
• Slag (coarse) removal of rust from metals or of old coatings and paintings. cleaning and grinding of concrete surfaces
• Sodium carbonate (water-soluble) cleaning of sensitive surfaces such as aluminum, glass, plastics, stainless steel
• Mineral blasting agent (sand) removal of rust from metals or of old coatings and paintings. Cleaning and grinding of concrete surfaces. Varnish removal

ST-555 Sandblaster on YouTube

SPECIFICATIONS:
• Nozzle Size: # 7.5
• Min Flow Rate: 3.0 GPM
• Max Flow Rate: 7.5 GPM
• Max Pressure: 7,250 PSI
• Max Temp: 212° F
• Hose Length: 13'
• Inlet: Male M22, Yoke/Stem: 14MM
• Weight: 4.92 lbs

Please use Nozzle Chart to determine proper nozzle size

Nozzle Chart

Suttner ST-559 Stainless Steel Turbo / Rotating #2.0 Nozzle. This Suttner rotating nozzle with Tungsten Carbide Nozzle & Seat is rated up to 8,700 PSI. The increased tearing action of the rotating spray is ideal for hard surface applications, such as concrete graffiti cleaning or caked mud on heavy equipment

Features
• Increases cleaning efficiency as much as 200%
• The 0° rotation creates a cleaning and tearing action
• Ideal for hard surfaces
• Tungsten Carbide nozzle and sealing seat
• Improved materials for longer life

Specifications
• Nozzle Size # 2.0
• Max PSI: 8,700
• Max Temp.: 190° F
• Inlet: 1/4" Female NPT
• NOTE: All rotating nozzles should be started pointing downward
• Weight: 1.32 lbs

Please use Nozzle Chart to determine proper nozzle size

Nozzle Chart

Suttner ST-559 Stainless Steel Turbo / Rotating #3.0 Nozzle. This Suttner rotating nozzle with Tungsten Carbide Nozzle & Seat is rated up to 8,700 PSI. The increased tearing action of the rotating spray is ideal for hard surface applications, such as concrete graffiti cleaning or caked mud on heavy equipment

Features
• Increases cleaning efficiency as much as 200%
• The 0° rotation creates a cleaning and tearing action
• Ideal for hard surfaces
• Tungsten Carbide nozzle and sealing seat
• Improved materials for longer life

Specifications
• Nozzle Size # 3.0
• Max PSI: 8,700
• Max Temp.: 190° F
• Inlet: 1/4" Female NPT
• NOTE: All rotating nozzles should be started pointing downward
• Weight: 1.32 lbs

Please use Nozzle Chart to determine proper nozzle size

Nozzle Chart

Suttner ST-559 Stainless Steel Turbo / Rotating #4.0 Nozzle. This Suttner rotating nozzle with Tungsten Carbide Nozzle & Seat is rated up to 8,700 PSI. The increased tearing action of the rotating spray is ideal for hard surface applications, such as concrete graffiti cleaning or caked mud on heavy equipment

Features
• Increases cleaning efficiency as much as 200%
• The 0° rotation creates a cleaning and tearing action
• Ideal for hard surfaces
• Tungsten Carbide nozzle and sealing seat
• Improved materials for longer life

Specifications
• Nozzle Size # 4.0
• Max PSI: 8,700
• Max Temp.: 190° F
• Inlet: 1/4" Female NPT
• NOTE: All rotating nozzles should be started pointing downward
• Weight: 1.32 lbs

Please use Nozzle Chart to determine proper nozzle size

Nozzle Chart

Suttner ST-559 Stainless Steel Turbo / Rotating #5.0 Nozzle. This Suttner rotating nozzle with Tungsten Carbide Nozzle & Seat is rated up to 8,700 PSI. The increased tearing action of the rotating spray is ideal for hard surface applications, such as concrete graffiti cleaning or caked mud on heavy equipment

Features
• Increases cleaning efficiency as much as 200%
• The 0° rotation creates a cleaning and tearing action
• Ideal for hard surfaces
• Tungsten Carbide nozzle and sealing seat
• Improved materials for longer life

Specifications
• Nozzle Size # 5.0
• Max PSI: 8,700
• Max Temp.: 190° F
• Inlet: 1/4" Female NPT
• NOTE: All rotating nozzles should be started pointing downward
• Weight: 1.32 lbs

Please use Nozzle Chart to determine proper nozzle size

Nozzle Chart

Suttner ST-559 Stainless Steel Turbo / Rotating #6.0 Nozzle. This Suttner rotating nozzle with Tungsten Carbide Nozzle & Seat is rated up to 8,700 PSI. The increased tearing action of the rotating spray is ideal for hard surface applications, such as concrete graffiti cleaning or caked mud on heavy equipment

Features
• Increases cleaning efficiency as much as 200%
• The 0° rotation creates a cleaning and tearing action
• Ideal for hard surfaces
• Tungsten Carbide nozzle and sealing seat
• Improved materials for longer life

Specifications
• Nozzle Size # 6.0
• Max PSI: 8,700
• Max Temp.: 190° F
• Inlet: 1/4" Female NPT
• NOTE: All rotating nozzles should be started pointing downward
• Weight: 1.32 lbs

Please use Nozzle Chart to determine proper nozzle size

Nozzle Chart

Features
• High Quality, German engineered components
• Simply turn over the complete assembly or swivel lance and you have access to two different nozzles
• Water sprays through one nozzle port at a time since a stainless steel ball covers the opposite port
• Nozzle housing is made of an impact resistant plastic, manufactured of corrosion resistant material
• Spray depends on 2 nozzles used

Specifications
• Max Pressure: 3,600 PSI
• Max Flow: 8 GPM
• Max Temp: 300° F.
• Inlet: 1/4" Female NPT
• Outlets (2): 1/4" Female NPT
• Note: 1/4” MPT Nozzles not included
• Weight: 0.51 lb

Suttner ST-58 Change Over Valve 5,000 PSI 1/4" FPT. Suttner ST58 change-over design allows you to switch between lances and nozzles with a twist

Features
• Stainless steel
• No roll over nozzle
• Corrosive resistant

Specifications
• Max Pressure: 5,000 PSI
• Max Temp: 200° F.
• Inlet: 1/4" Female NPT
• Outlets (2): 1/4" Female NPT
• Weight: 0.85 lbs

Suttner ST-6 Any Position Flow Switch. Mounts in any position and spring assisted brass magnet configuration

Features:
• Can be mounted horizontal or vertical
• Reed switch encased in protective vacuum sealed glass tube eliminating exposure to corrosive cleaning chemicals
• Mounts further downstream in pumping system than traditional vacuum switches, thereby minimizing potential leak points that can cause vacuum switches to close
• Easy reed switch replacement
• Most proven and reliable flow switches in the industry

Specifications:
• Max. Pressure: 5,070 PSI
• Min. Pressure: 75 PSI
• Max. Flow Rate: 8.0 GPM
• Min. Flow Rate: 1 GPM
• Contact: 1 A - 250 V
• Max: Fluid Temperature: 176° F
• Cable Length: 47.0”
• Inlet & Outlet: 3/8” MPT
• Housing: Brass
• Replaces 200006540
• Weight: 0.80 lbs

Features
• High Quality, German engineered components
• Horizontal flow-through design
• Forged brass housing for maximum strength
• Unitized valve for easy repair
• Stainless steel spring, needle, ball, and seat for chemical resistance
• Special heat and chemical resistant seals for optimum performance even in the harshest of environments

Specifications
• Max Pressure: 4,000 PSI
• Max Flow: 12.0 GPM
• Max Temp: 320° F.
• Inlet: 3/8" Female NPT
• Outlet: 1/4" Female NPT
• Weight: 1.16 lb

Suttner ST-601C Inline Chemical Resistant Spray Gun 4,000 PSI with Ceramic Ball. Ideal for cleaning vertical and overhead surfaces. Perfect for washing tractors, trailers, siding, windows, eaves, etc.

Features
• High Quality, German engineered components
• Superior Chemical Resistant
• Horizontal flow-through design
• Heavy duty, impact-resistant trigger guard
• Forged brass housing for maximum strength
• Unitized valve allows for higher temps and longer life
• Ceramic ball in valve is highly resistant against nearly all soaps and acids

Specifications
• Max Pressure: 4,000 PSI
• Max Flow: 12.0 GPM
• Max Temp: 300° F.
• Inlet: 3/8" Female NPT
• Outlet: 1/4" Female NPT
• Weight: 1.16 lb

Suttner ST-60F Brass Injector, Up to 5.0 Orifice, 3/8" M x 3/8" F. The ST-60F is a downstream chemical injector that relies on a pressure drop that is created by using a larger orifice spray nozzle

Features
• Siphon rate approximately 10:1
• Stainless steel spring and ball
• Fixed flow rate for accuracy
• Forged brass housing

Specifications
• Orifice Size: Up to 5
• Injector Size: 1.6 mm
• Max Pressure: 3,600 PSI
• Max Temp: 140° F.
• Inlet: 3/8” Male NPT
• Outlet: 3/8” Female NPT
• Hose Barb: 1/4” ID hose
• Weight: 0.20 lb

Suttner ST-60F Brass Injector, Up to 6.5 Orifice, 3/8" M x 3/8" F. The ST-60F is a downstream chemical injector that relies on a pressure drop that is created by using a larger orifice spray nozzle

Features
• Siphon rate approximately 10:1
• Stainless steel spring and ball
• Fixed flow rate for accuracy
• Forged brass housing

Specifications
• Orifice Size: Up to 6.5
• Injector Size: 1.8 mm
• Max Pressure: 3,600 PSI
• Max Temp: 140° F.
• Inlet: 3/8” Male NPT
• Outlet: 3/8” Female NPT
• Hose Barb: 1/4” ID hose
• Weight: 0.20 lb

Features:
• Draw Rate:0 - 11%
• Connects to chemical inlet barb without any special tools needed
• Made of glass filled poly-material, extremely corrosive resistant

Specifications:
• Flow Rate: 0.27 GPM
• Max Temperature: 140° F
• Weight: 0.06 lbs

Features:
• Designed to introduce detergents into the water system upstream from the pump at high pressure
• The "on-off" plunger is then used to control the injection
• Easily connects to inlet of pump at garden hose connection
• Adjustable chemical flow
• Chemical strainer and 4’ PVC tubing included
• Choose size based on flow rate of your pressure washer

See the ST-64 in action on YouTube

Specifications:
• Size: 1.5 to 4.0 GPM flow rate
• Max Temperature: 140° F
• Inlet: 1/2" Female NPT
• Outlet: 1/2" Male NPT
• Optional ST-61 chemical metering valve adjusts from off to full flow
• Weight: 0.80 lb

Features:
• Designed to introduce detergents into the water system upstream from the pump at high pressure
• The "on-off" plunger is then used to control the injection
• Easily connects to inlet of pump at garden hose connection
• Adjustable chemical flow
• Chemical strainer and 4’ PVC tubing included
• Choose size based on flow rate of your pressure washer

See the ST-64 in action on YouTube

Specifications:
• Size: 1.5 to 4.0 GPM flow rate
• Max Temperature: 140° F
• Inlet: 3/4" FGH (female garden hose)
• Outlet: 3/4" MGH (male garden hose)
• Optional ST-61 chemical metering valve adjusts from off to full flow
• Weight: 0.78 lb

Features:
• Designed to introduce detergents into the water system upstream from the pump at high pressure
• The "on-off" plunger is then used to control the injection
• Easily connects to inlet of pump at garden hose connection
• Adjustable chemical flow
• Chemical strainer and 4’ PVC tubing included
• Choose size based on flow rate of your pressure washer

See the ST-64 in action on YouTube

Specifications:
• Size: 4.0 to 7.0 GPM flow rate
• Max Temperature: 140° F
• Inlet: 1/2" Female NPT
• Outlet: 1/2" Male NPT
• Optional ST-61 chemical metering valve adjusts from off to full flow
• Weight: 0.80 lb

Features:
• Designed to introduce detergents into the water system upstream from the pump at high pressure
• The "on-off" plunger is then used to control the injection
• Easily connects to inlet of pump at garden hose connection
• Adjustable chemical flow
• Chemical strainer and 4’ PVC tubing included
• Choose size based on flow rate of your pressure washer

See the ST-64 in action on YouTube

Specifications:
• Size: 4.0 to 7.0 GPM flow rate
• Max Temperature: 140° F
• Inlet: 3/4" FGH (female garden hose)
• Outlet: 3/4" MGH (male garden hose)
• Optional ST-61 chemical metering valve adjusts from off to full flow
• Weight: 0.78 lb

Features:
• Simply turn the knob to the desired side and setting on the easy to read legend plate
• Industry standard for panel mount chemical metering valves
• Volume flow is adjustable from 0 up to .27 GPM

Specifications:
• Draw Rate: 0 - 10%
• Flow Rate: 0.27 GPM
• Max Temperature: 140° F
• Weight: 0.16 lbs

Features:
• Can be mounted horizontal or vertical
• Micro-switch replaces reed switch for better reliability and water protection
• Easy to install
• Resistant against shock and vibration
• IP 65 rated-water and dust proof
• Can be wired normally open or normally closed

Specifications:
• Switch Point: 0.3 GPM
• Max. Pressure: 5,000 PS
• Max. Flow Rate: 12 GPM
• Max Voltage: 250 V
• Max Current: 10.1 Amps
• Max: Fluid Temperature: 176° F
• Cable Length: 47.0”
• Inlet & Outlet: 3/8” FNPT
• Weight: 0.80 lbs

Features:
• Can be mounted horizontal or vertical
• Micro-switch replaces reed switch for better reliability and water protection
• Easy to install
• Resistant against shock and vibration
• IP 65 rated-water and dust proof
• Can be wired normally open or normally closed

Specifications:
• Switch Point: 1.2 GPM
• Max. Pressure: 5,000 PS
• Max. Flow Rate: 12 GPM
• Max Voltage: 250 V
• Max Current: 10.1 Amps
• Max: Fluid Temperature: 176° F
• Cable Length: 47.0”
• Inlet & Outlet: 3/8” FNPT
• Weight: 0.80 lbs

Suttner ST-7.1 Pressure Switch, 360 Switching Point (Red), 1/4" M 4,350 PSI

Features:
• IP 65 protection class
• Simultaneous N/O and N/C connection is possible
• The design of the micro switch allows comparably high inrush current (20 Amps N/C, 15 Amps N/O)
• The electrical capacity of the switch is 10.1 Amps (resistive load)
• No ingress of towing water into the environment of the microswitch possible

Suttner ST-7.1 Data Sheet

Specifications:
• Switch Point: 360 PSI (Red)
• Max. Pressure: 4,350 PS
• Voltage: 10.1 A - 250 VAC
• Max: Fluid Temperature: 194° F
• Cable Length: 37.4”
• Thread: 1/4” Male
• Material: Brass / plastic
• Protection Class” IP 65
• Weight: 0.65 lbs

Suttner ST-7.1 Pressure Switch, 580 Switching Point (Black), 1/4" M 4,350 PSI

Features:
• IP 65 protection class
• Simultaneous N/O and N/C connection is possible
• The design of the micro switch allows comparably high inrush current (20 Amps N/C, 15 Amps N/O)
• The electrical capacity of the switch is 10.1 Amps (resistive load)
• No ingress of towing water into the environment of the microswitch possible

Suttner ST-7.1 Data Sheet

Specifications:
• Switch Point: 580 PSI (Black)
• Max. Pressure: 4,350 PS
• Voltage: 10.1 A - 250 VAC
• Max: Fluid Temperature: 194° F
• Cable Length: 37.4”
• Thread: 1/4” Male
• Material: Brass / plastic
• Protection Class” IP 65
• Weight: 0.65 lbs

Suttner ST-72 Stainless Steel 23.5” Vented Grip Foam Lance with #2.0 mm (Green) Air Injector Nozzle and 1/4" M Inlet. In conjunction with a spray gun and Suttner foam injector, allows cleaning agents or disinfectants to be applied evenly over a large surface. Stainless steel construction

Features
• Thick foam is produced when air flows through vented injector housing and mixes with water and chemical stream
• Wet foam allows more efficient use of chemical
• More durable than conventional foamers

Specifications
• Air Injector Nozzle Size: 2.0 mm (Green)
• Max Pressure: 3,625 PSI
• Length: 23.5”
• Max Temp: 176° F.
• Inlet: 1/4" Male
• Note: Suttner ST-160, ST-160M or St-164 Chemical or Foam injector required and is not included
• Weight: 1.95 lb

Please use Nozzle Chart to determine proper Spray Nozzle Size

Nozzle Chart

Use Spray Nozzle Size and Foam Lance Chart to determine correct Air Injector Nozzle Size to use

Foam Lance Chart

Suttner ST-72 Stainless Steel 23.5” Vented Grip Foam Lance with #2.3 mm (Yellow) Air Injector Nozzle and 1/4" M Inlet. In conjunction with a spray gun and Suttner foam injector, allows cleaning agents or disinfectants to be applied evenly over a large surface. Stainless steel construction

Features
• Thick foam is produced when air flows through vented injector housing and mixes with water and chemical stream
• Wet foam allows more efficient use of chemical
• More durable than conventional foamers

Specifications
• Air Injector Nozzle Size: 2.3 mm (Yellow)
• Max Pressure: 3,625 PSI
• Length: 23.5”
• Max Temp: 176° F.
• Inlet: 1/4" Male
• Note: Suttner ST-160, ST-160M or St-164 Chemical or Foam injector required and is not included
• Weight: 1.95 lb

Please use Nozzle Chart to determine proper Spray Nozzle Size

Nozzle Chart

Use Spray Nozzle Size and Foam Lance Chart to determine correct Air Injector Nozzle Size to use

Foam Lance Chart

Suttner ST-72 Stainless Steel 23.5” Vented Grip Foam Lance with #3.0 mm (Blue) Air Injector Nozzle and 1/4" M Inlet. In conjunction with a spray gun and Suttner foam injector, allows cleaning agents or disinfectants to be applied evenly over a large surface. Stainless steel construction

Features
• Thick foam is produced when air flows through vented injector housing and mixes with water and chemical stream
• Wet foam allows more efficient use of chemical
• More durable than conventional foamers

Specifications
• Air Injector Nozzle Size: 3.0 mm (Blue)
• Max Pressure: 3,625 PSI
• Length: 23.5”
• Max Temp: 176° F.
• Inlet: 1/4" Male
• Note: Suttner ST-160, ST-160M or St-164 Chemical or Foam injector required and is not included
• Weight: 1.95 lb

Please use Nozzle Chart to determine proper Spray Nozzle Size

Nozzle Chart

Use Spray Nozzle Size and Foam Lance Chart to determine correct Air Injector Nozzle Size to use

Foam Lance Chart

Suttner ST-72 Stainless Steel 23.5” Vented Grip Foam Lance with #3.2 mm (Red) Air Injector Nozzle and 1/4" M Inlet. In conjunction with a spray gun and Suttner foam injector, allows cleaning agents or disinfectants to be applied evenly over a large surface. Stainless steel construction

Features
• Thick foam is produced when air flows through vented injector housing and mixes with water and chemical stream
• Wet foam allows more efficient use of chemical
• More durable than conventional foamers

Specifications
• Air Injector Nozzle Size: 3.2 mm (Red)
• Max Pressure: 3,625 PSI
• Length: 23.5”
• Max Temp: 176° F.
• Inlet: 1/4" Male
• Note: Suttner ST-160, ST-160M or St-164 Chemical or Foam injector required and is not included
• Weight: 1.95 lb

Please use Nozzle Chart to determine proper Spray Nozzle Size

Nozzle Chart

Use Spray Nozzle Size and Foam Lance Chart to determine correct Air Injector Nozzle Size to use

Foam Lance Chart

Suttner ST-72 Stainless Steel 47.25” Vented Grip Foam Lance with #2.0 mm (Green) Air Injector Nozzle and 1/4" M Inlet. In conjunction with a spray gun and Suttner foam injector, allows cleaning agents or disinfectants to be applied evenly over a large surface. Stainless steel construction

Features
• Thick foam is produced when air flows through vented injector housing and mixes with water and chemical stream
• Wet foam allows more efficient use of chemical
• More durable than conventional foamers

Specifications
• Air Injector Nozzle Size: 2.0 mm (Green)
• Max Pressure: 3,625 PSI
• Length: 47.25”
• Max Temp: 176° F.
• Inlet: 1/4" Male
• Note: Suttner ST-160, ST-160M or St-164 Chemical or Foam injector required and is not included
• Weight: 2.45 lb

Please use Nozzle Chart to determine proper Spray Nozzle Size

Nozzle Chart

Use Spray Nozzle Size and Foam Lance Chart to determine correct Air Injector Nozzle Size to use

Foam Lance Chart

Suttner ST-72 Stainless Steel 47.25” Vented Grip Foam Lance with #2.3 mm (Yellow) Air Injector Nozzle and 1/4" M Inlet. In conjunction with a spray gun and Suttner foam injector, allows cleaning agents or disinfectants to be applied evenly over a large surface. Stainless steel construction

Features
• Thick foam is produced when air flows through vented injector housing and mixes with water and chemical stream
• Wet foam allows more efficient use of chemical
• More durable than conventional foamers

Specifications
• Air Injector Nozzle Size: 2.3 mm (Yellow)
• Max Pressure: 3,625 PSI
• Length: 47.25”
• Max Temp: 176° F.
• Inlet: 1/4" Male
• Note: Suttner ST-160, ST-160M or St-164 Chemical or Foam injector required and is not included
• Weight: 2.45 lb

Please use Nozzle Chart to determine proper Spray Nozzle Size

Nozzle Chart

Use Spray Nozzle Size and Foam Lance Chart to determine correct Air Injector Nozzle Size to use

Foam Lance Chart

Suttner ST-72 Stainless Steel 47.25” Vented Grip Foam Lance with #3.0 mm (Blue) Air Injector Nozzle and 1/4" M Inlet. In conjunction with a spray gun and Suttner foam injector, allows cleaning agents or disinfectants to be applied evenly over a large surface. Stainless steel construction

Features
• Thick foam is produced when air flows through vented injector housing and mixes with water and chemical stream
• Wet foam allows more efficient use of chemical
• More durable than conventional foamers

Specifications
• Air Injector Nozzle Size: 3.0 mm (Blue)
• Max Pressure: 3,625 PSI
• Length: 47.25”
• Max Temp: 176° F.
• Inlet: 1/4" Male
• Note: Suttner ST-160, ST-160M or St-164 Chemical or Foam injector required and is not included
• Weight: 2.45 lb

Please use Nozzle Chart to determine proper Spray Nozzle Size

Nozzle Chart

Use Spray Nozzle Size and Foam Lance Chart to determine correct Air Injector Nozzle Size to use

Foam Lance Chart

Suttner ST-72 Stainless Steel 47.25” Vented Grip Foam Lance with #3.2 mm (Red) Air Injector Nozzle and 1/4" M Inlet. In conjunction with a spray gun and Suttner foam injector, allows cleaning agents or disinfectants to be applied evenly over a large surface. Stainless steel construction

Features
• Thick foam is produced when air flows through vented injector housing and mixes with water and chemical stream
• Wet foam allows more efficient use of chemical
• More durable than conventional foamers

Specifications
• Air Injector Nozzle Size: 3.2 mm (Red)
• Max Pressure: 3,625 PSI
• Length: 47.25”
• Max Temp: 176° F.
• Inlet: 1/4" Male
• Note: Suttner ST-160, ST-160M or St-164 Chemical or Foam injector required and is not included
• Weight: 2.45 lb

Please use Nozzle Chart to determine proper Spray Nozzle Size

Nozzle Chart

Use Spray Nozzle Size and Foam Lance Chart to determine correct Air Injector Nozzle Size to use

Foam Lance Chart

Suttner ST-72F Stainless Steel Food Grade 23.5” Vented Grip Foam Lance with #2.0 mm (Green) Air Injector Nozzle and 1/4" M Inlet. In conjunction with a spray gun and Suttner foam injector, allows cleaning agents or disinfectants to be applied evenly over a large surface. Stainless steel construction

Features
• Thick foam is produced when air flows through vented injector housing and mixes with water and chemical stream
• Wet foam allows more efficient use of chemical
• More durable than conventional foamers
• Food grade - Stainless steel and plastic intended to come into contact with foodstuffs

Specifications
• Air Injector Nozzle Size: 2.0 mm (Green)
• Max Pressure: 3,625 PSI
• Length: 23.5”
• Max Temp: 176° F.
• Inlet: 1/4" Male
• Note: Suttner ST-160, ST-160M or St-164 Chemical or Foam injector required and is not included
• Weight: 1.50 lb

Please use Nozzle Chart to determine proper Spray Nozzle Size

Nozzle Chart

Use Spray Nozzle Size and Foam Lance Chart to determine correct Air Injector Nozzle Size to use

Foam Lance Chart

Suttner ST-72F Stainless Steel Food Grade 23.5” Vented Grip Foam Lance with #2.3 mm (Yellow) Air Injector Nozzle and 1/4" M Inlet. In conjunction with a spray gun and Suttner foam injector, allows cleaning agents or disinfectants to be applied evenly over a large surface. Stainless steel construction

Features
• Thick foam is produced when air flows through vented injector housing and mixes with water and chemical stream
• Wet foam allows more efficient use of chemical
• More durable than conventional foamers
• Food grade - Stainless steel and plastic intended to come into contact with foodstuffs

Specifications
• Air Injector Nozzle Size: 2.3 mm (Yellow)
• Max Pressure: 3,625 PSI
• Length: 23.5”
• Max Temp: 176° F.
• Inlet: 1/4" Male
• Note: Suttner ST-160, ST-160M or St-164 Chemical or Foam injector required and is not included
• Weight: 1.50 lb

Please use Nozzle Chart to determine proper Spray Nozzle Size

Nozzle Chart

Use Spray Nozzle Size and Foam Lance Chart to determine correct Air Injector Nozzle Size to use

Foam Lance Chart

Suttner ST-72F Stainless Steel Food Grade 23.5” Vented Grip Foam Lance with #3.0 mm (Blue) Air Injector Nozzle and 1/4" M Inlet. In conjunction with a spray gun and Suttner foam injector, allows cleaning agents or disinfectants to be applied evenly over a large surface. Stainless steel construction

Features
• Thick foam is produced when air flows through vented injector housing and mixes with water and chemical stream
• Wet foam allows more efficient use of chemical
• More durable than conventional foamers
• Food grade - Stainless steel and plastic intended to come into contact with foodstuffs

Specifications
• Air Injector Nozzle Size: 3.0 mm (Blue)
• Max Pressure: 3,625 PSI
• Length: 23.5”
• Max Temp: 176° F.
• Inlet: 1/4" Male
• Note: Suttner ST-160, ST-160M or St-164 Chemical or Foam injector required and is not included
• Weight: 1.50 lb

Please use Nozzle Chart to determine proper Spray Nozzle Size

Nozzle Chart

Use Spray Nozzle Size and Foam Lance Chart to determine correct Air Injector Nozzle Size to use

Foam Lance Chart

Suttner ST-73.2 Foamer with 32 oz. Bottle, Stainless Steel Integrated Injector, 1/4" F Inlet. Convenient and portable for more effective foam cleaning for Industry, Agriculture, Automotive/Fleet and Institutional applications! By turning an adjustable grip handle the concentration of foaming agent in the water can be adjusted. Our latest innovation realizes an ideal mixing of air and cleaning agent, thus succeeding an ideal foam result

Features
• 5 Position metering valve for chemical draw
• Sometimes, less is more! This version of our foam injector lance is equipped with a mesh strainer instead of a foam pad. Not being equipped with a foam pad contributes to the fact that blockages can be almost ruled out
• Adjustable nozzle - with a simple twist you can change from a horizontal spray to a vertical spray
• A completely stainless steel and non-corrosive injector unit
• The highest grade of chemical resistance
• Easy to fill wide mouth bottle with fill markings
• Integrated injector (no additional injector required)

Concentration Rates
• Setting 1: 2 - 2.5%
• Setting 2: 4 - 4.5%
• Setting 3: 5 - 5.5%
• Setting 4: 6.5 - 7%
• Setting 5: 7.5 - 8%

See ST-73.2 in action on YouTube

Specifications
• Pressure: 1,000 - 4,350 PSI
• Flow Rate: 1.32 – 5.2 GPM
• Max Temp: 100° F.
• Inlet: 1/4" Female
• Bottle: 32 oz
• Weight: 1.10 lb

Suttner ST-73.2 Foamer with 64 oz. Bottle, Stainless Steel Integrated Injector, 1/4" F Inlet. Convenient and portable for more effective foam cleaning for Industry, Agriculture, Automotive/Fleet and Institutional applications! By turning an adjustable grip handle the concentration of foaming agent in the water can be adjusted. Our latest innovation realizes an ideal mixing of air and cleaning agent, thus succeeding an ideal foam result

Features
• 5 Position metering valve for chemical draw
• Sometimes, less is more! This version of our foam injector lance is equipped with a mesh strainer instead of a foam pad. Not being equipped with a foam pad contributes to the fact that blockages can be almost ruled out
• Adjustable nozzle - with a simple twist you can change from a horizontal spray to a vertical spray
• A completely stainless steel and non-corrosive injector unit
• The highest grade of chemical resistance
• Easy to fill wide mouth bottle with fill markings
• Integrated injector (no additional injector required)

Concentration Rates
• Setting 1: 2 - 2.5%
• Setting 2: 4 - 4.5%
• Setting 3: 5 - 5.5%
• Setting 4: 6.5 - 7%
• Setting 5: 7.5 - 8%

See ST-73.2 in action on YouTube

See ST-73 in action on YouTube

Specifications
• Pressure: 1,000 - 4,350 PSI
• Flow Rate: 1.32 – 5.2 GPM
• Max Temp: 100° F.
• Inlet: 1/4" Female
• Bottle: 64 oz
• Weight: 1.20 lb

Suttner ST-740 Stainless Steel Screw Coupling, 1/2" M x M24-15MM F 10,150 PSI

Features:
• Stainless steel construction for chemical & food applications
• Ideal for connections that have to be changed
• HNBR O-Ring

Specifications:
• Max. Pressure: 10,150 PSI
• Max. Temp: 300°
• Body Material: Stainless steel
• Size: 1/2” MBSP x M24
• Yoke: M15
• Weight: 0.35 lbs

Suttner ST-740 Stainless Steel Screw Coupling, 1/4" M x M24-15MM F 10,150 PSI

Features:
• Stainless steel construction for chemical & food applications
• Ideal for connections that have to be changed
• HNBR O-Ring

Specifications:
• Max. Pressure: 10,150 PSI
• Max. Temp: 300°
• Body Material: Stainless steel
• Size: 1/4” MBSP x M24
• Yoke: M15
• Weight: 0.35 lbs

Suttner ST-740 Stainless Steel Screw Coupling, 3/8" F x M24-15MM F 10,150 PSI

Features:
• Stainless steel construction for chemical & food applications
• Ideal for connections that have to be changed
• HNBR O-Ring

Specifications:
• Max. Pressure: 10,150 PSI
• Max. Temp: 300°
• Body Material: Stainless steel
• Size: 3/8” FBSP x M24
• Yoke: M15
• Weight: 0.35 lbs

Suttner ST-740 Stainless Steel Screw Coupling, 3/8" M x M24-15MM F 10,150 PSI

Features:
• Stainless steel construction for chemical & food applications
• Ideal for connections that have to be changed
• HNBR O-Ring

Specifications:
• Max. Pressure: 10,150 PSI
• Max. Temp: 300°
• Body Material: Stainless steel
• Size: 3/8” MBSP x M24
• Yoke: M15
• Weight: 0.35 lbs

Suttner ST-741 Stainless Steel Screw Nipple, 1/2" M x M24-15MM MF 10,150 PSI

Features:
• Stainless steel construction for chemical & food applications
• Ideal for connections that have to be changed
• EPDM O-Ring

Specifications:
• Max. Pressure: 10,150 PSI
• Max. Temp: 300°
• Material: Stainless steel & EPDM
• Size: 1/2” MBSP x M24
• Yoke: M15
• Weight: 0.16 lbs

Suttner ST-741 Stainless Steel Screw Nipple, 1/4" M x M24-15MM MF 10,150 PSI

Features:
• Stainless steel construction for chemical & food applications
• Ideal for connections that have to be changed
• EPDM O-Ring

Specifications:
• Max. Pressure: 10,150 PSI
• Max. Temp: 300°
• Material: Stainless steel & EPDM
• Size: 1/4” MBSP x M24
• Yoke: M15
• Weight: 0.16 lbs

Suttner ST-741 Stainless Steel Screw Nipple, 3/8" F x M24-15MM MF 10,150 PSI

Features:
• Stainless steel construction for chemical & food applications
• Ideal for connections that have to be changed
• EPDM O-Ring

Specifications:
• Max. Pressure: 10,150 PSI
• Max. Temp: 300°
• Material: Stainless steel & EPDM
• Size: 3/8” FBSP x M24
• Yoke: M15
• Weight: 0.16 lbs

Suttner ST-741 Stainless Steel Screw Nipple, 3/8" M x M24-15MM MF 10,150 PSI

Features:
• Stainless steel construction for chemical & food applications
• Ideal for connections that have to be changed
• EPDM O-Ring

Specifications:
• Max. Pressure: 10,150 PSI
• Max. Temp: 300°
• Material: Stainless steel & EPDM
• Size: 3/8” MBSP x M24
• Yoke: M15
• Weight: 0.16 lbs

Suttner ST-75 Brass Foam Head 4,000 PSI with #10.0 Air Injector Nozzle and 1/4" F Inlet. The ST-75 produces thick foam for an easy and safe application and to save on chemical usage by reducing splash and drift of chemicals

Features
• By means of the foam head ST-75 different foam applications are possible as the air injector nozzle is easily exchangeable and adaptable
• The flat spray nozzle can be infinitely adapted from the vertical position to the horizontal one
• The maximum flow is dependent on the chosen nozzle size
• By means of the integrated air injector in the foam head the air is sucked in on the face side
• Independent of the length of the lance a constant foam quality is guaranteed
• The spraying result is especially even as a high quality foam nozzle insert is used

ST-75 with ST-160 Chemical Injector on YouTube

Specifications
• Air Injector Nozzle Size: 10.0
• Max Pressure: 4,000 PSI
• Flow Rate: 1 - 6 GPM
• Max Temp: 212° F.
• Inlet: 1/4" Female
• Note: Suttner ST-160, ST-160M or St-164 Chemical or Foam injector required and is not included
• Weight: 0.31 lb

Please use Nozzle Chart to determine proper Spray Nozzle Size

Nozzle Chart

Use Spray Nozzle Size and Foam Nozzle Chart to determine correct Foam Nozzle to use

Foam Nozzle Chart

Suttner ST-75 Brass Foam Head 4,000 PSI with #13.0 Air Injector Nozzle and 1/4" F Inlet. The ST-75 produces thick foam for an easy and safe application and to save on chemical usage by reducing splash and drift of chemicals

Features
• By means of the foam head ST-75 different foam applications are possible as the air injector nozzle is easily exchangeable and adaptable
• The flat spray nozzle can be infinitely adapted from the vertical position to the horizontal one
• The maximum flow is dependent on the chosen nozzle size
• By means of the integrated air injector in the foam head the air is sucked in on the face side
• Independent of the length of the lance a constant foam quality is guaranteed
• The spraying result is especially even as a high quality foam nozzle insert is used

ST-75 with ST-160 Chemical Injector on YouTube

Specifications
• Air Injector Nozzle Size: 13.0
• Max Pressure: 4,000 PSI
• Flow Rate: 1 - 6 GPM
• Max Temp: 212° F.
• Inlet: 1/4" Female
• Note: Suttner ST-160, ST-160M or St-164 Chemical or Foam injector required and is not included
• Weight: 0.31 lb

Please use Nozzle Chart to determine proper Spray Nozzle Size

Nozzle Chart

Use Spray Nozzle Size and Foam Nozzle Chart to determine correct Foam Nozzle to use

Foam Nozzle Chart

Suttner ST-75 Brass Foam Head 4,000 PSI with #15.0 Air Injector Nozzle and 1/4" F Inlet. The ST-75 produces thick foam for an easy and safe application and to save on chemical usage by reducing splash and drift of chemicals

Features
• By means of the foam head ST-75 different foam applications are possible as the air injector nozzle is easily exchangeable and adaptable
• The flat spray nozzle can be infinitely adapted from the vertical position to the horizontal one
• The maximum flow is dependent on the chosen nozzle size
• By means of the integrated air injector in the foam head the air is sucked in on the face side
• Independent of the length of the lance a constant foam quality is guaranteed
• The spraying result is especially even as a high quality foam nozzle insert is used

ST-75 with ST-160 Chemical Injector on YouTube

Specifications
• Air Injector Nozzle Size: 15.0
• Max Pressure: 4,000 PSI
• Flow Rate: 1 - 6 GPM
• Max Temp: 212° F.
• Inlet: 1/4" Female
• Note: Suttner ST-160, ST-160M or St-164 Chemical or Foam injector required and is not included
• Weight: 0.31 lb

Please use Nozzle Chart to determine proper Spray Nozzle Size

Nozzle Chart

Use Spray Nozzle Size and Foam Nozzle Chart to determine correct Foam Nozzle to use

Foam Nozzle Chart

Suttner ST-75 Brass Foam Head 4,000 PSI with #3.0 Air Injector Nozzle and 1/4" F Inlet. The ST-75 produces thick foam for an easy and safe application and to save on chemical usage by reducing splash and drift of chemicals

Features
• By means of the foam head ST-75 different foam applications are possible as the air injector nozzle is easily exchangeable and adaptable
• The flat spray nozzle can be infinitely adapted from the vertical position to the horizontal one
• The maximum flow is dependent on the chosen nozzle size
• By means of the integrated air injector in the foam head the air is sucked in on the face side
• Independent of the length of the lance a constant foam quality is guaranteed
• The spraying result is especially even as a high quality foam nozzle insert is used

ST-75 with ST-160 Chemical Injector on YouTube

Specifications
• Air Injector Nozzle Size: 3.0
• Max Pressure: 4,000 PSI
• Flow Rate: 1 - 6 GPM
• Max Temp: 212° F.
• Inlet: 1/4" Female
• Note: Suttner ST-160, ST-160M or St-164 Chemical or Foam injector required and is not included
• Weight: 0.31 lb

Please use Nozzle Chart to determine proper Spray Nozzle Size

Nozzle Chart

Use Spray Nozzle Size and Foam Nozzle Chart to determine correct Foam Nozzle to use

Foam Nozzle Chart

Suttner ST-75 Brass Foam Head 4,000 PSI with #4.0 Air Injector Nozzle and 1/4" F Inlet. The ST-75 produces thick foam for an easy and safe application and to save on chemical usage by reducing splash and drift of chemicals

Features
• By means of the foam head ST-75 different foam applications are possible as the air injector nozzle is easily exchangeable and adaptable
• The flat spray nozzle can be infinitely adapted from the vertical position to the horizontal one
• The maximum flow is dependent on the chosen nozzle size
• By means of the integrated air injector in the foam head the air is sucked in on the face side
• Independent of the length of the lance a constant foam quality is guaranteed
• The spraying result is especially even as a high quality foam nozzle insert is used

ST-75 with ST-160 Chemical Injector on YouTube

Specifications
• Air Injector Nozzle Size: 4.0
• Max Pressure: 4,000 PSI
• Flow Rate: 1 - 6 GPM
• Max Temp: 212° F.
• Inlet: 1/4" Female
• Note: Suttner ST-160, ST-160M or St-164 Chemical or Foam injector required and is not included
• Weight: 0.31 lb

Please use Nozzle Chart to determine proper Spray Nozzle Size

Nozzle Chart

Use Spray Nozzle Size and Foam Nozzle Chart to determine correct Foam Nozzle to use

Foam Nozzle Chart

Suttner ST-75 Brass Foam Head 4,000 PSI with #5.0 Air Injector Nozzle and 1/4" F Inlet. The ST-75 produces thick foam for an easy and safe application and to save on chemical usage by reducing splash and drift of chemicals

Features
• By means of the foam head ST-75 different foam applications are possible as the air injector nozzle is easily exchangeable and adaptable
• The flat spray nozzle can be infinitely adapted from the vertical position to the horizontal one
• The maximum flow is dependent on the chosen nozzle size
• By means of the integrated air injector in the foam head the air is sucked in on the face side
• Independent of the length of the lance a constant foam quality is guaranteed
• The spraying result is especially even as a high quality foam nozzle insert is used

ST-75 with ST-160 Chemical Injector on YouTube

Specifications
• Air Injector Nozzle Size: 5.0
• Max Pressure: 4,000 PSI
• Flow Rate: 1 - 6 GPM
• Max Temp: 212° F.
• Inlet: 1/4" Female
• Note: Suttner ST-160, ST-160M or St-164 Chemical or Foam injector required and is not included
• Weight: 0.31 lb

Please use Nozzle Chart to determine proper Spray Nozzle Size

Nozzle Chart

Use Spray Nozzle Size and Foam Nozzle Chart to determine correct Foam Nozzle to use

Foam Nozzle Chart

Suttner ST-75 Brass Foam Head 4,000 PSI with #6.5 Air Injector Nozzle and 1/4" F Inlet. The ST-75 produces thick foam for an easy and safe application and to save on chemical usage by reducing splash and drift of chemicals

Features
• By means of the foam head ST-75 different foam applications are possible as the air injector nozzle is easily exchangeable and adaptable
• The flat spray nozzle can be infinitely adapted from the vertical position to the horizontal one
• The maximum flow is dependent on the chosen nozzle size
• By means of the integrated air injector in the foam head the air is sucked in on the face side
• Independent of the length of the lance a constant foam quality is guaranteed
• The spraying result is especially even as a high quality foam nozzle insert is used

ST-75 with ST-160 Chemical Injector on YouTube

Specifications
• Air Injector Nozzle Size: 6.5
• Max Pressure: 4,000 PSI
• Flow Rate: 1 - 6 GPM
• Max Temp: 212° F.
• Inlet: 1/4" Female
• Note: Suttner ST-160, ST-160M or St-164 Chemical or Foam injector required and is not included
• Weight: 0.31 lb

Please use Nozzle Chart to determine proper Spray Nozzle Size

Nozzle Chart

Use Spray Nozzle Size and Foam Nozzle Chart to determine correct Foam Nozzle to use

Foam Nozzle Chart

Suttner ST-75 Brass Foam Head 4,000 PSI with #7.5 Air Injector Nozzle and 1/4" F Inlet. The ST-75 produces thick foam for an easy and safe application and to save on chemical usage by reducing splash and drift of chemicals

Features
• By means of the foam head ST-75 different foam applications are possible as the air injector nozzle is easily exchangeable and adaptable
• The flat spray nozzle can be infinitely adapted from the vertical position to the horizontal one
• The maximum flow is dependent on the chosen nozzle size
• By means of the integrated air injector in the foam head the air is sucked in on the face side
• Independent of the length of the lance a constant foam quality is guaranteed
• The spraying result is especially even as a high quality foam nozzle insert is used

ST-75 with ST-160 Chemical Injector on YouTube

Specifications
• Air Injector Nozzle Size: 7.5
• Max Pressure: 4,000 PSI
• Flow Rate: 1 - 6 GPM
• Max Temp: 212° F.
• Inlet: 1/4" Female
• Note: Suttner ST-160, ST-160M or St-164 Chemical or Foam injector required and is not included
• Weight: 0.31 lb

Please use Nozzle Chart to determine proper Spray Nozzle Size

Nozzle Chart

Use Spray Nozzle Size and Foam Nozzle Chart to determine correct Foam Nozzle to use

Foam Nozzle Chart

Suttner ST-75 Brass Foam Head 4,000 PSI with #8.0 Air Injector Nozzle and 1/4" F Inlet. The ST-75 produces thick foam for an easy and safe application and to save on chemical usage by reducing splash and drift of chemicals

Features
• By means of the foam head ST-75 different foam applications are possible as the air injector nozzle is easily exchangeable and adaptable
• The flat spray nozzle can be infinitely adapted from the vertical position to the horizontal one
• The maximum flow is dependent on the chosen nozzle size
• By means of the integrated air injector in the foam head the air is sucked in on the face side
• Independent of the length of the lance a constant foam quality is guaranteed
• The spraying result is especially even as a high quality foam nozzle insert is used

ST-75 with ST-160 Chemical Injector on YouTube

Specifications
• Air Injector Nozzle Size: 8.0
• Max Pressure: 4,000 PSI
• Flow Rate: 1 - 6 GPM
• Max Temp: 212° F.
• Inlet: 1/4" Female
• Note: Suttner ST-160, ST-160M or St-164 Chemical or Foam injector required and is not included
• Weight: 0.31 lb

Please use Nozzle Chart to determine proper Spray Nozzle Size

Nozzle Chart

Use Spray Nozzle Size and Foam Nozzle Chart to determine correct Foam Nozzle to use

Foam Nozzle Chart

Suttner ST-75.2 Long Range Foam Nozzle 5,000 PSI with #13.0 Air Injector Nozzle and 1/4" FPT Inlet. The ST-75 Long Rang foam nozzle throw foam up to 40 feet

Features
• By means of the foam head ST-75 different foam applications are possible as the air injector nozzle is easily exchangeable and adaptable
• The maximum flow is dependent on the chosen nozzle size
• 1/4” Stainless steel inlet

Specifications
• Air Injector Nozzle Size: 13.0
• Max Pressure: 5,000 PSI
• Flow Rate: up to 12 GPM
• Inlet: 1/4" FPT
• Note: Suttner ST-160, ST-160M or St-164 Chemical or Foam injector required and is not included
• Weight: 0.75 lb

Please use Nozzle Chart to determine proper Spray Nozzle Size

Nozzle Chart

Use Spray Nozzle Size and Foam Nozzle Chart to determine correct Foam Nozzle to use

Foam Nozzle Chart

Suttner ST-75.2 Long Range Foam Nozzle 5,000 PSI with #15 Air Injector Nozzle and 1/4" FPT Inlet. The ST-75 Long Rang foam nozzle throw foam up to 40 feet

Features
• By means of the foam head ST-75.2 different foam applications are possible as the air injector nozzle is easily exchangeable and adaptable
• The maximum flow is dependent on the chosen nozzle size
• 1/4” Stainless steel inlet

ST-75 Long Range Foamer with ST-160 Chemical Injector on YouTube

Specifications
• Air Injector Nozzle Size: 15
• Max Pressure: 5,000 PSI
• Flow Rate: up to 7 GPM
• Inlet: 1/4" FPT
• Note: Suttner ST-160, ST-160M or St-164 Chemical or Foam injector required and is not included
• Weight: 0.75 lb

Please use Nozzle Chart to determine proper Spray Nozzle Size

Nozzle Chart

Use Spray Nozzle Size and Foam Nozzle Chart to determine correct Foam Nozzle to use

Foam Nozzle Chart

Suttner ST-75.2 Long Range Foam Nozzle 5,000 PSI with #15.0 Air Injector Nozzle and 1/4" FPT Inlet. The ST-75 Long Rang foam nozzle throw foam up to 40 feet

Features
• By means of the foam head ST-75 different foam applications are possible as the air injector nozzle is easily exchangeable and adaptable
• The maximum flow is dependent on the chosen nozzle size
• 1/4” Stainless steel inlet

Specifications
• Air Injector Nozzle Size: 15.0
• Max Pressure: 5,000 PSI
• Flow Rate: up to 12 GPM
• Inlet: 1/4" FPT
• Note: Suttner ST-160, ST-160M or St-164 Chemical or Foam injector required and is not included
• Weight: 0.75 lb

Please use Nozzle Chart to determine proper Spray Nozzle Size

Nozzle Chart

Use Spray Nozzle Size and Foam Nozzle Chart to determine correct Foam Nozzle to use

Foam Nozzle Chart

Suttner ST-75.2 Long Range Foam Nozzle 5,000 PSI with #20.0 Air Injector Nozzle and 1/4" FPT Inlet. The ST-75.2 Long Rang foam nozzle throw foam up to 40 feet

Features
• By means of the foam head ST-75 different foam applications are possible as the air injector nozzle is easily exchangeable and adaptable
• The maximum flow is dependent on the chosen nozzle size
• 1/4” Stainless steel inlet

Specifications
• Air Injector Nozzle Size: 20.0
• Max Pressure: 5,000 PSI
• Flow Rate: up to 12 GPM
• Inlet: 1/4" FPT
• Note: Suttner ST-160, ST-160M or St-164 Chemical or Foam injector required and is not included
• Weight: 0.75 lb

Please use Nozzle Chart to determine proper Spray Nozzle Size

Nozzle Chart

Use Spray Nozzle Size and Foam Nozzle Chart to determine correct Foam Nozzle to use

Foam Nozzle Chart

Suttner ST-75.2 Long Range Foam Nozzle 5,000 PSI with #6.5 Air Injector Nozzle and 1/4" FPT Inlet. The ST-75 Long Rang foam nozzle throw foam up to 40 feet

Features
• By means of the foam head ST-75.2 different foam applications are possible as the air injector nozzle is easily exchangeable and adaptable
• The maximum flow is dependent on the chosen nozzle size
• 1/4” Stainless steel inlet

ST-75 Long Range Foamer with ST-160 Chemical Injector on YouTube

Specifications
• Air Injector Nozzle Size: 6.5
• Max Pressure: 5,000 PSI
• Flow Rate: up to 7 GPM
• Inlet: 1/4" FPT
• Note: Suttner ST-160, ST-160M or St-164 Chemical or Foam injector required and is not included
• Weight: 0.75 lb

Please use Nozzle Chart to determine proper Spray Nozzle Size

Nozzle Chart

Use Spray Nozzle Size and Foam Nozzle Chart to determine correct Foam Nozzle to use

Foam Nozzle Chart

Suttner ST-75.2 Long Range Foam Nozzle 5,000 PSI with #7.5 Air Injector Nozzle and 1/4" FPT Inlet. The ST-75 Long Rang foam nozzle throw foam up to 40 feet

Features
• By means of the foam head ST-75 different foam applications are possible as the air injector nozzle is easily exchangeable and adaptable
• The maximum flow is dependent on the chosen nozzle size
• 1/4” Stainless steel inlet

Specifications
• Air Injector Nozzle Size: 7.5
• Max Pressure: 5,000 PSI
• Flow Rate: up to 7 GPM
• Inlet: 1/4" FPT
• Note: Suttner ST-160, ST-160M or St-164 Chemical or Foam injector required and is not included
• Weight: 0.75 lb

Please use Nozzle Chart to determine proper Spray Nozzle Size

Nozzle Chart

Use Spray Nozzle Size and Foam Nozzle Chart to determine correct Foam Nozzle to use

Foam Nozzle Chart

Suttner ST-75S Stainless Steel Food Grade Head 4,000 PSI with #10.0 Air Injector Nozzle and 1/4" F Inlet. The ST-75 produces thick foam for an easy and safe application and to save on chemical usage by reducing splash and drift of chemicals

Features
• By means of the foam head ST-75S different foam applications are possible as the air injector nozzle is easily exchangeable and adaptable
• The flat spray nozzle can be infinitely adapted from the vertical position to the horizontal one
• The maximum flow is dependent on the chosen nozzle size
• By means of the integrated air injector in the foam head the air is sucked in on the face side
• Independent of the length of the lance a constant foam quality is guaranteed
• The spraying result is especially even as a high quality foam nozzle insert is used
• With stainless steel "wool" like foam pad
• Food grade

ST-75S Foam Nozzle on YouTube

ST-75 with ST-160 Chemical Injector on YouTube

Specifications
• Air Injector Nozzle Size: 10.0
• Max Pressure: 4,000 PSI
• Flow Rate: 1 - 6 GPM
• Max Temp: 212° F.
• Inlet: 1/4" Female
• Note: Suttner ST-160, ST-160M or St-164 Chemical or Foam injector required and is not included
• Weight: 0.31 lb

Please use Nozzle Chart to determine proper Spray Nozzle Size

Nozzle Chart

Use Spray Nozzle Size and Foam Nozzle Chart to determine correct Foam Nozzle to use

Foam Nozzle Chart

Suttner ST-75S Stainless Steel Food Grade Head 4,000 PSI with #13.0 Air Injector Nozzle and 1/4" F Inlet. The ST-75 produces thick foam for an easy and safe application and to save on chemical usage by reducing splash and drift of chemicals

Features
• By means of the foam head ST-75S different foam applications are possible as the air injector nozzle is easily exchangeable and adaptable
• The flat spray nozzle can be infinitely adapted from the vertical position to the horizontal one
• The maximum flow is dependent on the chosen nozzle size
• By means of the integrated air injector in the foam head the air is sucked in on the face side
• Independent of the length of the lance a constant foam quality is guaranteed
• The spraying result is especially even as a high quality foam nozzle insert is used
• With stainless steel "wool" like foam pad
• Food grade

ST-75S Foam Nozzle on YouTube

ST-75 with ST-160 Chemical Injector on YouTube

Specifications
• Air Injector Nozzle Size: 13.0
• Max Pressure: 4,000 PSI
• Flow Rate: 1 - 6 GPM
• Max Temp: 212° F.
• Inlet: 1/4" Female
• Note: Suttner ST-160, ST-160M or St-164 Chemical or Foam injector required and is not included
• Weight: 0.31 lb

Please use Nozzle Chart to determine proper Spray Nozzle Size

Nozzle Chart

Use Spray Nozzle Size and Foam Nozzle Chart to determine correct Foam Nozzle to use

Foam Nozzle Chart

Suttner ST-75S Stainless Steel Food Grade Head 4,000 PSI with #15.0 Air Injector Nozzle and 1/4" F Inlet. The ST-75 produces thick foam for an easy and safe application and to save on chemical usage by reducing splash and drift of chemicals

Features
• By means of the foam head ST-75S different foam applications are possible as the air injector nozzle is easily exchangeable and adaptable
• The flat spray nozzle can be infinitely adapted from the vertical position to the horizontal one
• The maximum flow is dependent on the chosen nozzle size
• By means of the integrated air injector in the foam head the air is sucked in on the face side
• Independent of the length of the lance a constant foam quality is guaranteed
• The spraying result is especially even as a high quality foam nozzle insert is used
• With stainless steel "wool" like foam pad
• Food grade

ST-75S Foam Nozzle on YouTube

ST-75 with ST-160 Chemical Injector on YouTube

Specifications
• Air Injector Nozzle Size: 15.0
• Max Pressure: 4,000 PSI
• Flow Rate: 1 - 6 GPM
• Max Temp: 212° F.
• Inlet: 1/4" Female
• Note: Suttner ST-160, ST-160M or St-164 Chemical or Foam injector required and is not included
• Weight: 0.31 lb

Please use Nozzle Chart to determine proper Spray Nozzle Size

Nozzle Chart

Use Spray Nozzle Size and Foam Nozzle Chart to determine correct Foam Nozzle to use

Foam Nozzle Chart

Suttner ST-75S Stainless Steel Food Grade Head 4,000 PSI with #5.0 Air Injector Nozzle and 1/4" F Inlet. The ST-75 produces thick foam for an easy and safe application and to save on chemical usage by reducing splash and drift of chemicals

Features
• By means of the foam head ST-75S different foam applications are possible as the air injector nozzle is easily exchangeable and adaptable
• The flat spray nozzle can be infinitely adapted from the vertical position to the horizontal one
• The maximum flow is dependent on the chosen nozzle size
• By means of the integrated air injector in the foam head the air is sucked in on the face side
• Independent of the length of the lance a constant foam quality is guaranteed
• The spraying result is especially even as a high quality foam nozzle insert is used
• With stainless steel "wool" like foam pad
• Food grade

ST-75S Foam Nozzle on YouTube

ST-75 with ST-160 Chemical Injector on YouTube

Specifications
• Air Injector Nozzle Size: 5.0
• Max Pressure: 4,000 PSI
• Flow Rate: 1 - 6 GPM
• Max Temp: 212° F.
• Inlet: 1/4" Female
• Note: Suttner ST-160, ST-160M or St-164 Chemical or Foam injector required and is not included
• Weight: 0.31 lb

Please use Nozzle Chart to determine proper Spray Nozzle Size

Nozzle Chart

Use Spray Nozzle Size and Foam Nozzle Chart to determine correct Foam Nozzle to use

Foam Nozzle Chart

Suttner ST-75S Stainless Steel Food Grade Head 4,000 PSI with #8.0 Air Injector Nozzle and 1/4" F Inlet. The ST-75 produces thick foam for an easy and safe application and to save on chemical usage by reducing splash and drift of chemicals

Features
• By means of the foam head ST-75S different foam applications are possible as the air injector nozzle is easily exchangeable and adaptable
• The flat spray nozzle can be infinitely adapted from the vertical position to the horizontal one
• The maximum flow is dependent on the chosen nozzle size
• By means of the integrated air injector in the foam head the air is sucked in on the face side
• Independent of the length of the lance a constant foam quality is guaranteed
• The spraying result is especially even as a high quality foam nozzle insert is used
• With stainless steel "wool" like foam pad
• Food grade

ST-75S Foam Nozzle on YouTube

ST-75 with ST-160 Chemical Injector on YouTube

Specifications
• Air Injector Nozzle Size: 8.0
• Max Pressure: 4,000 PSI
• Flow Rate: 1 - 6 GPM
• Max Temp: 212° F.
• Inlet: 1/4" Female
• Note: Suttner ST-160, ST-160M or St-164 Chemical or Foam injector required and is not included
• Weight: 0.31 lb

Please use Nozzle Chart to determine proper Spray Nozzle Size

Nozzle Chart

Use Spray Nozzle Size and Foam Nozzle Chart to determine correct Foam Nozzle to use

Foam Nozzle Chart

Suttner ST-76 Foam Blaster Head 3,625 PSI with #10.0 x 3 Air Injector Nozzles and 1/2" F Inlet. The foamblaster ST-76 is designed for applications in agriculture, industry, municipal cleaning and fire fighting technology. Designed for high volume applications

Features
• The foam blaster ST-76 is made out of a premium combination of stainless steel and plastic
• Starting with an inlet pressure of only 435 PSI the foam blaster ST-76 is able to foam mixtures of water and foam agents with a flow of 5.3 - 15.8 GPM and without the addition of compressed air
• By means of exchangeable air injector nozzles it is possible to adapt the foam blaster ST-76 to the requirements such as water quantity and inlet pressure in an optimal way
• Stainless steel injector nozzle
• Wider spray angle
• For applications 6 GPM or higher
• Throws foam 40 feet
• Cover large areas

ST-76 with ST-160 Chemical Injector on YouTube

Specifications
• Air Injector Nozzles (3) Size: 10.0
• Max Pressure: 3,625 PSI
• Flow Rate: 5.3 – 15.8 GPM
• Max Temp: 212° F.
• Inlet: 1/2" Female
• Note: Suttner ST-160, ST-160M or St-164 Chemical or Foam injector required and is not included
• Weight: 1.15 lb

Please use Nozzle Chart to determine proper Spray Nozzle Size

Nozzle Chart

Use Spray Nozzle Size and Foam Nozzle Chart to determine correct Foam Nozzle to use

Foam Nozzle Chart

Suttner ST-76 Foam Blaster Head 3,625 PSI with #15.0 x 3 Air Injector Nozzles and 1/2" F Inlet. The foamblaster ST-76 is designed for applications in agriculture, industry, municipal cleaning and fire fighting technology. Designed for high volume applications

Features
• The foam blaster ST-76 is made out of a premium combination of stainless steel and plastic
• Starting with an inlet pressure of only 435 PSI the foam blaster ST-76 is able to foam mixtures of water and foam agents with a flow of 5.3 - 15.8 GPM and without the addition of compressed air
• By means of exchangeable air injector nozzles it is possible to adapt the foam blaster ST-76 to the requirements such as water quantity and inlet pressure in an optimal way
• Stainless steel injector nozzle
• Wider spray angle
• For applications 6 GPM or higher
• Throws foam 40 feet
• Cover large areas

ST-76 with ST-160 Chemical Injector on YouTube

Specifications
• Air Injector Nozzles (3) Size: 15.0
• Max Pressure: 3,625 PSI
• Flow Rate: 5.3 – 15.8 GPM
• Max Temp: 212° F.
• Inlet: 1/2" Female
• Note: Suttner ST-160, ST-160M or St-164 Chemical or Foam injector required and is not included
• Weight: 1.15 lb

Please use Nozzle Chart to determine proper Spray Nozzle Size

Nozzle Chart

Use Spray Nozzle Size and Foam Nozzle Chart to determine correct Foam Nozzle to use

Foam Nozzle Chart

Suttner ST-76 Foam Blaster Head 3,625 PSI with #5.0 x 3 Air Injector Nozzles and 1/2" F Inlet. The foamblaster ST-76 is designed for applications in agriculture, industry, municipal cleaning and fire fighting technology. Designed for high volume applications

Features
• The foam blaster ST-76 is made out of a premium combination of stainless steel and plastic
• Starting with an inlet pressure of only 435 PSI the foam blaster ST-76 is able to foam mixtures of water and foam agents with a flow of 5.3 - 15.8 GPM and without the addition of compressed air
• By means of exchangeable air injector nozzles it is possible to adapt the foam blaster ST-76 to the requirements such as water quantity and inlet pressure in an optimal way
• Stainless steel injector nozzle
• Wider spray angle
• For applications 6 GPM or higher
• Throws foam 40 feet
• Cover large areas

ST-76 with ST-160 Chemical Injector on YouTube

Specifications
• Air Injector Nozzles (3) Size: 5.0
• Max Pressure: 3,625 PSI
• Flow Rate: 5.3 – 15.8 GPM
• Max Temp: 212° F.
• Inlet: 1/2" Female
• Note: Suttner ST-160, ST-160M or St-164 Chemical or Foam injector required and is not included
• Weight: 1.15 lb

Please use Nozzle Chart to determine proper Spray Nozzle Size

Nozzle Chart

Use Spray Nozzle Size and Foam Nozzle Chart to determine correct Foam Nozzle to use

Foam Nozzle Chart

Suttner ST-76 Foam Blaster Head 3,625 PSI with #7.0 x 3 Air Injector Nozzles and 1/2" F Inlet. The foamblaster ST-76 is designed for applications in agriculture, industry, municipal cleaning and fire fighting technology. Designed for high volume applications

Features
• The foam blaster ST-76 is made out of a premium combination of stainless steel and plastic
• Starting with an inlet pressure of only 435 PSI the foam blaster ST-76 is able to foam mixtures of water and foam agents with a flow of 5.3 - 15.8 GPM and without the addition of compressed air
• By means of exchangeable air injector nozzles it is possible to adapt the foam blaster ST-76 to the requirements such as water quantity and inlet pressure in an optimal way
• Stainless steel injector nozzle
• Wider spray angle
• For applications 6 GPM or higher
• Throws foam 40 feet
• Cover large areas

ST-76 with ST-160 Chemical Injector on YouTube

Specifications
• Air Injector Nozzles (3) Size: 7.0
• Max Pressure: 3,625 PSI
• Flow Rate: 5.3 – 15.8 GPM
• Max Temp: 212° F.
• Inlet: 1/2" Female
• Note: Suttner ST-160, ST-160M or St-164 Chemical or Foam injector required and is not included
• Weight: 1.15 lb

Please use Nozzle Chart to determine proper Spray Nozzle Size

Nozzle Chart

Use Spray Nozzle Size and Foam Nozzle Chart to determine correct Foam Nozzle to use

Foam Nozzle Chart

Suttner ST-76 Foam Blaster Head 3,625 PSI with #7.5 x 3 Air Injector Nozzles and 1/2" F Inlet. The foamblaster ST-76 is designed for applications in agriculture, industry, municipal cleaning and fire fighting technology. Designed for high volume applications

Features
• The foam blaster ST-76 is made out of a premium combination of stainless steel and plastic
• Starting with an inlet pressure of only 435 PSI the foam blaster ST-76 is able to foam mixtures of water and foam agents with a flow of 5.3 - 15.8 GPM and without the addition of compressed air
• By means of exchangeable air injector nozzles it is possible to adapt the foam blaster ST-76 to the requirements such as water quantity and inlet pressure in an optimal way
• Stainless steel injector nozzle
• Wider spray angle
• For applications 6 GPM or higher
• Throws foam 40 feet
• Cover large areas

ST-76 with ST-160 Chemical Injector on YouTube

Specifications
• Air Injector Nozzles (3) Size: 7.5
• Max Pressure: 3,625 PSI
• Flow Rate: 5.3 – 15.8 GPM
• Max Temp: 212° F.
• Inlet: 1/2" Female
• Note: Suttner ST-160, ST-160M or St-164 Chemical or Foam injector required and is not included
• Weight: 1.15 lb

Please use Nozzle Chart to determine proper Spray Nozzle Size

Nozzle Chart

Use Spray Nozzle Size and Foam Nozzle Chart to determine correct Foam Nozzle to use

Foam Nozzle Chart

Suttner ST-76 Foam Blaster Head 3,625 PSI with #8.0 x 3 Air Injector Nozzles and 1/2" F Inlet. The foamblaster ST-76 is designed for applications in agriculture, industry, municipal cleaning and fire fighting technology. Designed for high volume applications

Features
• The foam blaster ST-76 is made out of a premium combination of stainless steel and plastic
• Starting with an inlet pressure of only 435 PSI the foam blaster ST-76 is able to foam mixtures of water and foam agents with a flow of 5.3 - 15.8 GPM and without the addition of compressed air
• By means of exchangeable air injector nozzles it is possible to adapt the foam blaster ST-76 to the requirements such as water quantity and inlet pressure in an optimal way
• Stainless steel injector nozzle
• Wider spray angle
• For applications 6 GPM or higher
• Throws foam 40 feet
• Cover large areas

ST-76 with ST-160 Chemical Injector on YouTube

Specifications
• Air Injector Nozzles (3) Size: 8.0
• Max Pressure: 3,625 PSI
• Flow Rate: 5.3 – 15.8 GPM
• Max Temp: 212° F.
• Inlet: 1/2" Female
• Note: Suttner ST-160, ST-160M or St-164 Chemical or Foam injector required and is not included
• Weight: 1.15 lb

Please use Nozzle Chart to determine proper Spray Nozzle Size

Nozzle Chart

Use Spray Nozzle Size and Foam Nozzle Chart to determine correct Foam Nozzle to use

Foam Nozzle Chart

Suttner ST-8 Adjustable Float Valve Assembly with 1/2'' FNPT Inlet. Used to regulate the maximum water level in a float tank. When the maximum water level drops the float valve opens

Features:
• Valve housing and connection are corrosion resistant material, brass and plastics
• Adjustable float

Specifications:
• Inlet: 1/2" FNPT
• Max Pressure: 140 PSI
• Max. Temperature: 178° F.
• Flow Rate: 5 GPM
• Weight 0.44 lbs

Features
• High Quality, German engineered components
• Front inlet design keeps dirty hose just far enough away, keeping the operator clean
• Most economical light to medium duty spray gun ever
• Forged brass housing for maximum strength

Specifications
• Max Pressure: 3,050 PSI
• Max Flow: 8.0 GPM
• Max Temp: 320° F.
• Inlet: 3/8" Female NPT
• Outlet: 1/4" Female NPT
• Weight: 0.82 lb

Features
• High Quality, German engineered components
• Front inlet design keeps dirty hose just far enough away, keeping the operator clean
• Stainless steel spring, needle, ball and a poly seat for the best chemical resistance
• Forged brass housing for maximum strength

Specifications
• Max Pressure: 2,000 PSI
• Max Flow: 8.0 GPM
• Max Temp: 320° F.
• Inlet: 1/4" Female NPT
• Outlet: 1/4" Female NPT
• Weight: 0.82 lb

Features
• High Quality, German engineered components
• Front inlet design keeps dirty hose just far enough away, keeping the operator clean
• Stainless steel spring, needle, ball and a poly seat for the best chemical resistance
• Forged brass housing for maximum strength

Specifications
• Max Pressure: 2,000 PSI
• Max Flow: 8.0 GPM
• Max Temp: 320° F.
• Inlet: 3/8" Female NPT
• Outlet: 1/4" Female NPT
• Weight: 0.82 lb