New products

Suttner ST-7.1 Pressure Switch, 580 Switching Point (Black), 1/4" M 4,350 PSI

Features:
• IP 65 protection class
• Simultaneous N/O and N/C connection is possible
• The design of the micro switch allows comparably high inrush current (20 Amps N/C, 15 Amps N/O)
• The electrical capacity of the switch is 10.1 Amps (resistive load)
• No ingress of towing water into the environment of the microswitch possible

Suttner ST-7.1 Data Sheet

Specifications:
• Switch Point: 580 PSI (Black)
• Max. Pressure: 4,350 PS
• Voltage: 10.1 A - 250 VAC
• Max: Fluid Temperature: 194° F
• Cable Length: 37.4”
• Thread: 1/4” Male
• Material: Brass / plastic
• Protection Class” IP 65
• Weight: lbs

Suttner ST-7.1 Pressure Switch, 360 Switching Point (Red), 1/4" M 4,350 PSI

Features:
• IP 65 protection class
• Simultaneous N/O and N/C connection is possible
• The design of the micro switch allows comparably high inrush current (20 Amps N/C, 15 Amps N/O)
• The electrical capacity of the switch is 10.1 Amps (resistive load)
• No ingress of towing water into the environment of the microswitch possible

Suttner ST-7.1 Data Sheet

Specifications:
• Switch Point: 360 PSI (Red)
• Max. Pressure: 4,350 PS
• Voltage: 10.1 A - 250 VAC
• Max: Fluid Temperature: 194° F
• Cable Length: 37.4”
• Thread: 1/4” Male
• Material: Brass / plastic
• Protection Class” IP 65
• Weight: lbs

Suttner ST-601C Inline Chemical Resistant Spray Gun 4,000 PSI with Ceramic Ball. Ideal for cleaning vertical and overhead surfaces. Perfect for washing tractors, trailers, siding, windows, eaves, etc.

Features
• High Quality, German engineered components
• Superior Chemical Resistant
• Horizontal flow-through design
• Heavy duty, impact-resistant trigger guard
• Forged brass housing for maximum strength
• Unitized valve allows for higher temps and longer life
• Ceramic ball in valve is highly resistant against nearly all soaps and acids

Specifications
• Max Pressure: 4,000 PSI
• Max Flow: 12.0 GPM
• Max Temp: 300° F.
• Inlet: 3/8" Female NPT
• Outlet: 1/4" Female NPT
• Weight: 1.16 lb

Comet DWD-K 2530 G 3,000 PSI 2.3 GPM Commercial Duty Triplex Plunger Pump Fully Plumbed with Adjustable Unloader and Chemical Injector

Features:
• Direct Drive with Gas Flange 4-7 HP SAE (2-9/16 center to center)
• Forged brass manifold and ceramic plungers to prevent pitting and wear
• Built-in unloader and chemical injector for quick plug and play on systems
• Lubricated double seal packings to increase pump longevity (high & low)
• Anodized crankcase to protect from the harshest elements
• Ceramic Plungers
• Stainless steel check valves to keep pump at optimal performance.
• Featuring a 3/4” hollow shaft with flange for coupling to gas engines.

ADDITIONAL FEATURES OF PLUMBED MADE READY PUMP:
• 3 Foot soap hose with filter
• 3/8” QC plug
• Thermal relief valve
• Garden hose adapter with spring

Comet DWD G-K Data Sheet

Specifications:
• Max. Volume: 2.3 GPM
• Max. Discharge Pressure: 3,000 PSI
• Max. Pump Speed: 3,400 RPM
• Shaft Diameter: 3/4” Hollow
• Maximum Horsepower Requirements: 6.3 GHP
• Inlet Port: 3/4" GH (garden hose)
• Outlet Port: 22M-14 Male Twist Connect with 3/8" QC Plug
• Note: Optional D10088 3/8" QD Coupler shown below
• Weight: 11.55 lb.

Delavan SmartFLO™ Series 3120-423F-SB 2.0 GPM 85-100 PSI Diaphragm Demand-Bypass Pump with On/Off Switch, 3/8” Female Threaded Ports. SmartFLO™ technology automatically adapts flow rates to provide optimal performance in any application. Harmful rapid switch cycling is completely eliminated to extend pump life with no additional setup required

SmartFLO™:
• Combines the advantages of both Bypass and Demand Controls
• Utilizes Pressure Sensing Demand Switch AND Internal Bypass Valve
• Automatically adapts to changing system demands
• Constant and instant flow eliminates pump cycling
• Will turn off when not in use and outlets are closed
• Low chance of overheating when run for long periods

Fits All Applications:
• RV and Marine systems
• Small to medium size sprayers
• Multi-outlet systems

Features:
• 100% Factory tested
• Self-Priming
• Can be run dry
• High Torque Motor for superior flow at pressure
• On/Off switch at base of pump
• 2 Year warranty from date of purchase

SmartFLO Pump Model 3222-421F-SB Video

Specifications:
• Pump Type: Bypass - Demand, 3-chamber positive displacement
• Flow: Up to 2.0 GPM
• Valves: Viton
• Diaphragm: Santoprene
• Power: 12VDC
• Leads: 12 AWG, 6” long with 2-pin molded connector
• Amps: 8.5 Max
• Pressure Settings: 85-100 PSI
• Inlet/Outlet Ports: 3/8” FPT
• Packaging: Small box
• Weight: 5.6 lbs

Delavan SmartFLO™ Series 3120-421F-SB 2.0 GPM 85-100 PSI Diaphragm Demand-Bypass Pump with 3/8” Female Threaded Ports. SmartFLO™ technology automatically adapts flow rates to provide optimal performance in any application. Harmful rapid switch cycling is completely eliminated to extend pump life with no additional setup required

SmartFLO™:
• Combines the advantages of both Bypass and Demand Controls
• Utilizes Pressure Sensing Demand Switch AND Internal Bypass Valve
• Automatically adapts to changing system demands
• Constant and instant flow eliminates pump cycling
• Will turn off when not in use and outlets are closed
• Low chance of overheating when run for long periods

Fits All Applications:
• RV and Marine systems
• Small to medium size sprayers
• Multi-outlet systems

Features:
• 100% Factory tested
• Self-Priming
• Can be run dry
• High Torque Motor for superior flow at pressure
• 2 Year warranty from date of purchase

SmartFLO Pump Model 3222-421F-SB Video

Specifications:
• Pump Type: Bypass - Demand, 3-chamber positive displacement
• Flow: Up to 2.0 GPM
• Valves: Viton
• Diaphragm: Santoprene
• Power: 12VDC
• Leads: 12 AWG, 6” long with 2-pin molded connector
• Amps: 8.5 Max
• Pressure Settings: 85-100 PSI
• Inlet/Outlet Ports: 3/8” FNPT
• Packaging: Small box
• Weight: 5.6 lbs

Delavan SmartFLO™ Series 3222-421F-SB 2.2 GPM 85-100 PSI Diaphragm Demand-Bypass Pump with 3/4” Quick Attach Ports. SmartFLO™ technology automatically adapts flow rates to provide optimal performance in any application. Harmful rapid switch cycling is completely eliminated to extend pump life with no additional setup required

SmartFLO™:
• Combines the advantages of both Bypass and Demand Controls
• Utilizes Pressure Sensing Demand Switch AND Internal Bypass Valve
• Automatically adapts to changing system demands
• Constant and instant flow eliminates pump cycling
• Will turn off when not in use and outlets are closed
• Low chance of overheating when run for long periods

Fits All Applications:
• RV and Marine systems
• Small to medium size sprayers
• Multi-outlet systems

Features:
• 100% Factory tested
• Self-Priming
• Can be run dry
• High Torque Motor for superior flow at pressure
• 2 Year warranty from date of purchase

SmartFLO Pump Model 3222-421F-SB Video

Specifications:
• Pump Type: Bypass - Demand, 3-chamber positive displacement
• Flow: Up to 2.2 GPM
• Valves: Viton
• Diaphragm: Santoprene
• Power: 12VDC
• Leads: 12 AWG, 6” long with 2-pin molded connector
• Amps: 8.5 Max
• Pressure Settings: 85-100 PSI
• Inlet/Outlet Ports: 3/4” Quick Attach Ports
• Packaging: Small box
• Weight: 5.6 lbs

Suttner ST-458 # 12.0 Hydro Ex Turbo Nozzle with Red Extended Poly Cover. This 1/2” Inlet hydro excavation nozzle is rated up to 6,000 PSI.

Features
• The outlet cover extension greatly decreases the chance of dirt and debris getting to the nozzle tip and seat area
• Significant Increase in lifetime of nozzle
• Molded and wear resistant poly cover

Hydro Ex Nozzle Flyer

Specifications
• Nozzle Size # 12.0
• Max PSI: 6,000
• Max Temp.: 190° F
• Inlet: 1/2" Female NPT
• NOTE: All rotating nozzles should be started pointing downward
• Weight: 1.60 lbs

Please use Nozzle Chart to determine proper nozzle size

Nozzle Chart

Suttner 240º F Temperature Gauge, Mounts to 1/4" Spray Lances

Specifications:
• Mounts easily to 1/4” spray lances
• Simple way to monitor water temperature
• Great tool for your service technician
• Note: Lance not included
• Weight: 0.37 lbs.

Suttner 240º F Temperature Gauge, Mounts to 1/2" Hydro Ex Lances

Specifications:
• Mounts easily to 1/2” hydro excavation spray lances
• Simple way to monitor water temperature
• Great tool for your service technician
• Note: Lance not included
• Weight: 0.37 lbs.

General Pump DCG5010SO Compensating Low Fatigue Rear Inlet Trigger Gun (Safety Orange) 5,000 PSI 10.5 GPM

Features:
• Exclusive patent-pending GP design
• Unique design compensates for changes in pressure
• Trigger designed for low fatigue
• Allows for continued use without tiring hand
• All flow passages designed for minimum pressure drop - maximum flow
• Fluorocarbon seals for maximum high temperature performance
• Large comfortable hand grip to accommodate work gloves
• Additional venting for excellent high temperature performance
• Durable glass-filled housing and ABS trigger
• High visibility safety orange

Specifications:
• Max Volume: 10.5 GPM
• Max Pressure: 5,000 PSI
• Max Temp: 320° F.
• Inlet: 3/8" NPT-F
• Outlet: 1/4" NPT-F
• Materials: Brass, Stainless Steel, Plastic, Viton
• Weight: 1.5 lbs

3,045 PSI 3.4 GPM General EP1508G8 Direct Drive Pump Made Ready W/ PULSAR4KHPEZ EZ Start Unloader. Pump is ready to use right out of the box

PUMP:
• General EP1508G8 Pump with SAE J609 Gas Flange
• Direct Drive with Gas Flange 9.0-13.0 HP SAE
• Max. Volume: 3.4 GPM
• Max. Discharge Pressure: 3,045 PSI
• Max. Pump Speed: 3,400 RPM
• Shaft Diameter: 1” Hollow
• Max. Horsepower Requirements: 10.6 GHP
• Max. Fluid Temp.: 165º F
• New Forged brass manifold , increases working pressure to 4,000 PSI
• Solid ceramic plungers with dual guide system

COMPONENTS:
• General EP1508G8 Triplex Plunger Pump
• PULSAR4KHPEZ EZ Start Unloader 4,050 PSI, 10 GPM
• Thermal relief valve
• 3/8” Hose Barb and Clamp Keeps Hose Secure and Sealed
• 3/4” Garden Hose Inlet Fitting with 1/4” Side Port
• 3/8” QC brass socket Installed and 3/8” QC Plug Included
• Mounting bolts
• Note: Pumps are not tested prior to shipping and unloader will need to be adjusted
• Weight: 19.90 lb

General Pump 2560001 Multi-Nozzle Holder (Accepts 1/4" MPT Nozzles)

Features
• This handy tool allows you to very quickly switch between four different nozzles on one spray gun wand.
• It accepts any 1/4" NPT-M thread spray nozzles and turns each one into a quick-connect tip.
• Works great for changing between foam and water, reaching multiple height levels, or altering the intensity of the spray without having to carry around several individual nozzles!
• Note: Nozzles not included.

Specifications

Specifications
• Dimensions: 0.70” H x 3.30” L
• Replaces JROD #6540
• Weight: 0.25 lb

Suttner ST-83 Air Powered Disinfecting Cold Fogger. The ST-83 is perfect for fogging on sanitary solutions in restaurants, hotels, hospitals, nursing homes, public transportation, taxis, rental cars, agricultural and food processing facilities. The fine spray or fog pattern that this device produces allows sanitary solutions to reach all around the items and areas being cleaned. It also provides an effective and uniform wetting of the surface

Features
• It's easy to use. Fill the bottle with your sanitizing solution, attach to an air compressor and start fogging on the sanitizing solution
• Corrosion resistant stainless steel & plastic
• Inexpensive and safe application for hygienically germ-free cleaning of interiors to remove microorganisms, viruses and bacteria
• No inhalation of the disinfectant solution as rooms do not have to be entered
• The finest nebulization of active ingredients comes into the smallest gaps and into the last corner
• A compressed air connection is required 
• Uniform spray pattern with the finest droplets under 30 μm.
• Extremely productive use: e.g. 1 liter for rooms with 60 m3, room size of approx. 25 m2
• Easy dosing of the disinfectant by ml scale, (100 ml each.)
• Accessories available: adapter for 5 - 30 liter canister, further dosing nozzles from our range

Compressor Requirments:
• Commercially available compressed air systems or compressors can be used to supply the fog device with compressed air
• The compressor should provide a flow rate of 120 - 180 L / min.
• The working pressure should be at least 3 bar.
• If not available, we recommend installing a pressure reducer (item 150008010) between the compressor outlet and the ST-83.
• With this the operating pressure - working pressure on the ST-83 can be set exactly.
• Make sure that the cross-section of the hose from the compressor to the ST-83 is correct. The longer the hose, the larger its cross section should be. 20 meters hose length ID 8 mm / 100 meters hose length ID 10 mm

See ST-83 in action on YouTube

Agriculture, breeding and food industry

Medical practices, hospitals and nursing homes

Public transport, taxis and rental cars

Hotels and restaurants

Operation manual

Specifications
• Nozzle Inserts: 2 with different spray patterns
• Material: Stainless steel & plastic
• Air Inlet: 1/4" Female NPT
• Bottle:1 Litre
• Note: Air compressor required for operation (Not Included)
• Weight: 2.35 lb

General Pump D10089 3/8” Quick Disconnect Plug x M22-14MM M Twist Plug 4,000 PSI

Features:
• Adapts from quick connect to 22mm twist connect
• Zinc plated steel

Specifications:
• 3/8" QD Plug
• Male M22, Yoke/Stem: 14MM
• Max Temp: 175°
• Max Operating Pressure: 4,000 PSI
• Weight: 0.12 lb

General Pump D10037 3/8” Quick Disconnect Plug x M22-14MM F Twist Coupler 4,000 PSI

Features:
• Adapts from quick connect to 22mm twist connect
• Brass & zinc plated steel
• EPDM O-Ring

Specifications:
• 3/8" QD Plug
• Female M22, Yoke/Stem: 14MM
• Max Temp: 175°
• Max Operating Pressure: 4,000 PSI
• Replaces 6322
• Weight: 0.24 lb

General Pump PMRPULSAR4KHPEZ- Unloader and Kit 4,050 PSI 10.5 GPM

Features
• PULSAR4KHPEZ Unloader, 4050 PSI, 10 GPM
• 3/8" Quick Coupler and 3/8" Plug Included
• 3/4" Garden Hose Inlet Fitting with 1/4" Side Port
• 3/8" Hose Barb and Clamp Keeps Hose Secure and Sealed
• Flow through design
• General Pump recommends installing a secondary relief and pressure gauge

Specifications
• Maximum Temperature: 195° F
• Max GPM: 10.5
• Maximum PSI: 4,050
• Inlet: (2) 3/8" NPT-F
• Outlet: 3/8" NPT-F
• Bypass (2) 3/8" NPT-F
• Weight: 3.15 Lbs

General Pump 100438 Capillary Style 86° - 195° Adjustable Thermostat. Probe Style Thermostat Insulated SS Capillary Copper Immersion Bulb (UL/CSA approved), 16(4)A-380V Electric Rating

Features:
• Panel mounted, dual scale knob.
• Rapid response, ± 5° F
• 60 Inch capillary tube with bulb rated to 4,000 PSI
• UL/CSA approved

Specifications:
• Temp Range: 86°- 195º F
• Max. Pressure: 4,000 PSI
• Electrical Rating AC: 120VAC-20A, 240VAC-20A, 120/240VAC-1/4HP
• Sensing Element: Copper Bulb
• UL/CSA Approved: Yes
• Weight: 0.40 Lb

General Pump 100438 Capillary Style 86° - 302° Adjustable Thermostat. Probe Style Thermostat Insulated SS Capillary Copper Immersion Bulb (UL/CSA approved), 16(4)A-380V Electric Rating

Features:
• Panel mounted, dual scale knob.
• Rapid response, ± 5° F
• 60 Inch capillary tube with bulb rated to 4,000 PSI
• UL/CSA approved

Specifications:
• Temp Range: 86°- 302º F
• Max. Pressure: 4,000 PSI
• Electrical Rating AC: 120VAC-20A, 240VAC-20A, 120/240VAC-1/4HP
• Sensing Element: Copper Bulb
• UL/CSA Approved: Yes
• Weight: 0.40 Lb

General Pump 100438 Capillary Style 86° - 250° Adjustable Thermostat. Probe Style Thermostat Insulated SS Capillary Copper Immersion Bulb (UL/CSA approved), 16(4)A-380V Electric Rating

Features:
• Panel mounted, dual scale knob.
• Rapid response, ± 5° F
• 60 Inch capillary tube with bulb rated to 4,000 PSI
• UL/CSA approved

Specifications:
• Temp Range: 86°- 250º F
• Max. Pressure: 4,000 PSI
• Electrical Rating AC: 120VAC-20A, 240VAC-20A, 120/240VAC-1/4HP
• Sensing Element: Copper Bulb
• UL/CSA Approved: Yes
• Weight: 0.40 Lb

General Pump DCG5010 Compensating Low Fatigue Rear Inlet Trigger Gun 5,000 PSI 10.5 GPM

Features:
• Exclusive patent-pending GP design
• Unique design compensates for changes in pressure
• Trigger designed for low fatigue
• Allows for continued use without tiring hand
• All flow passages designed for minimum pressure drop - maximum flow
• Fluorocarbon seals for maximum high temperature performance
• Large comfortable hand grip to accommodate work gloves
• Additional venting for excellent high temperature performance
• Durable glass-filled housing and trigger in Zytel (high tech nylon)

Specifications:
• Max Volume: 10.5 GPM
• Max Pressure: 5,000 PSI
• Max Temp: 320° F.
• Inlet: 3/8" NPT-F
• Outlet: 1/4" NPT-F
• Materials: Brass, Stainless Steel, Plastic, Viton
• Weight: 1.5 lbs

General Pump YDL41SSB / PA LD 9 41” Stainless Steel Molded Grip Dual Lance 4,050 PSI

Features:
• Double lance, with two tubes. First one for high pressure fluid and second one, deviced with handle, for low pressure detergent
• Provide a convenient method of operating a downstream chemical injection system by turning the insulated adjustment handle
• Designed for hot or cold water systems
• Made in Italy

Specifications:
• Length: 41"
• Inlet: 1/4" NPT-M
• Outlet Nozzle Fittings (2): 1/4" NPT-F
• Rated Pressure: 3,650 PSI
• Max. Pressure: 4,050 PSI
• Max. Volume: 10.5 GPM
• Max. Temp.: 320° F
• Materials: Stainless Steel, Brass, Plastic, Buna-N
• Note: Nozzles not included
• Weight: 2.25 lbs

2,610 PSI 2.9 GPM General PMRET1506G6 Direct Drive Pump Made Ready W/ PULSAR4KHPEZ EZ Start Unloader. Pump is ready to use right out of the box

PUMP:
• General ET1506G6 Pump with SAE J609A Gas Flange
• Direct Drive with Gas Flange 5.0-7.0 HP SAE
• Max. Volume: 2.9 GPM
• Max. Discharge Pressure: 2,610 PSI
• Max. Pump Speed: 3,400 RPM
• Shaft Diameter: 3/4” Hollow
• Max. Horsepower Requirements: 6.9 GHP
• Max. Fluid Temp.: 165º F
• New “HR” anti-corrosion surface treatment on manifold
• Solid ceramic plungers

COMPONENTS:
• General ET1506G6 Triplex Plunger Pump
• PULSAR4KHPEZ EZ Start Unloader 4,050 PSI, 10 GPM
• Thermal relief valve
• 3/8” Hose Barb and Clamp Keeps Hose Secure and Sealed
• 3/4” Garden Hose Inlet Fitting with 1/4” Side Port
• 3/8” QC brass socket and 3/8” QC Plug Included
• Mounting bolts
• Note: Pumps are not tested prior to shipping and unloader will need to be adjusted
• Weight: 14.90 lb

Valley Industries 0120DSB15 Series 20 Dual Scale General Service 15 PSI Bottom Mount 1-1/2" Steel Case Pressure Gauge. These gauges are designed for use with gas, oil, and water or any medium not corrosive to brass or bronze

Features:
• Dial Range (PSI): 0 – 15
• Dial Range (BAR): 0 – 1
• Casing: 1-1/2" Diameter
• Movement: Brass
• Bourdon Tube: C-Shaped in copper alloy
• Pointer: Black enameled aluminum
• Dial: White aluminum
• Window: Acrylic
• Case Material: Steel, black painted
• Bezel: Chrome plated
• Mounting: Bottom
• Connection Material: Brass
• Connection Size: 1/8" MNPT
• Accuracy: ASME/ANSI B40.1 Grade B (3-2-3%)
• Fill Material: Dry
• Wetted Parts: Copper alloy

Delavan 7971-104E-SB PowerFLO™ Advanced FB3 Series 115/120VAC 7.0 GPM 60 PSI Diaphragm Pump with 3/4” Quick Attach Ports. Demand Switch – Operates only when liquid flow is required.

Features:
• FB3 pumps are Delavan’s new advanced 115/120VAC smooth running, five chamber diaphragm pumps that features Extended Pump Life and Improved Performance
• The FB3 is the most advanced, high flow 115/120VAC pump on the market, built with quality components, such as stainless fasteners, and high torque motors standard
• The new diaphragm retaining system allows the pump to maintain its flow for longer hours of operation in demanding applications
• The FB3 pumps feature Santoprene diaphragms and valves, to handle the FB3 pumps’ higher flow rates
• The FB3 pump uses a heavy duty demand switch system that extends the life of the pump by turning it off when not in use
• Like all Delavan diaphragm pumps, this heavy duty pump can run dry and will self-prime
• Made in the USA
• 100% Factory tested
• 2 Year warranty from date of purchase

Motor:
• Type: 115/120VAC Totally enclosed, non-ventilated
• Power Cord: 6’ with plug
• Amps: 1.5 Max

Materials of Construction:
• Motor Shell: Coated Steel
• Housing: Polypropylene
• Valves: Santoprene
• Diaphragm: Santoprene/Stainless Steel
• Fasteners: Stainless Steel

Pump:
• Demand Switch – Operates only when liquid flow is required
• Type: 5-chamber positive displacement
• Capable of being run dry
• Excellent self-priming capability
• Liquid Temperature: 140° F Max.
• Priming Capabilities: 14’
• Max. Flow: 7.0 GPM
• Pressure Shut-Off: 60 PSI
• Inlet/Outlet Ports: 3/4” Quick Attach
• Packaging: Small box
• Weight: 10.15 lbs

Delavan 7971-114E-SB PowerFLO™ Advanced FB3 Series 115/120VAC 7.0 GPM 60 PSI Diaphragm Pump with 3/4” Quick Attach Ports. Bypass Design – Continuous operation.

Features:
• FB3 pumps are Delavan’s new advanced 115/120VAC smooth running, five chamber diaphragm pumps that features Extended Pump Life and Improved Performance
• The FB3 is the most advanced, high flow 115/120VAC pump on the market, built with quality components, such as stainless fasteners, and high torque motors standard
• The new diaphragm retaining system allows the pump to maintain its flow for longer hours of operation in demanding applications
• The FB3 pumps feature Santoprene diaphragms and valves, to handle the FB3 pumps’ higher flow rates
• Like all Delavan diaphragm pumps, this heavy duty pump can run dry and will self-prime
• Made in the USA
• 100% Factory tested
• 2 Year warranty from date of purchase

Motor:
• Type: 115/120VAC Totally enclosed, non-ventilated
• Power Cord: 6’ with plug
• Amps: 1.5 Max

Materials of Construction:
• Motor Shell: Coated Steel
• Housing: Polypropylene
• Valves: Santoprene
• Diaphragm: Santoprene/Stainless Steel
• Fasteners: Stainless Steel

Manufacturer Recommendation:
• If you are going to be running continuous use with any bypass model of pump, Delavan also recommends that you purchase a heat sink for the motor

Pump:
• Bypass Design – Continuous operation with internal bypass
• Type: 5-chamber positive displacement
• Capable of being run dry
• Excellent self-priming capability
• Liquid Temperature: 140° F Max.
• Priming Capabilities: 14’
• Max. Flow: 7.0 GPM
• Max Pressure: 60 PSI
• Inlet/Outlet Ports: 3/4” Quick Attach
• Packaging: Small box
• Weight: 10.15 lbs

Delavan PowerFLO™ 5850 Series 5.0 GPM 60 PSI Diaphragm Pump. Bypass Design – Continuous operation

Features:
• Certified to NSF/ANSI Standard 61 & 372
• Made in the USA
• 100% Factory tested
• 2 Year warranty from date of purchase

Motor:
• Type: 12 VDC permanent magnet, totally enclosed, non-ventilated
• Leads: 14 AWG, 12” long with Delphi Weatherproof Electrical 2 Pin Connector
• Amps: 20 Max
• Duty Cycle: See Heat Rise graph

Materials of Construction:
• Motor Shell: Coated Steel
• Housing: Polypropylene
• Valves: Viton
• Diaphragm: Santoprene
• Fasteners: Stainless Steel

NSF/ANSI Certified:
• NSF/ANSI Standard 61 - Drinking Water System Components - Health Effects
• NSF/ANSI 372 and conforms with the lead content requirements for “lead free” plumbing as defined by California, Vermont, Maryland, and Louisiana state laws and the U.S. Safe Drinking Water Act

Manufacturer Recommendation:
• If you are going to be running continuous use with any bypass model of pump, Delavan also recommends that you purchase a heat sink for the motor

Pump:
• Bypass Design – Continuous operation
• Type: 5-chamber positive displacement
• Capable of being run dry
• Excellent self-priming capability
• Liquid Temperature: 140° F Max.
• Priming Capabilities: 14’
• Max. Flow: 5.0 GPM
• Max Pressure: 60 PSI
• Pressure Settings: 70 PSI
• Inlet/Outlet Ports: 1/2” FNPT
• Packaging: Small box
• Weight: 7.0 lbs

Delavan PowerFLO™ 7812 Series 2.0 GPM 60 PSI Diaphragm Pump with On/Off Switch 3/8” FNPT Ports. Demand Switch – Operates only when liquid flow is required

Features:
• Certified to NSF/ANSI Standard 61 & 372
• Made in the USA
• On/Off Switch
• 100% Factory tested
• 2 Year warranty from date of purchase

Motor:
• Type: 12 VDC permanent magnet, totally enclosed, non-ventilated
• Leads: 14 AWG, 6” long with 2-pin connector
• Max Amps: 10
• Duty Cycle: See Heat Rise graph

Materials of Construction:
• Motor Shell: Coated Steel
• Housing: Polypropylene
• Valves: Viton
• Diaphragm: Santoprene
• Fasteners: Stainless Steel

NSF/ANSI Certified:
• NSF/ANSI Standard 61 - Drinking Water System Components - Health Effects
• NSF/ANSI 372 and conforms with the lead content requirements for “lead free” plumbing as defined by California, Vermont, Maryland, and Louisiana state laws and the U.S. Safe Drinking Water Act

Pump:
• Demand Switch – Operates only when liquid flow is required
• Type: 3-chamber positive displacement
• Capable of being run dry
• Excellent self-priming capability
• Liquid Temperature: 140°F Max.
• Priming Capabilities: 14’
• Max. Flow: 2.0 GPM
• Pressure Shut-Off: 60 PSI
• Inlet/Outlet Ports: 3/8” FNPT
• Packaging: Small box
• Weight: 5.6 lbs

Blue Clean PW9091H 25' Replace/Extension Pressure Washer Super Soft Hose. 25′ of extra soft pressure washer hose with M22-15MM connections. This replacement or extension hose can fit many electric pressure washers & can handle up to 2,900 PSI

Features:
• You can add 25′ To your existing pressure washer or use it as a replacement for your broken or misplaced AR Blue Clean hose
• The M22-15MM fittings make it one of the most adaptable hoses on the market
• The hose is non-marring, resistant to weather, abrasions, and kinking
• The 2 adapters make connecting or extending to your electric pressure washer a breeze!

Specifications
• Length: 25’
• Hose Fittings: Female M22-15MM
• Extesion Coupling M22-15MM x M22-15MM
• Series 100 Adapter: Only works with Blue Clean Models AR110S, AR111S, AR112S, AR112ST, AR141, AR142, AR142S, AR143S-Q2, AR144S, AR145S
• Working Pressure: 2,900 PSI
• Replaces # PW4220600, PW4221500, PW3083450
• Original Blue Clean replacement part
• Weight: 2.05 lb

General Pump DHRWM50200 3/8" x 200' Professional Hose Reel. Rated 4,000 PSI and up to 185° F. Heavy duty steel frame structure is ideal for pressure washer and sewer jetter use.

FEATURES
• Direct hand crank with locking pin
• Full flow swivel
• Solid steel construction
• Durable black powder coated finish
• 5,000 PSI rated swivel
• Reduces garage and workshop clutter
• Extends hose life!
• Wall mounting kit available (2100531)

SPECIFICATIONS
• Capacity: 200’ of 3/8” pressure washer/sewer jetter hose
• Max. PSI: 4,000
• Max Temp: 185° F.
• Color: Black
• Inlet: 3/8 NPT-M
• Outlet: 3/8 NPT-F
• Carton Dimensions: 16.0” x 17.5” x 17.5”
• Weight 19.0 lbs

General Pump DHRTM50200 3/8" x 200' Trailer Mount Hose Reel. Rated 5,000 PSI and up to 250° F. Heavy duty steel frame and 360° swivel rotation is ideal for pressure washer and sewer jetter use.

FEATURES
• Direct hand-crank rewind with locking pin
• Solid steel construction
• Durable black powder coated finish
• 360° swivel rotation
• Robust folding handle
• 180° pivoting hose guide
• Adjustable friction lever brake
• Full flow high pressure stainless steel swivel

SPECIFICATIONS
• Capacity: 200’ of 3/8” pressure washer/sewer jetter hose
• Max. PSI: 5,000
• Max Temp: 250° F.
• Color: Black
• Inlet: 1/2 NPT-F (Includes reducer 1/2NPT-M x 3/8NPT-F )
• Outlet: 1/2 NPT-F (Includes reducer 1/2NPT-M x 3/8NPT-F )
• Carton Dimensions: 26.0” x 18.0” x 17.75”
• Note: Mounting bracket not included
• Weight 33.0 lbs

Everflo EFHP2000-BOX High Pressure Diaphragm Pump. Take your pressure up a notch with the Everflo 12V 2.0 GPM, 200 PSI On-Demand Quick Attach High Pressure Plunger Pump

Features:
• Designed to handle 2 GPM and 200 PSI, making this the perfect pump for higher pressure spraying distance or atomized droplets for misting applications
• Featuring an in-line fuse for increased safety and reliability
• Comes standard with a variable pressure regulator that makes pressure adjustments a breeze
• Include QA ports for quick connections
• Plunger made of ceramic to increase the longevity of seals
• Save battery power with the automatic power switch that turns off pump when no flow is needed
• Comes standard with 6 common fittings: (1) Variable Pressure Regulator, (1) 3/8” hose barb fitting, (2) 1/2” hose barb fittings and (2) 1/2” NPT fittings
• Handles a max of 20 AMPs and has self-priming up to 8 feet
• Approved for use with Round-Up® & other agricultural brand herbicides & insecticides
• CE approved & has standard mounting pattern to fit most sprayer tanks

Specifications:
• Max. Pressure: 200 PSI
• Max. Flow: 2.0 GPM
• Power Supply: 12 Volt DC
• Self-Priming: Yes (Up to 8')
• Inlet/Outlet Ports: Quick Attach
• Max. Fluid Temperature: 140° F
• Max. Amps: 20.0
• Round UP® Ready: Yes
• Packaging: Small box
• Pump Dry Weight: 13.0 lbs

3/8” SJNR General Pump # 4.0 Rotating Sewer Jet Nozzle 5,000 PSI.

Features
• Side ports impact the sides of the pipe
• Polishes and maximizes line recovery
• Rear facing nozzles advance hose through pipe
• Heat-treated Stainless Steel nozzles are wear and corrosion resistant
• Great for pipe, sewer and drain cleaning
• Compact design allows for maneuverability and cornering within pipes
• High pressure nozzles are sized to match the flow and pressure specifications of the equipment

Specifications
• Nozzle Size: # 4.0
• Material: Stainless steel & Brass
• Maximum Pressure: 5,000 PSI
• Inlet: 3/8” NPT-F
• Outside Diameter (O.D.): .87”
• Length: 1.42”
• Weight: 1.8 oz

Please use Nozzle Chart to determine proper nozzle size

Nozzle Chart

1/4” SJNR General Pump # 4.5 Rotating Sewer Jet Nozzle 5,000 PSI.

Features
• Side ports impact the sides of the pipe
• Polishes and maximizes line recovery
• Rear facing nozzles advance hose through pipe
• Heat-treated Stainless Steel nozzles are wear and corrosion resistant
• Great for pipe, sewer and drain cleaning
• Compact design allows for maneuverability and cornering within pipes
• High pressure nozzles are sized to match the flow and pressure specifications of the equipment
• Works best on 2" to 4" Pipes

Specifications
• Nozzle Size: # 4.5
• Material: Stainless steel & Brass
• Maximum Pressure: 5,000 PSI
• Inlet: 1/4” NPT-F
• Outside Diameter (O.D.): .67”
• Length: 1.34”
• Weight: 1.4 oz

Please use Nozzle Chart to determine proper nozzle size

Nozzle Chart

NEW MTM Hydro 14.7022 PF22.2 Professional Foam Cannon Adjustable Air Intake and Fan with New Bottle Design Stands Up On Its Own. The MTM Hydro Foam Cannon offers not only adjustable fan blades but now offers an adjustable spray pattern (vertically or horizontally) as it throws thick foam onto your vehicle, house, fence, sidewalk, roof or other washable items. The chemical injection knob on top allows for more or less chemical to be drawn through the internal chamber, increasing or decreasing the foam output. This allows the internal agitator to create a dense foam

Features:
• Adjustable Spray Pattern (horizontal or vertical)
• Adjustable Fan Blades (jet-wide)
• Adjustable chemical injection knob
• Single cast plated brass body
• New stand up bottle
• Replaceable filter
• M22 and QC plug fittings included
• Approved For auto, RV, marine detailing agriculture and home cleaning

Note:
• The 1.1mm (3.0) nozzle will accommodate a variety of pressure washers typically in the lower GPM/PSI spectrum. The 1.1mm orifice will fit most residential pressure washers much more accurately than the installed 1.25mm (3.5) orifice and provide better foam from your MTM Foam Cannon
• The full spectrum of ratings are not supported by the 3.5 or 3.0 orifices included with this kit
• Other orifices may be required for higher flow machines that have lower PSI- Example: 2000 PSI with 3.5 GPM requires a 5.0 Orifice
• For larger orifices, you will know it does not work because you will experience starting and stopping of the foam cannon as your unloader slips in and out of bypass
• You will also get watery foam as the orifice size 3.5 is significantly smaller than the 5.0 needed for your machine
• MTM Foam Cannons will not work with flow sensing unloaders as you will experience the same results listed for an under-sized orifice
• Additional orifice sizes and replacement items available for purchase

Specifications:
• Min. Flow Rate: 1.4 GPM
• Max. Flow Rate: 5.3 GPM
• Min. Pressure: 1,100 PSI
• Max. Pressure: 5,000 PSI
• Max. Temp.: 140°
• Nozzle Size: #3.5 / 1.25mm (Installed), #3.0 / 1.10mm included
• 32oz Grey stand up bottle
• Fitting pack (2-peices) containing a 1/4" M22 adaptor and 1/4" QC Plated Steel Plug
• Weight: 1.10 lbs.

Fimco Industries 20V-25-700-ATV VOLT EDGE™. The Volt Edge 25 Gallon ATV 7 Nozzle Boom Sprayer represents a major step in 21st Century Lithium Ion Battery powered technology. The polyethylene, UV resistant, high density tank has a 5 inch tethered lid for easy access and is completely drainable. This model features the best in class High Flo High Performance 2.4 GPM Pump with inline fuse protection. The Lever Grip Handgun distributes up to 30 feet of horizontal spray, 16 feet of vertical spray and comes with 15 feet of 3/8 inch hose. With a 7 Nozzle Folding Boom, this model distributes 12 feet of total spray coverage offering increased capacity with precise liquid application. Our FIMCO exclusive manifold places pressure control and boom operation conveniently at your fingertips to fine tune your spray pattern. A wireless remote and rechargeable Lithium Ion battery removes the need for additional lengthy wires attached to your ATV or UTV batteries. Compact, versatile and powerful, the new Volt Edge sprayers are optimized to deliver peak efficiency

Features:
• 2.4 GPM High Flo High Performance Pump features an internally fan cooled motor as well as chemically resistant valves and diaphragms which increase durability ensuring longer pump life
• Durable 25 Gallon blow molded tank features UV stabilizers and molded drain port and 5 inch lid for easy filling
• Folding 7 nozzle welded breakaway steel boom delivers 12 feet of total spray coverage, features Teejet® tips and is spring loaded for easy deployment, use and storage
• Lever grip handgun features an aluminum lance and a adjustable polymer nozzle that delivers 30 feet of horizontal spray and 16 feet of vertical spray. Plus 15 feet of hose gives you the length necessary to reach tight areas, around buildings and other obstacles
• Volt Edge 20 Volt Lithium Ion Sprayers provide on demand power when you need it most

Specifications:
• Warranty: 1 yr Consumer / 90 day Commercial
• Tank Size (Gal): 25
• Flow (GPM): 2.4
• Pressure (PSI): 60
• Spray Gun Type: Lever Handgun
• Spray Pattern: Adjustable Pattern Tip
• Pump Type: HIGH FLO
• Spray Height (ft.): 16
• Horizontal Spray Distance (ft.): 30
• Power Supply: Lithium Ion Battery
• Hose (in. x ft.): 3/8 x 15
• Boom Spray Coverage (ft.): 12
• Pump Warranty: 2 yr Consumer / 90 day Commercial
• Note: ATV & straps are not included
• Sprayer Weight: 54 lbs
• Ships Via Truck

Fimco Industries 20V-30-2N-TRL VOLT EDGE™ 30 Gallon 2 Nozzle Trailer Sprayer With 20V Lithium Ion Wireless Battery Powered System. This Trailer Series sprayer is powered by a High-Flow 2.4 GPM High Performance 12 Volt pump with 60 PSI maximum pressure. Perfect for spraying mosquitoes, ditches, pastures, fence rows, bean & corn crops, yards, parks & sport fields. Total coverage is 7 feet

VOLT EDGE™:
• Featuring a 20 Volt 5.0 Amp Hour Battery Pack
• 1 Amp Hour Charger
• Wireless remote control
• The Volt Edge™ System can deliver up to 60 minutes of use spraying 60 gallons of liquid per charge

Best In Class Pump:
• 2.4 GPM High Performance 12 Volt Pump
• Maximum Pressure Of 60 PSI
• Pressure Switch Turns Pump On & Off
• Self Priming
• Can Run Dry Without Damage
• Chemical Resistant Components
• Fan Cooled To Promote Longevity & Efficiency

MANIFOLD W/PRESSURE GAUGE:
• Lever Ball Valves Allow Flow & Pressure Control
• Easily Monitor Pressure With Highly Visible Gauge
• Quick Connect Fittings Enables Fast Configuration

DELUXE PISTOL GRIP HANDGUN:
• Up To 40 Feet Horizontal Spray
• Up To 25 Feet Vertical Spray
• Adjustable Spray Pattern

15 FEET OF 3/8 INCH HOSE:
• Chemical Resistant Rubber Hose
• Easy To Wrap For Storage
• Less Prone To Kinking

PREMIUM SPRAY TIPS:
• Premium Wide Angle Tips
• Reduces Chemical Drift
• Includes Anti-Drip Strainer

PRECISION SPRAY TECHNOLOGY:
• 2-Noule Boom Delivers 7 Feet Of Spray Coverage
• Break Away Steel Boom

INNOVATIVE BREAK AWAY BOOM:
• Boom Folds Backwards If Striking An Obstacle
• Boom Folds Forward For Compact Storage

Specifications:
• 12 Volt (Demand) Diaphragm Pump
• 2.4 GPM - 60 PSI
• Tank Size: 30 Gallon
• Sprayer Warranty: 1 Year (*90 DAY COMMERCIAL WARRANTY)
• Pump Warranty: 2 Year (*90 DAY COMMERCIAL WARRANTY)
• Carton Size: 40” x 20” x 20”
• Note: Lawn tractor is not included
• Sprayer Weight: 61 lbs

Fimco Industries 20V-UTV-45-BL VOLT EDGE™ The Volt Edge 45 Gallon UTV Boomless Broadcast Sprayer represents a major step in 21st Century Lithium Ion Battery powered technology. The polyethylene, UV resistant, high density roto molded tank has a 5 inch multi lid for easy access and is completely drainable. This model features the best in class High Flo High Performance 4.5 GPM Pump with inline fuse protection. The Deluxe Pistol Grip Handgun distributes up to 40 feet of horizontal spray, 28 feet of vertical spray and comes with 25 feet of 3/8 inch hose. This 3 Nozzle Boomless model distributes 36 feet of total spray coverage. Each Nozzle sprays independently offering increased efficiency with precise liquid application. Our FIMCO exclusive manifold places pressure control and boom operation conveniently at your fingertips to fine tune your spray pattern. A wireless remote and rechargeable Lithium Ion battery removes the need for additional lengthy wires attached to your UTV battery. Compact, versatile and powerful, the new Volt Edge sprayers are optimized to deliver peak efficiency

Features:
• 4.5 GPM High Flo High Performance Pump features an internally fan cooled motor as well as chemically resistant valves and diaphragms which increase durability ensuring longer pump life
• Deluxe pistol grip handgun delivers up to 40 feet of horizontal spray and 25 feet of vertical spray and features an ergonomic polymer handle and precision brass tip. 25 feet of hose gives you the length necessary to reach tight areas, around buildings and other obstacles
• Durable 45 Gallon roto molded tank features UV stabilizers, molded in baffles, boom mount transport handles
• Innovative top mounted boom design means you don't have to remove your tailgate to install our sprayer. Stainless steel 3 nozzle wet boom with broadcast tips delivers 36 feet of total spray coverage with Hypro tips that can be turned on and off independently
• Volt Edge 20 Volt Lithium Ion sprayers provide on demand power when you need it most

Specifications:
• Warranty: 1 yr Consumer / 90 day Commercial
• Tank Size (Gal): 45
• Flow (GPM): 4.5
• Pressure (PSI): 60
• Spray Gun Type: Deluxe Pistol Grip Handgun
• Spray Pattern: Adjustable Pattern Tip
• Pump Type: HIGH FLO
• Spray Height (ft.): 28
• Horizontal Spray Distance (ft.): 40
• Power Supply: Lithium Ion Battery
• Hose (in. x ft.): 3/8 x 25
• Boom Spray Coverage (ft.): 36
• Pump Warranty2 yr Consumer / 90 day Commercial
• Note: Utility Vehicle & straps are not included
• Sprayer Weight: 67 lbs
• Ships Via Truck

Fimco Industries 20V-20-DLX-SP. The Volt Edge 20 Gallon Spot Sprayer represents a major step in 21st Century Lithium Ion Battery powered technology. The polyethylene, UV resistant, high density tank has a 5 inch tethered lid for easy access and is completely drainable. This model features the best in class High Flo High Performance 2.4 GPM Pump with inline fuse protection. The Deluxe Pistol Grip Handgun distributes up to 40 feet of horizontal spray, 25 feet of vertical spray and comes with 15 feet of 3/8 inch hose. A wireless remote and rechargeable Lithium Ion Battery removes the need for additional lengthy wires attached to your ATV or UTV batteries. Compact, versatile and powerful, the new Volt Edge sprayers are optimized to deliver peak efficiency

Features:
• 2.4 GPM High Flo High Performance Pump features an internally fan cooled motor as well as chemically resistant valves and diaphragms which increase durability ensuring longer pump life
• Deluxe pistol grip handgun delivers up to 40 feet of horizontal spray and 25 feet of vertical spray and features an ergonomic polymer handle and precision brass tip. 15 feet of hose gives you the length necessary to reach tight areas, around buildings and other obstacles
• Durable 20 Gallon blow molded tank features UV stabilizers and molded drain port and 5 inch lid for easy filling
• Volt Edge 20 Volt Lithium Ion Sprayers provide on demand power when you need it most

Specifications:
• Warranty: 1 yr Consumer / 90 day Commercial
• Tank Size (Gal): 20
• Flow (GPM): 2.4
• Pressure (PSI): 60
• Spray Gun Type: Deluxe Pistol Grip Handgun
• Spray Pattern: Adjustable Pattern Tip
• Pump Type: HIGH FLO
• Spray Height (ft.): 25
• Horizontal Spray Distance (ft.): 40
• Power Supply: Lithium Ion Battery
• Hose (in. x ft.): 3/8 x 15
• Pump Warranty: 2 yr Consumer / 90 day Commercial
• Note: ATV & straps are not included
• Sprayer Weight: 24 lbs

Fimco Weed Wrangler 5281118, 5281560 1.0 GPM 60 PSI 12 Volt Diaphragm Pump. Replacement pump for spot sprayers, liquid fertilizer units, recreational activities, wash down or liquid transfer

Features:
• 1.0 GPM 12 Volt Automatic Demand
• In In-Line fuse protection – 5 Amp fuse
• Self priming
• Runs dry without damage
• Pumps are 100% flow and current tested at the factory

Specifications:
• Automatic demand diaphragm pump
• 12 Volt DC power
• 1.0 GPM max. flow
• 60 PSI pressure switch
• In-Line 5 AMP fuse protection
• 3/8” Hose barb connections
• Fimco Box #: 5151118
• Fimco Pump #: 5281560
• 1 Year consumer limited warranty
• Do not use for bleach or petroleum products
• Packaging: Small Box
• Weight: 1.50 lbs

Fimco Industries LAWN GUARD 4. The Lawn Guard 4 Gallon Multi Use Sprayer provides the ultimate in convenience and flexibility for small scale liquid application. This multifunctional Spot Sprayer is ideal for small scale liquid pest control application in confined areas. The UV resistant, molded polymer tank can be used as either a backpack sprayer, a pull behind sprayer or carried using a molded in handle. This model features a Micro Diaphragm Pump powered by a 3.6 Volt Lithium Ion Battery built into the spray wand. The wand features an adjustable tip distributing up to 20 feet of horizontal spray and 10 feet of vertical spray and comes with 6 feet of coiled hose. Sprayer is capable of spraying 13 gallons per charge and eliminates the need for hand pumping

Features:
• 0.2 GPM pump is durable and powerful providing 20 feet of horizontal spray and 10 feet of vertical spray
• Durable 4 Gallon blow molded tank features UV stabilizers and a molded in handle with 3 inch lid for easy filling
• Fully rechargeable handgun is durable and is coupled to 6 feet of coiled hose to reach tall corners and tight spots
• Wheel it, carry it, or pack it - the Lawn Guard portable lithium ion sprayer from FIMCO is a truly versatile system

Specifications:
• Warranty: 1 yr Consumer / 90 day Commercial
• Tank Size (Gal): 4
• Flow (GPM): 0.2
• Spray Gun Type: LI Handgun
• Spray Pattern: Adjustable Pattern Tip
• Spray Height (ft.): 10
• Horizontal Spray Distance (ft.): 20
• Power Supply: Lithium Ion Battery
• Hose (in. x ft.): 1/4 x 6
• Pump Warranty: 1 yr Consumer / 90 day Commercial
• Sprayer Weight: 20 lbs

Fimco model 60-3PT-BL 3 Point 60 Gallon Sprayer Complete with Boomless Nozzle, Pump & Handgun. The FIMCO 60 Gallon 3 Point Boomless Broadcast Sprayer is designed to work with small to mid-size farm tractors. The UV resistant, molded polymer tank has a 5 inch tethered lid for easy access and is completely drainable. This model features a Hypro 6 Roller Cast Iron Pump. The Deluxe Pistol Grip Handgun distributes up to 45 feet horizontal spray, 30 feet of vertical spray and comes with 25 feet of 3/8 inch hose. Built on a welded, powder coated steel frame this 3 Nozzle Boomless model distributes 36 feet of total spray coverage. Each Nozzle sprays independently offering increased efficiency with precise liquid application.

Features:
• 60 gallon thick wall roto molded chemical resistant tank with UV stabilizers with molded in baffles and sump for increased drainage
• Cast iron 6 roller pump provides up to 9 GPM with quick PTO coupler
• Category 1 hitch compatible
• Deluxe pistol grip handgun delivers up to 40 feet of horizontal spray and 25 feet of vertical spray and features an ergonomic polymer handle and precision brass tip. 25 feet of hose gives you the length necessary to reach tight areas, around buildings and other obstacles
• Stainless steel 3 nozzle wetboom with broadcast tips delivers 36 feet of total spray coverage with Hypro tips that can be turned on and off independently

Specifications:
• Manufacturers Warranty: 1 yr Consumer / 90 day Commercial
• Tank Size (Gal): 60
• Flow (GPM): 9.76
• Pressure (PSI): 150
• Spray Gun Type: Deluxe Pistol Grip Handgun
• Spray Pattern: Adjustable Pattern Tip
• Pump Type: Hypro 6 Roller Pump
• Spray Height (ft.): 30
• Horizontal Spray Distance (ft.): 45
• Power Supply: PTO
• Hose (in. x ft.): 3/8 x 25
• Boom Spray Coverage (ft.): 34
• Pump Warranty: 1 yr Consumer / 90 day Commercial
• Ships Via Truck

The FIMCO 110-3PT-17N 110 Gallon 3 Point Sprayer is designed to work with small to mid-size farm tractors. The UV resistant, molded polymer tank has an 8 inch lid for easy access and is completely drainable. This model features a Hypro 6 Roller Cast Iron Pump. The Pro Series Handgun distributes up to 45 feet horizontal spray, 30 feet of vertical spray and comes with 25 feet of 3/8 inch hose. Built on a welded, powder coated steel frame with folding 17 Nozzle Boom, this model distributes 28 feet of total spray coverage offering increased capacity with precise liquid application.

Features:
• Cast iron 6 roller pump provides up to 9 GPM with quick PTO coupler
• Category 1 hitch compatible
• Durable 110 Gallon roto molded tank features UV stabilizers and sump for increased drainage
• Folding 17 nozzle welded steel boom features Teejet® tips and is spring loaded for easy deployment, use and storage. Plus it provides 28 feet of total spray coverage featuring air induction tips for less drift and no drip check valves
• Pro Series hand gun is corrosion resistant and allows you to control flow rate by changing tips. Features an adjustable trigger for stream, fan or anywhere in between. 25 feet of hose gives you the length necessary to reach tight areas, around buildings and other obstacles

Specifications:
• Tank: Manufacturers Warranty: 1 yr Consumer / 90 day Commercial
• Tank Size (Gal): 110
• Flow (GPM): 9.76
• Pressure (PSI): 150
• Spray Gun Type: Pro Series 22" Handgun
• Spray Pattern: Adjustable Pattern Tip
• Pump Type: Hypro 6 Roller Pump
• Spray Height (ft.): 30
• Horizontal Spray Distance (ft.): 45
• Power Supply: PTO
• Hose (in. x ft.): 3/8 x 25
• Boom Spray Coverage (ft.): 28
• Pump Warranty: 1 yr Consumer / 90 day Commercial
• Ships Via Truck

Fimco Industries VOLT EDGE™ 20V-5.0AH-BAT. The Volt Edge 20V Replacement Battery represents a major step in 21st Century Lithium Ion Battery powered technology. Designed to extend your spraying time with a spare 20 Volt 5.0 Amp Hour Battery, this is an OEM interchangeable battery for Volt Edge sprayers and conversion kits. Innovation is everything and the Volt Edge Conversion Kit delivers the consistency, power and performance you need to get your work done

Features:
• 20 Volt Lithium Ion Battery provides on demand power when you need it most
• 5.0 amp hour battery can deliver up to 60 minutes of use spraying 60 gallons of liquid per charge

Specifications:
• Warranty: 1 yr Consumer / 90 day Commercial
• Power Supply: Lithium Ion Battery
• Compatible with the VOLT EDGE™ wireless battery system only
• Weight: 1.60 lbs

Fimco LAWN GUARD Lithium Ion Battery Powered Rechargeable Handgun / Pump. Easily Convert Your Pump Up Style Sprayer for Effortless Spraying. Roundup® Ready

Features;:
• No More Pumping – Rechargeable Lithium Ion Battery Diaphragm Pump Handgun
• 65 Minute Run Time
• Adjustable Nozzle From Straight Stream To Mist

Specifications:
• Flow: 0.2 GPM
• Vertical Spray Distance: 10’
• Horizontal Spray Distance: 20’
• Capacity: 13 Gallons per charge
• Run Time: 65 Minutes per charge
• Recharge TIme: 2.5 Hour
• Battery Charger: 3.6V
• Warranty: 1 Year (*90 DAY COMMERCIAL WARRANTY)
• Note: Sprayer & hose not included
• Weight: 2.25 lbs

The FIMCO 110-3PT-BL The FIMCO 110 Gallon 3 Point Boomless Broadcast Sprayer is designed to work with small to mid-size farm tractors. The UV resistant, molded polymer tank has an 8 inch lid for easy access and is completely drainable. This model features a Hypro 6 Roller Cast Iron Pump. The Pro Series Handgun distributes up to 45 feet horizontal spray, 30 feet of vertical spray and comes with 25 feet of 3/8 inch hose. Built on a welded, powder coated steel frame this 2 Nozzle Boomless model distributes 34 feet of total spray coverage. Each Nozzle sprays independently offering increased efficiency with precise liquid application

Features:
• Cast iron 6 roller pump provides up to 9 GPM with quick PTO coupler
• Category 1 and 2 hitch compatible
• Durable 110 Gallon roto molded tank features UV stabilizers and sump for increased drainage
• Pro Series hand gun is corrosion resistant and allows you to control flow rate by changing tips. Features an adjustable trigger for stream, fan or anywhere in between. 25 feet of hose gives you the length necessary to reach tight areas, around buildings and other obstacles
• Stainless steel 3 nozzle wetboom with broadcast tips delivers 34 feet of total spray coverage with Hypro tips that can be turned on and off independently

Specifications:
• Manufacturers Warranty: 1 yr Consumer / 90 day Commercial
• Tank Size (Gal): 110
• Flow (GPM): 9.76
• Pressure (PSI): 150
• Spray Gun Type: Pro Series 22" Handgun
• Spray Pattern: Adjustable Pattern Tip
• Pump Type: Hypro 6 Roller Pump
• Spray Height (ft.): 30
• Horizontal Spray Distance (ft.): 45
• Power Supply: PTO
• Hose (in. x ft.): 3/8 x 25
• Boom Spray Coverage (ft.): 34
• Pump Warranty: 1 yr Consumer / 90 day Commercial
• Ships Via Truck

Fimco Industries VOLT EDGE™ 20V Lithium Ion Wireless Conversion Kit. The Volt Edge 20V Cordless Conversion Kit represents a major step in 21st Century Lithium Ion Battery powered technology. Designed to upgrade your traditional wired FIMCO sprayer by conveniently attaching to your current sprayer. Kit includes mounting saddle, a 20 Volt 5.0 Amp Hour Battery Pack, wireless receiver and remote. The conversion kit delivers up to 72 minutes of spraying and 100 gallons of liquid per charge. Innovation is everything and the Volt Edge Conversion Kit delivers the consistency, power and performance you need to get your work don

Features:
• 20 Volt Lithium Ion Battery provides on demand power when you need it most
• 20V Battery charging dock features easy to read display
• Universal polymer saddle fits most electric sprayer pumps (Check your mounting brackets to ensure fitment)
• Wireless remote gives you the flexibility to have control of your sprayer at your fingertips

Specifications:
• Warranty: 1 yr Consumer / 90 day Commercial
• Power Supply: Lithium Ion Battery
• Weight: 3.7 lbs

Fimco Industries 20V-25-BL-ATV VOLT EDGE™ The Volt Edge 25 Gallon ATV Boomless Broadcast Sprayer represents a major step in 21st Century Lithium Ion Battery powered technology. The polyethylene, UV resistant, high density tank has a 5 inch tethered lid for easy access and is completely drainable. This model features the best in class High Flo High Performance 4.5 GPM Pump with inline fuse protection. The Deluxe Pistol Grip Handgun distributes up to 40 feet of horizontal spray, 28 feet of vertical spray and comes with 15 feet of 3/8 inch hose. This 3 Nozzle Boomless model distributes 36 feet of total spray coverage. Each Nozzle sprays independently offering increased efficiency with precise liquid application. Our FIMCO exclusive manifold places pressure control and boom operation conveniently at your fingertips to fine tune your spray pattern. A wireless remote and rechargeable Lithium Ion battery removes the need for additional lengthy wires attached to your ATV or UTV batteries. Compact, versatile and powerful, the new Volt Edge sprayers are optimized to deliver peak efficiency

Features:
• 4.5 GPM High Flo High Performance Pump features an internally fan cooled motor as well as chemically resistant valves and diaphragms which increase durability ensuring longer pump life
• Deluxe pistol grip handgun delivers up to 40 feet of horizontal spray and 25 feet of vertical spray and features an ergonomic polymer handle and precision brass tip. 15 feet of hose gives you the length necessary to reach tight areas, around buildings and other obstacles
• Durable 25 Gallon blow molded tank features UV stabilizers and molded drain port and 5 inch lid for easy filling
• Stainless steel 3 nozzle wet boom with broadcast tips delivers 36 feet of total spray coverage with Hypro tips that can be turned on and off independently
• Volt Edge 20 Volt Lithium Ion sprayers provide on demand power when you need it most

Specifications:
• Warranty: 1 yr Consumer / 90 day Commercial
• Tank Size (Gal): 25
• Flow (GPM): 4.5
• Pressure (PSI): 60
• Spray Gun Type: Deluxe Pistol Grip Handgun
• Spray Pattern: Adjustable Pattern Tip
• Pump Type: HIGH FLO
• Spray Height (ft.): 28
• Horizontal Spray Distance (ft.): 40
• Power Supply: Lithium Ion Battery
• Hose (in. x ft.): 3/8 x 15
• Boom Spray Coverage (ft.): 36
• Pump Warranty2 yr Consumer / 90 day Commercial
• Note: Utility Vehicle & straps are not included
• Sprayer Weight: 35 lbs

Fimco model 60-3PT-7N 3 Point 60 Gallon Sprayer Complete with 7 Nozzle Boom, Pump & Handgun. The FIMCO 60 Gallon 3 Point Sprayer is designed to work with small to mid-size farm tractors. The UV resistant, molded polymer tank has a 5 inch tethered lid for easy access and is completely drainable. This model features a Hypro 6 Roller Cast Iron Pump. The Deluxe Pistol Grip Handgun distributes up to 45 feet horizontal spray, 30 feet of vertical spray and comes with 25 feet of 3/8 inch hose. Built on a welded, powder coated steel frame with folding 7 Nozzle Boom, this model distributes 12 feet of total spray coverage offering increased capacity with precise liquid application

Features:
• 60 gallon thick wall roto molded chemical resistant tank with UV stabilizers with molded in baffles and sump for increased drainage
• Cast iron 6 roller pump provides up to 9 GPM with quick PTO coupler
• Category 1 hitch compatible
• Deluxe pistol grip handgun delivers up to 40 feet of horizontal spray and 25 feet of vertical spray and features an ergonomic polymer handle and precision brass tip. 25 feet of hose gives you the length necessary to reach tight areas, around buildings and other obstacles
• Folding 7 nozzle welded breakaway steel boom delivers 12 feet of total spray coverage, features Teejet® tips and is spring loaded for easy deployment, use and storage

Specifications:
• Manufacturers Warranty: 1 yr Consumer / 90 day Commercial
• Tank Size (Gal): 60
• Flow (GPM): 9.76
• Pressure (PSI): 150
• Spray Gun Type: Deluxe Pistol Grip Handgun
• Spray Pattern: Adjustable Pattern Tip
• Pump Type: Hypro 6 Roller Pump
• Spray Height (ft.): 30
• Horizontal Spray Distance (ft.): 45
• Power Supply: PTO
• Hose (in. x ft.): 3/8 x 25
• Boom Spray Coverage (ft.): 12
• Pump Warranty: 1 yr Consumer / 90 day Commercial
• Ships Via Truck

Kuriyama PPBV075 3/4” Polypropylene Ball Valve 4-Bolt Design

Features:
• Full port
• Stainless steel bolts and nuts
• Teflon™ seats
• Viton® O-Ring stems and seals
• Polypropylene material is glass filled for extra strength
• Female NPT threads

Specifications:
• Size: 3/4”
• Type: Bolt valve
• Style: 4-Bolt Valve Design
• Connection Type: Female NPT
• Ball Material: Polypropylene
• Seal Material: Teflon™, Viton®
• Stem Material: Viton®
• PSI Rating at 70°F (+21°C): 150 PSI
• Weight: 0.85 lb

Fairview FLEX-DOT 1485 Series 3/4" x 250' Green Reinforced Air Brake Tubing - Type 3B. Air brake tube is designed for use with truck, trailer and other mobile air brake and auxiliary systems. This lightweight, flexible and UV stabilized tube is highly resistant to abrasion, oil, grease and road salt

MEETS OR EXCEEDS: D.O.T. F.M.V.S.S. 106 S.A.E. J844 TEST REQUIREMENTS

Compliance:
• All series 1485 tube are designed in compliance with the revised DOT 106 standard which took effect December 24th, 2007
• Fairview’s FLEX-DOT air brake tube is dimensionally identical to the previous air brake tube described in SAE J844 Type A and Type B, and is compatible with the same fittings. Both compression and push-to-connect fittings can be used with FLEX-DOT tube in all applications other than truck to trailer connections, in which push-to-connect fittings are not suitable

Materials:
• Both the core tube and jacket are comprised of a custom formulated elastomer, offering exceptional heat aging, oil resistance, and low temperature flexibility, when compared to previous nylon materials
• With its improved flexibility at all temperatures, the FLEX-DOT tube is easier to install in tight quarters
• The special compound was custom formulated for this application and offers exceptional flexibility even at very low temperatures. Unlike traditional all-nylon tube, the FLEX-DOT elastomer hose can still be flexed at -65C (-85F)

Specifications:
• Nominal OD: 3/4”
• Inside Diameter ID: 0.566”
• Wall Thickness: 0.092" +/-0.005"
• Length: 250’
• Temperature: -85°F to +200°F, -65°C to +93°C
• Type: 3B, Reinforced
• Color: Green
• Working Pressure: 200 PSI
• Minimum Burst @ 68°F: 800 PSI
• Supported Bend Radius: 3.00”
• Unsupported Bend Radius: 3.50”
• Approx. Weight: 27.0 lbs

Fairview FLEX-DOT 1485 Series 1/2" x 100' Green Reinforced Air Brake Tubing - Type 3B. Air brake tube is designed for use with truck, trailer and other mobile air brake and auxiliary systems. This lightweight, flexible and UV stabilized tube is highly resistant to abrasion, oil, grease and road salt

MEETS OR EXCEEDS: D.O.T. F.M.V.S.S. 106 S.A.E. J844 TEST REQUIREMENTS

Compliance:
• All series 1485 tube are designed in compliance with the revised DOT 106 standard which took effect December 24th, 2007
• Fairview’s FLEX-DOT air brake tube is dimensionally identical to the previous air brake tube described in SAE J844 Type A and Type B, and is compatible with the same fittings. Both compression and push-to-connect fittings can be used with FLEX-DOT tube in all applications other than truck to trailer connections, in which push-to-connect fittings are not suitable

Materials:
• Both the core tube and jacket are comprised of a custom formulated elastomer, offering exceptional heat aging, oil resistance, and low temperature flexibility, when compared to previous nylon materials
• With its improved flexibility at all temperatures, the FLEX-DOT tube is easier to install in tight quarters
• The special compound was custom formulated for this application and offers exceptional flexibility even at very low temperatures. Unlike traditional all-nylon tube, the FLEX-DOT elastomer hose can still be flexed at -65C (-85F)

Specifications:
• Nominal OD: 1/2”
• Inside Diameter ID: 0.376”
• Wall Thickness: 0.062" +/-0.004"
• Length: 100’
• Temperature: -85°F to +200°F, -65°C to +93°C
• Type: 3B, Reinforced
• Color: Green
• Working Pressure: 240 PSI
• Minimum Burst @ 68°F: 950 PSI
• Supported Bend Radius: 2.00”
• Unsupported Bend Radius: 2.50”
• Approx. Weight: 4.6 lbs

#4.5 PA UR25 / General Pump YR36K45 Blue Rotating Nozzle 3,650 PSI. Includes a quick connect inline filter to extend the life of the rotating nozzle.

Nozzle Features
• Offers 0° Impact, but with a 25° pattern
• Unique internal stabilization spring design allows for aim & shoot operation
• Nozzle can be pointed in any direction
• Shock resistant ceramic
• High Strength forged brass housing
• Durable rubber cover

Filter Features:
• 80 Mesh Screen
• Stainless Steel w/Brass Insert

Specifications
• Nozzle Size #4.5
• Max PSI: 3,650
• Max GPM: 7.7
• Max Temp.: 212° F
• Inlet: 1/4" QC Plug
• Minimum for operation: 1.6 GPM at 1,150 PSI
• Weight: 1.1 lbs

Please use Nozzle Chart to determine proper nozzle size

Nozzle Chart

#4.0 PA UR32 / General Pump YR51K40 Red Rotating Nozzle 5,100 PSI. Includes a quick connect inline filter to extend the life of the rotating nozzle.

Nozzle Features
• Offers 0° Impact, but with a 25° pattern
• Unique internal stabilization spring design allows for aim & shoot operation
• Nozzle can be pointed in any direction
• Shock resistant ceramic
• High Strength forged brass housing
• Durable rubber cover

Filter Features:
• 80 Mesh Screen
• Stainless Steel w/Brass Insert

Specifications
• Nozzle Size #4.0
• Max PSI: 5,000
• Max GPM: 9.9
• Max Temp.: 212° F
• Inlet: 1/4" QC Plug
• Minimum for operation: 2.4 GPM at 2,600 PSI
• Weight: 1.1 lbs

Please use Nozzle Chart to determine proper nozzle size

Nozzle Chart

#4.5 PA UR32 / General Pump YR51K45 Red Rotating Nozzle 5,100 PSI. Includes a quick connect inline filter to extend the life of the rotating nozzle.

Nozzle Features
• Offers 0° Impact, but with a 25° pattern
• Unique internal stabilization spring design allows for aim & shoot operation
• Nozzle can be pointed in any direction
• Shock resistant ceramic
• High Strength forged brass housing
• Durable rubber cover

Filter Features:
• 80 Mesh Screen
• Stainless Steel w/Brass Insert

Specifications
• Nozzle Size #4.5
• Max PSI: 5,000
• Max GPM: 9.9
• Max Temp.: 212° F
• Inlet: 1/4" QC Plug
• Minimum for operation: 2.4 GPM at 2,600 PSI
• Weight: 1.1 lbs

Please use Nozzle Chart to determine proper nozzle size

Nozzle Chart

#4.0 PA UR25 / General Pump YR36K40 Blue Rotating Nozzle 3,650 PSI. Includes a quick connect inline filter to extend the life of the rotating nozzle.

Nozzle Features
• Offers 0° Impact, but with a 25° pattern
• Unique internal stabilization spring design allows for aim & shoot operation
• Nozzle can be pointed in any direction
• Shock resistant ceramic
• High Strength forged brass housing
• Durable rubber cover

Filter Features:
• 80 Mesh Screen
• Stainless Steel w/Brass Insert

Specifications
• Nozzle Size #4.0
• Max PSI: 3,650
• Max GPM: 7.7
• Max Temp.: 212° F
• Inlet: 1/4" QC Plug
• Minimum for operation: 1.6 GPM at 1,150 PSI
• Weight: 1.1 lbs

Please use Nozzle Chart to determine proper nozzle size

Nozzle Chart